Graco Pail Mount Packages Datasheet

Instructions–Parts List
309304P
EN
ALUMINUM AND STAINLESS STEEL, 1:1 RATIO
TritonR308
Spray Packages
100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
100 psi (0.7 MPa, 7 bar) Maximum Fluid Working Pressure
Pail Mount Packages
Stand Mount Packages
Cart Mount Packages
Wall Mount Packages
Important Safety Instructions
Read all warnings and instructions
in this manual. Save these instructions.
See page 2 for Table of Contents
and page 3 for Models.
TI1004b
TI1587b
Electrostatic packages Air Spray packages and HVLP packages

3093042
Table of Contents
Models 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warnings 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Identification 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List and Parts Drawing
Pail Mount 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stand Mount 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cart Mount 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Mount 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Mounting Template 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Standard Warranty 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Information 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

309304 3
Models
Spray Package Description Pail Mount,
Series Stand Mount, Series Cart Mount, Series Wall Mount, Series
Aluminum Pump,
No Gun 233466, A233473, A233480, A233487, A
Stainless Steel Pump,
No Gun 233467, A233474, A233481, A233488, A
Aluminum Pump,
AirPro Conventional Gun 233468, C233475, C233482, C233489, C
Stainless Steel Pump,
AirPro Conventional Gun 233469, C233476, C233483, C233490, C
Aluminum Pump,
AirPro HVLP Spray Gun 233470, C233477, C233484, C233491, C
Stainless Steel Pump,
AirPro HVLP Spray Gun 233471, C233478, C233485, C233492, C
Aluminum Pump,
AirPro Compliant Spray Gun 234911, B234913, B234915, B234917, B
Stainless Steel Pump,
AirPro Compliant Spray Gun 234912, B234914, B234916, B234918, B
Aluminum Pump,
Pro Xp 40 Electrostatic Spray Gun 233741, C233743, B233746, C233748, B
Aluminum Pump,
Pro Xp 60 Electrostatic Spray Gun 233742, C233744, B233747, C233749, B
Stainless Steel Pump,
AirPro HVLP Waterborne Gun N/A N/A 289632, A289622, A
Stainless Steel Pump,
AirPro Compliant Waterborne Gun N/A N/A 289633, A289623, A
Stainless Steel Pump,
AirPro Conventional Waterborne Gun N/A N/A 289634, A289624, A
Stainless Steel Pump,
AirPro HVLP Stain Spray Gun 289642, AN/A 289635, A289625, A
Stainless Steel Pump,
AirPro Compliant Stain Spray Gun 289643, AN/A 289636, A289626, A
Stainless Steel Pump,
AirPro Conventional Stain Spray Gun 289644, AN/A 289637, A289627, A
Aluminum Pump,
AirPro HVLP Stain Spray Gun 289645, AN/A 289638, A289628, A
Aluminum Pump,
AirPro Compliant Stain Spray Gun 289646, AN/A 289639, A289629, A
Aluminum Pump,
AirPro Conventional Stain Spray Gun 289647, AN/A 289640, A289630, A
Aluminum Pump,
Pro Xp 85 Electrostatic Spray Gun 289648, C289649, B289641, C289631, B

3093044
Symbols
Warning Symbol
WARNING
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.
WARNING
PRESSURIZED FLUID HAZARD
Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin
and cause serious injury.
DDo not stop or deflect fluid leaks with your hand, glove, or rag.
DFollow the Pressure Relief Procedure on page 10 before cleaning, checking, or servicing the
equipment.
DTighten all fluid connections before each use.
DCheck the hoses, tubes, and couplings daily. Replace parts immediately if worn, damaged, or
loose. Permanently coupled hoses cannot be repaired.
FIRE AND EXPLOSION HAZARD
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and
result in fire or explosion and serious injury.
DGround the equipment, the object being sprayed, and all other electrically conductive objects in the
spray area. See Grounding on page 10.
DElectrostatic guns require special grounding procedures. If your package includes an electrostatic
spray gun, read and follow all grounding instructions in the gun manual 3A2494.
DIf there is any static sparking while using the equipment, stop spraying immediately. Identify and
correct the problem.
DProvide fresh air ventilation to avoid the buildup of flammable vapors from the solvent or the fluid
being sprayed.
DDo not smoke in the spray area.
DExtinguish all open flames or pilot lights in the spray area.
DDo not turn on or off any light switch in the spray area.
DElectrically disconnect all equipment in the spray area.
DKeep the spray area free of debris, including solvent, rags, and gasoline.
DDo not operate a gasoline engine in the spray area.

