Graco 25A187 Use and care manual

ti13853a
313753J
EN
Operation, Repair, Parts
Fine Finish HVLP
- For portable spray applications of fine finish coatings. For professional use only.-
240 Vac Models with ProComp: 25A187
240 Vac Models: 257829, 257830, 257831, 25A186
120 Vac Models: 257833, 257834, 257835
Maximum Working Pressure: 10 psi (0,07 MPa, 0.7 bar)
Important Safety Instructions
Read all warnings and instructions in this manual and related manuals.
Be familiar with the controls and the proper usage of the
equipment.Save these instructions.

TableofContents
2313753J
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Grounding and Electric Requirements . . . . . . . . 5
Component Identification . . . . . . . . . . . . . . . . . . . . 6
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fluid Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connect Fluid and Air Supply . . . . . . . . . . . . . . . 7
Pressure Relief Procedure . . . . . . . . . . . . . . . . . 7
Operation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sprayer Disassembly . . . . . . . . . . . . . . . . . . . . 10
Sprayer Assembly . . . . . . . . . . . . . . . . . . . . . . . 10
Turbine Replacement . . . . . . . . . . . . . . . . . . . . . . 11
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Models 257833, 257834, 257835, 257829, 257830,
257831, 25A186, 25A187 . . . . . . . . . . . . . . 14
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Models 257833, 257834, 257835, 257829, 257830,
257831, 25A186, 25A187 . . . . . . . . . . . . . . 15
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 18

Warnings
313753J 3
Warnings
The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation
point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to
these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applica-
ble.
WARNING
GROUNDING
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with
an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
• Improper installation of the grounding plug is able to result in a risk of electric shock.
• When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade
terminal.
• The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
• Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or
when in doubt as to whether the product is properly grounded.
• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electri-
cian.
• This product is for use on a nominal 120V/240V circuit and has a grounding plug similar to the plug illustrated in
the figure below.
• Only connect the product to an outlet having the same configuration as the plug.
• Do not use an adapter with this product.
Extension Cords:
• Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that accepts the plug
on the product.
• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG
(2.5 mm2) minimum to carry the current that the product draws.
• An undersized cord results in a drop in line voltage and loss of power and overheating.

Warnings
4313753J
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explo-
sion:
• Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes,
motors, and electrical equipment.
• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of
fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose
assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static
discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.
• Verify that all containers and collection systems are grounded to prevent static discharge.
• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.
• Do not use a paint or a solvent containing halogenated hydrocarbons.
• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in
a well ventilated area. Do not spray pump assembly.
• Do not smoke in the spray area.
• Do not operate light switches, engines, or similar spark producing products in the spray area.
• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.
• Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and
container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instruc-
tions.
• Fire extinguisher equipment shall be present and working.
• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep
sprayer at least 20 feet (6 m) away from explosive vapors.
ELECTRIC SHOCK HAZARD
Improper grounding, setup, or usage of the system can cause electric shock.
• Turn off and disconnect power cord before servicing equipment.
• Use only grounded electrical outlets.
• Use only 3-wire extension cords.
• Ensure ground prongs are intact on sprayer and extension cords.
• Do not expose to rain. Store indoors.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Always wear appropriate gloves, eye protection, and a respirator or mask when painting.
• Do not operate or spray near children. Keep children away from equipment at all times.
• Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not kink or over-bend the hose.
• Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.
• Do not use the hose as a strength member to pull or lift the equipment.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing
such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rup-
ture, and result in death, serious injury, and property damage.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equip-
ment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss.
This equipment includes but is not limited to:
• Protective eyewear and hearing protection
• Gloves, clothing and respirator as recommended by the fluid and solvent manufacturer
WARNING

