Graco 207947 Operation manual

307005F
EN
Instructions - Parts List
High Pressure Swivels
Models 207947, 196337, 207948
6000 psi (41 MPa, 414 bar) Maximum Working Pressure
Models 207946, 24P834
6500 psi (45 MPa, 448 bar) Maximum Working Pressure
Models 17G981, 17G980
7250 psi (50 MPa, 500 bar) Maximum Working Pressure
Model 207946, Series B, 17G981, Series A,
Model 24P834, Series A, and 17G980,
Series A
Straight Swivel; 3/8 npt(f) x 1/2 npsm(f)
Model 207947, Series B and
Model 196337, Series A
Straight Swivel; 1/2 npt(m) x 1/2 npt(f)
Important Safety Instructions
Read all warnings and instructions in this
manual before using the equipment.
Save these instructions.
WARNING
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely serious
injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.
• Do not exceed the maximum working pressure of the swivels.
• Always relieve pressure before removing, checking, or servicing the swivels.
• Do not stop or deflect leaks with your hand, body, glove or rag.
Ref. Part Description Qty.
1 102918 SEAL, polyurethane (207946, 17G981) 1
111689 SEAL, PTFE (24P834, 17G980) 1
2 168667 WASHER 1
3 168666 HOUSING, seal;
1-20 UNEF-2A(m) x 3/8-18 npt(f)
1
Ref. Part Description Qty.
1 102918 SEAL, polyurethane (207947 only) 1
111689 SEAL, PTFE (196337 only) 1
2 168667 WASHER 1
3 168670 HOUSING, seal;
1-20 UNEF-2A(m) x 1/2-14 npt(m)
1
01377
01373
3
12
3/8 npt(f
)
1/2 npsm(f)
3
12
1/2 npt(m
)
1/2 npt(f)
Install seal (1) with
“V” facing into seal
housing (3). 01380

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 307005
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 1992, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision F, July 2018
Optional PTFE Seal 111689
with stainless steel spring
For use with straight swivels 207946 and 207947 to
replace the polyurethane seal.
Straight Swivel Service
To replace the seal (1), unscrew the seal housing (3)
and remove the seal and back-up washer (2). Lubricate
the new seal with No. 2 lithium base grease and install
as shown above.
Model 207948, Series B
Zee Swivel; 1/2 npt(f) x 1/2 npt(m)
Zee Swivel Service
To replace the seal, remove the retaining ring (2) from
the swivel stud (5). Pull the swivel coupling (6) from the
swivel stud (5). Remove the seals (1) and washers (3).
Remove the retaining ring (2) from the seal housing (4).
Pull the swivel stud (5) from the seal housing (4).
Remove the seals (1) and washers (3).
Unscrew the seal housing (4) and remove the seal (1)
and washer (3).
Lubricate the new seals with No. 2 lithium base grease
and assemble as shown at right.
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest
distributor.
Phone: [phone] or Toll Free: 1-800-533-9655, Fax: [phone]
Ref. Part Description Qty.
1 102918 SEAL; polyurethane 5
2 102919 RING, retaining 2
3 168667 WASHER 5
4 168671 HOUSING, seal 1
5 168672 STUD, swivel 1
6 168673 COUPLING, swivel; 1/2-14 npt(m) 1
3
1
2
1/2 npt(f)
Install seal (1) with
“V” facing into seal
housing (4).
01375
4
31
352
3
1
3
6
1/2 npt(m)
01379
01380
Install seals (1) with
“V” facing in direction
shown.