Warnings
313753J 5
Grounding and Electric Requirements
This equipment requires a 240 Vac, 50 Hz, 15A circuit,
with a grounding receptacle.
Do not alter the ground prong or use an adapter.
Use 3-wire, 12 awg, 50 ft (15 m) or shorter, extension
cords with ground prong.
Sprayer Components Table
Sprayer Model Hose Gun Fluid Sets
HVLP 7.0 257829, 257833 30-ft 257827 EDGE #3
HVLP 9.0 257830, 257834 30-ft 257827 EDGE #3, #4
HVLP 9.5 257831, 257835 30-ft and 4-ft 257827 EDGE #2, #3, #4
HVLP MEGA 2.0 25A186 30-ft and 4-ft 257827 #3
HVLP MEGA 3.0 25A187 20-ft and 4-ft 24Y630 #3

ComponentIdentification
6313753J
Component Identification
H
K
J
B
A
C
D
F
E
G
L
U
N
P
R
ST
ti12854a
M
Item Description
ASprayer air outlet HVLP connector for air sup-
ply to HVLP spray Gun
BSprayer power
switch On/Off switch for sprayer motor
CFluid storage
compartment Provides storage for up to four fluid sets
DSprayer handle Folds flat for minimum stor-
age space
EPower
cord storage Provides storage for power cord
FAir filters (pre-fil-
ter and main) Provides filtered air for spray gun and motor
GSpray gun Graco EDGE™spray gun
with EasyGlide™trigger
HAir filter indicator Lights when air filter needs to
be cleaned or replaced
JConnector and
power cord
Provides power for sprayer
(power cord provided with
sprayer)
KResettablecircuit
breaker Provides protection for motor
LQuick
connect Enables quick connection to
spray gun
MAir valve Provides HVLP 9.0 and 9.5 sprayers ability to shut off air
to spray gun
NAir hose Hose, 30 ft x 1 in., that con-
nects spray gun and sprayer.
PHose wrap Provides storage for air hose
when air hose is not in use
RStorage tray Provides extra storage
SCleaning cup
holder Provides storage for clean- ing cup
TEDGE spray gun
holder Provides external storage for spray gun
UHose, 4-ft Allows increased flexibility for
the HVLP 9.5
Item Description

Setup
313753J 7
Setup
Fluid Preparation
• Strain fluids before you spray. This includes color,
reducers and hardeners.
• Use a slower drying reducer or thinner to compen-
sate for the faster drying time caused by the warm air
of the turbine. Do not over reduce
• Sprayer performance varies with the viscosity of the
material sprayed and the length of the hose. To pre-
vent pressure drop, use hose supplied with sprayer.
• Most material manufacturers provide recommenda-
tions for their materials. Follow these recommenda-
tions.
Connect Fluid and Air Supply
Spray Gun with Siphon Cup
1. Connect air hose to sprayer.
Hand tighten.
2. Connect air hose from sprayer to
inlet fitting of gun.
3. Fill cup 3/4 full. Install cover. Latch
the gun cup cover to secure it to
siphon cup. See HVLP EDGE Gun
manual for operation instructions.
Connect to Electric Supply
Plug sprayer power cord into grounded outlet. Grounding
and Electric Requirements, page 5.
Pressure Relief Procedure
1. Turn off sprayer.
2. Unplug sprayer.
3. Unlatch cup cover; loosen or remove cup from cover
to relieve pressure.
Operation Tips
• Turn sprayer on a few minutes before spraying to
allow warm-up.
• Ensure sprayer filter is clean before operating. Clean
filter, page 8.
• To adjust spray gun pattern, see HVLP EDGE Gun
manual.
• To get proper adhesion, ensure surface is completely
clean.
• Always spray with the least amount of pressure
required to provide the desired spray pattern and rate
of application. Spraying at pressures higher than nec-
essary wastes paint and can result in an orange peel
finish.
ti13082a
ti12797a
ti12872a
The spray gun siphon cup is pressurized by the gun
air supply. To reduce the risk of serious injury from
pressurized fluid or accidental spray from gun, always
turn off the air supply to the spray gun before remov-
ing the siphon cup.
Sparks can be expected during normal operation of
motor. These sparks can ignite fumes from flammable
liquids, dust particles, and other flammable sub-
stances in the spray area.
• Use additional hose if necessary, and ensure the
sprayer is operated in clean, dry, well ventilated
area.
• Never use sprayer inside spray booth.

Maintenance
8313753J
Maintenance
The sprayer system is lifetime lubricated. The only main-
tenance required is filter cleaning and replacement.
Filter Operation
The sprayer filter must be clean at all times to provide
sufficient air flow to cool the motor and atomize the fluid.
The sprayer has an air filter indicator light on the front
panel. The indicator light illuminates if the filter is clogged
or has low airflow.
Cleaning Filter
1. Turn off and unplug sprayer.
2. Loosen four screws (18), remove filter retainer (17)
and pre-filter (20).
3. Remove main filter (21) and clean using one of the
following methods:
• Tap filter gently on flat surface, dirty side down.
• Direct, compressed air (100 psi(7 bar, 70 MPa)
maximum) through filter panel in the opposite
direction of arrows on side of filter (from the clean
side to the dirty side.
• Soak filter for 15 minutes in water and mild deter-
gent. Rinse filter until clean. Air dry.
8049a
To avoid electric shock, never install a damp filter in
the turbine. Installing a damp filter in sprayer can also
damage turbine.
ti13061a
18
17
20
21

Troubleshooting
313753J 9
Troubleshooting
Problem Cause Solution
No fluid delivery No material, no remote cup pressur-
ization, hose or pickup tube clogged Check cup for material
Check for leaks at the container gas-
ket (1-quart remote cup cover).
Tighten cover if loose.
Check air flow (approximately 1/4
CFM) from male quick-disconnect at
Compact outlet.
Turn pressure regulator clockwise.
Look for pressure on gauge. (If no
pressure on gauge, check air line fit-
tings.)
Check hole in 1-quart remote cup
cover at needle valve for blockage or
dirt. Clean if necessary.
Check for obstructions.
Check if fluid pickup tube is loose.
Tighten.
Blow out and clear material hose.
Clean check valve. See manual.
Sprayer not starting No power Check outlet for power. Cycle red
rocker switch.
Check that correct IEC (modular)
cord is used and plugged in.
Check circuit breaker (38). Push to
reset.
Poor atomization Dirty filter Clean filter and replace as neces-
sary.
Extension cord too long Extension cord must be 3-wire, 12
AWG, 50 ft (15 m) or shorter.
Hose too long Replace with shorter hose. See
Graco Fine Finish Solutions brochure
for hose part numbers.
Circuit breaker trips Filter clogged Clean filter and replace as necessary
High ambient temperature Move sprayer to cooler area.
Excessive current draw Return to authorized service center.

Repair
10 313753J
Repair
Sprayer Disassembly
1. Remove four thumbscrews (18) and remove filter
retainer (17), prefilter (20) and main filter (16). Parts,
page 14.
2. Remove two screws (45) and inlet plug (36) from
HVLP box (1). Remove three motor wire connectors
from inlet plug (36).
3. Place sprayer upside down. Remove four screws (77)
from sprayer base plate (2).
4. Pull up sprayer base plate and attached parts.
Thread motor wires that connected to inlet plug
through access in HVLP box.
5. Repair or replace any required parts.
Sprayer Assembly
1. Replace duct gaskets (59, 60) and any other dam-
aged or worn parts. Replace circuit breaker (32), if it
has cycled. Remove residual adhesive from previous
gaskets by wiping any sticky surfaces with mineral
spirits solvent (also called white spirit). Let solvent
evaporate thoroughly before installing replacement
gasket.
2. Use an adjustable square with blade running full
length of longest side of duct (22), to position duct
perpendicular to the base (2). Hold duct in place to
keep duct perpendicular to base edge and carefully
remove square.
3. Turn sprayer upside-down. Carefully slip base plate
and attached parts down into HVLP box (1).
NOTE: Be sure duct to maintain duct alignment.
4. Thread motor wires that connect with plug (61)
through access port in HVLP box.
5. Use four screws (77) to secure base plate to HVLP
box (1). Use an adjustable clamp over the outside of
HVLP box (1) to align screw holes if necessary.
6. Install three motor wire connectors onto plug (61).
Install plug (61) with two screws (101) into HVLP box
(1).
7. Install filter gaskets (19), main filter (16) with arrow
facing into HVLP box (1), pre-filter (20), filter retainer
(17), and hose rack (35) with four thumbscrews (18).
To avoid injury, including electric shock turn off
sprayer and unplug power cord before performing any
repair procedures on the turbine.
ti13061a
18
17
16 20
ti13062a
ti13063a
36 45
ti12973a
77
2

Turbine Replacement
313753J 11
Turbine Replacement
Refer to Parts Drawing, page 16.
1. Follow Sprayer Disassembly procedure, page 10.
2. Remove gasket (21).
3. Remove three screws (14) from spacer (38).
4. Remove plate (15) and three spacers (38).
5. Remove motor wires from spade connectors.
6. Rotate turbine (11) from outlet fitting (29) and lift up
from spacers (41).
7. Remove three screws (14) from spacer (41).
8. Remove the three spacers (41).
9. Install new gaskets (21, 23, 24, 59 and 60). Use min-
eral spirits solvent (also called white spirit) to remove
any adhesive remaining from old gaskets.
10. Reassemble turbine using red high strength
primer-less thread locker on the threads of the three
screws (14). Also apply thread locker to inside
threads of spacers (38).
NOTE: Ensure the ground wire is connected to the
same location as before; between turbine (11)
through hole and spacer (41).
11. Use an adjustable square with the blade running the
full length of the longest side of the duct (22) to posi-
tion duct perpendicular to base (2). Hold duct in place
and carefully remove square to keep duct perpendic-
ular to edge of base. With sprayer upside down, care-
fully slip base plate and attached parts (see page 15)
down into HVLP box (1). NOTE: Be sure to maintain
duct alignment.
12. Reconnect wires. Attach plug (61) to HVLP box with
two screws (101).
NOTICE
Use of thread locker is CRITICAL to turbine assembly.
NOTICE
Use thread locker provided in turbine replacement kit
to avoid loosening of spacers due to turbine vibration.
Failure to use thread locker may result in premature
turbine failure.

WiringDiagrams
12 313753J
Wiring Diagrams
2
5
3
6
BK
W
G
GROUND
N
L
G
L
G
N
ti12765a
110V
5
10
347
1
8
12
16
2
9
6
Ref. Part Description Qty.
1 244273 Conductor, BK 1
2 15W486 Conductor, BK 1
3 15W485 Conductor, G/Y 1
4 15W484 Conductor, W 1
5 257333 Conductor, W, BK, G 1
6 240256 Conductor, W 1
7 114064 Plug, inlet 1
8 114403 Circuit Breaker, 15A 1
9 15V923 Plug, outlet, CompPack 1
10 114280 Light, indicator, 120V 1
11 120660 Switch, rocker 1
12 114279 Sensor, pressure 1
2
5
3
6
GROUND
N
L
G
LG
LINE
GL1
L2 L2
LOAD
L
G
N
BK
W
G
240V
ti12770a
Ref. Part Description Qty.
1 244273 Conductor, BK 1
2 15W486 Conductor, BK 1
3 15W485 Conductor, G/Y 1
4 15W484 Conductor, W 1
5 257333 Conductor, W, BK, G 1
6 15W488 Conductor, W 1
7 15W487 Conductor, BK 1
8 240558 Conductor, G/Y 1
9 240256 Conductor, W 1
10 114064 Plug, inlet 1
11 16A348 Circuit Breaker, 8A 1
12 15V923 Plug, outlet, CompPack 1
13 114286 Light, Indicator, 240V 1
14 120660 Switch, rocker 1
15 114279 Sensor, pressure 1
16 116168 Filter, suppression 1
310
15
8
4
6
7
9
14
16
11
2
12
13
5
1

Technical Data
313753J 13
Technical Data
120 Vac, 60 Hz
240 Vac, 50 Hz
* Sound Power and Sound Pressure are measured at 1 meter per ISO 3744
Ampere
Maximum
HoseLength
ft (m) Sprayer Weigh t lb (kg) Total Weight lb (kg) Sound Power* Sound Pressure*
HVLP 7.0 11,0 40 (12,2) 28 (12,7) 38 (17,2) 94.9 dBa 82 dBa
HVLP 9.0 12,0 60 (18,3) 29 (13,2) 39 (17,7) 95.9 dBa 83 dBa
HVLP 9.5 13,6 60 (18,3) 30 (13,6) 40 (18,1) 96.3 dBa 83.4 dBa
Ampere
Maximum
HoseLength
ft (m)
Sprayer Weight
lb (kg)
Total Weight
lb (kg) Sound Power* Sound Pressure*
HVLP 7.0 5,40 40 (12,2) 28 (12,7) 38 (17,2) 94.9 dBa 82 dBa
HVLP 9.0 5,93 60 (18,3) 29 (13,2) 39 (17,7) 95.9 dBa 83 dBa
HVLP 9.5 7,07 60 (18,3) 30 (13,6) 40 (18,1) 96.3 dBa 83.4 dBa
HVLP
MEGA 2.0 5,40 40 (12,2) 28 (12,7) 39 (17.7) 94.9 dBa 82 dBa
HVLP
MEGA 3.0 7,00 40 (12,2) 34 (15,4) 50 (22.7) 94.9 dBa 82 dBa

Parts
14 313753J
Parts
Models 257833, 257834, 257835, 257829, 257830, 257831, 25A186, 25A187
3
6
4
103
102
34 100 30
33
104
107
105
49
89
13
106
108
62
63
6
6
6
25
77
88
61
87
101
19
16
20
17
35 18
18
6
ti13855b

Parts List
313753J 15
Parts List
Models 257833, 257834, 257835, 257829, 257830, 257831, 25A186, 25A187
Ref. Part Description Qty .
1 277934 BOX, HVLP 1
3 24B055 COVER, HVLP, includes 6 1
4 15V791 HANDLE 1
6 15V771 LID, accessory 1
8 15V926 LATCH 2
13 HOSE, air
257159 30 ft, black 1
17H702 15 ft. MEGA 3.0
16 240273 FILTER, main 1
17 15W794 RETAINER, filter 1
18 15W897 SCREW, captive 4
19 15W217 GASKET, filter 2
20 15W909 FILTER, foam 1
25 113817 BUMPER 4
30 15W505 SCREW, mach, phillips pan hd 2
33 GUN 1
256855 HVLP, with cup
257827 MEGA 2.0, with cup
24Y630 MEGA 3.0, no cup
34 114271 STRAP, retaining 1
35 15V862 HOSE, rack 1
49 VALVE, air control
HVLP 7.0 (not included)
240065 HVLP 9.0 1
240065 HVLP 9.5, MEGA 3.0 1
61 15V923 PLUG, inlet 1
62 15W100 LABEL, safety 1
63 15W223 LABEL, safety 1
77 15W359 SCREW, mach, hex, washer hd 8
87 LABEL 1
15W639 Fine Finish
17H664 MEGA 2.0, MEGA 3.0
88 LABEL, HVLP
15W636 HVLP 7.0 1
15W637 HVLP 9.0 1
15W638 HVLP 9.5 1
17H662 MEGA 2.0, 1
17H663 MEGA 3.0 1
89 257161 HOSE, 4 ft, HVLP 9.5, MEGA 2.0,
MEGA 3.0 1
100 15V927 HINGE 2
101 117317 SCREW, plastite, pan hd 2
102 15X227 SCREW, cap, hex hd 2
103 102040 NUT, lock, hex 2
104 116234 BOTTLE 1
105 M70402 QUICK DISCONNECT 1
106 240475 HOSE, fluid, 20 ft., MEGA 3.0 1
107 17J918 HOSE, air, clear, 4 ft., MEGA 3.0 1
108 404989 STRAP, tie, MEGA 3.0 10
Extra Danger and Warning labels are available for free.
Ref. Part Description Qty .

PartsDrawing
16 313753J
Parts Drawing
Models 257833, 257834, 257835, 257829, 257830, 257831, 25A186, 25A187
ti12836e
14 21
15
11
24
48
2
58
86
22
60
42
44
106
39
59
41
38
29
9
27
30
110
64
24
5
31
109
107
108
46
45
14
36
45
32
56
45
23

Parts List
313753J 17
Parts List
Models 257833, 257834, 257835, 257829, 257830, 257831, 25A186, 25A187
Ref. Part Description Qty .
2 257066 PLATE, base, turbine, painted 1
5 114279 SENSOR, pressure 1
9 156698 O-RING 1
11*
+ TURBINE
15Y812 HVLP 7.0, 3-stage, 120V 1
15Y813 HVLP 9.0, 4-stage, 120V 1
15Y814 HVLP 9.5, 5-stage, 120V 1
15Y815 HVLP 7.0, 3-stage, 240V 1
MEGA 2.0, 3-stage, 240V 1
MEGA 3.0, 3-stage, 240V 1
15Y816 HVLP 9.0, 4-stage, 240V 1
15Y817 HVLP 9.5, 5-stage, 240V 1
14 114670 SCREW, cap, hex hd 6
15
+ 194094 PLATE, turbine 1
21
+ GASKET, turbine
15W153 HVLP 7.0, MEGA 2.0, MEGA 3.0 1
15W152 HVLP 9.0 1
192788 HVLP 9.5 1
22 15W274 DUCT, turbine 1
23
+ 16P954 GASKET, DUCT 1
24
+ 192845 GASKET, DUCT 1
27 120660 SWITCH, rocker 1
28 LIGHT, indicator
114280 120V 1
114286 240V 1
29 15W272 FITTING, outlet 1
30 114669 SCREW, mach, phillips pan hd 2
31 193059 GASKET, sensor 1
32 CIRCUIT Breaker
114403 120V, 15A 1
16A348 240V, 8A 1
36 114064 PLUG, INLET 1
37 192905 PLATE, deflector 1
38
+ SPACER, turbine
15W148 HVLP 7.0, MEGA 2.0, MEGA 3.0 3
15W149 HVLP 9.0 3
15W150 HVLP 9.5 3
39 192810 HOSE, air 1
41
+ 15X722 SPACER, turbine 3
42 111593 SCREW, grounding 1
44 102063 WASHER, lock, ext 1
45 SCREW, mach, torx pan hd
15W998 120V 4
15W998 240V 6
46 CORD, power
15W126 USA, 6 ft. 15A, 120V 1
116281 Euro, 2 m, 8A, 240V 1
128206 MEGA 2.0, MEGA 3.0, Euro, 6 ft,
240V (257829) 1
48 114287 FITTING, barbed 1
56 186620 LABEL, ground 1
5815K616 LABEL, brand, hot surface 1
59
+ 16E351 GASKET, duct, left 1
60
+ 16E353 GASKET, duct, right 1
6415W224 LABEL, safety 1
86 15W640 LABEL, brand, TurboForce 1
90 114689 BUSHING, strain relief 1
106 116168 FILTER, suppression, EMI, 240V 1
107 242001 CORDSET, adapter, Europe
(257830, 257831) 1
108 287121 CORDSET, adapter, 220V, global,
includes 108a through 108d 1
108a CORDSET, adapter, Italy 1
108b CORDSET, adapter, Denmark 1
108c CORDSET, adapter, Switzerland 1
109 195551 RETAINER, plug adapter 1
110 15X254 SWITCH INDICATOR LABEL 1
* Cleaning Brush Kits 256953 and 256954 are also available.
 Extra Danger and Warning labels are available for free.
+ Turbine kit includes items 9, 15, 21, 23, 24, 38, 41, 59 and 60
 Gasket/Breaker Kit 15 Amp 24F670 includes items 23,
32, 59, 60
 Gasket/Breaker Kit 10 Amp 24F671 includes items 23,
32, 59, 60
Ref. Part Description Qty .

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 313753
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2008, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised J, October 2015
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco
component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures,
accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the
claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made
at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the
warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the
furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of
Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de
ou en rapport, directement ou indirectement, avec les procédures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty Program”.
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.