309304 5
WARNING
INSTRUCTIONS
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result
in a serious injury.
DThis equipment is for professional use only.
DRead all the instruction manuals, tags, and labels before operating the equipment.
DUse the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.
DCheck the equipment daily. Repair or replace worn or damaged parts immediately.
DDo not exceed the maximum working pressure of the lowest rated system component. This pack-
age has a 100 psi (0.7 MPa, 7 bar) maximum working pressure.
DUse fluids that are compatible with the equipment wetted parts. See the Technical Data section of
all the equipment manuals. Read the fluid manufacturer’s warnings.
DAluminum pumps only: Never use 1.1.1–trichloroethane, methylene chloride, other halogenated
hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such
use could result in a chemical reaction, with the possibility of explosion.
DRoute the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not
expose Graco hoses to temperatures above 180_F (82_C) or below –40_F (–40_C).
DDo not use the hoses to pull equipment.
DWear hearing protection when operating this equipment.
DComply with all applicable local, state, and national fire, electrical, and other safety regulations.
TOXIC FLUID HAZARD
Hazardous fluids or toxic fumes can cause a serious injury or death if splashed in the eyes or on the
skin, swallowed, or inhaled.
DKnow the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.
DStore hazardous fluid in an approved container. Dispose of the hazardous fluid according to all
local, state, and national guidelines.
DWear appropriate protective clothing, gloves, eyewear, and respirator.
DIf the pump diaphragm fails, hazardous fluid may be exhausted along with the air.

3093046
Component Identification
ti1006a
ti1005b
KEY
A TRITON 1:1 Pump
B Bleed-type master air valve
C Air supply line (not supplied)
D Air line filter (not supplied)
E Air line shutoff valve (not supplied)
F Pump air regulator
G Gun air regulator
H Fluid pressure regulator (HVLP and
electrostatic packages only)
J Drain/circulation valve
K Drain tube
L Suction tube
M Gun fluid hose connection
N Gun air hose connection
P Gun fluid hose
R Gun air hose
S Spray gun
T Fluid pressure gauge (HVLP and
electrostatic packages only)
U Pump air pressure gauge
V Gun air pressure gauge
W Agitator (not supplied)
Y Pump ground wire
Fig. 1
A
F
G
L
K
M
N
P
Stand Mount HVLP Spray Package Shown
S
R
B
C
DE
Y
H
J
T
U
V
W

309304 7
Installation
CAUTION
Use a stainless steel package to spray waterborne,
acid-catalyzed, or 2-component materials. Use of
aluminum packages with these materials is not rec-
ommended. See the wetted parts in the Technical
Data section of each component manual, and your
fluid and solvent manufacturer’s compatibility infor-
mation.
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can
cause serious injury or death if splashed
in the eyes or on the skin, inhaled, or
swallowed.
DRead TOXIC FLUID HAZARD on page 5.
DUse fluids and solvents that are compatible with
the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals.
Read the fluid and solvent manufacturer’s
warnings.
General Information
DAlways use Genuine Graco Parts and Accessories,
available from your Graco distributor. If you supply
your own accessories, be sure they are adequately
sized and pressure rated for your system.
DReference numbers and letters in parentheses refer
to the callouts in the Figs. and the parts lists start-
ing on page 12.
Preparing the Site
DEnsure that you have an adequate compressed air
supply for the pump and gun. Refer to the separate
pump and gun manuals for air consumption data.
DClear obstacles and debris that could cause an
unsafe operating environment.
DHave a grounded, metal pail available for use when
flushing the spray package.
DBring an air supply line (C) from the main air supply
to the pump location. Install an accessory air filter
(D) on the compressed air line to filter dirt and
moisture from the air supply. Install a shutoff valve
(E) to isolate the filter for cleaning.
DWhen the bleed-type master air valve (B) is closed
and the pump air regulator (F) and gun air regulator
(G) are opened, it relieves all air pressure to the
system components.
DVentilate the spray booth.
WARNING
To prevent hazardous concentrations of toxic
and/or flammable vapors, spray only in a properly
ventilated spray booth. Never operate the spray
gun unless ventilation fans are operating.
Check and follow all of the national, state, and local
codes regarding air exhaust velocity requirements.

3093048
Installation
Pump Outlet Fluid Filter Accessories
To install a fluid filter on the pump outlet, order a filter
(AA), swivel (BB), and nipple (CC). Refer to Table 1 for
the part numbers you must order for an aluminum or a
stainless steel package.
Refer to Fig. 2. Install the fluid filter between the pump
fluid outlet and the gun fluid hose connection. If a fluid
regulator (H) is present, it must be rotated so the
gauge (T) will clear the filter.
Table 1: Installing a Fluid Filter
Fluid Filter (AA) Swivel (BB) Nipple (CC)
114361; nylon;
150 psi; 80 mesh;
for aluminum or
stainless steel
packages
235207;
3/8 npt(m) x 3/8
npsm(f); sst
166863;
1/4 npt x 3/8
npt; sst
235677; aluminum;
3000 psi; 60 mesh;
for aluminum
packages
157705;
1/4 npt(m) x 3/8
npsm(f); cst
165198;
1/4 npt x 3/8
npt; cst
223160; sst;
5000 psi; 60 mesh;
for stainless steel
packages
235207;
3/8 npt(m) x 3/8
npsm(f);
sst
166863;
1/4 npt x 3/8
npt; sst
Fig. 2
AA
BB
CC
H T
ti1471a
AA
Gun Inlet Filter
To install a filter between the hose and gun inlet, order
Filter 915921, 100 mesh, 500 psi, sst, 3/8 npsm (m x f).
Agitator Kit 245081
Part No. 245081 Agitator Kit is available for the
TRITON Sprayer Packages as an accessory. The kit
must be ordered separately. Instructions are included.
Fluid Suction Line
DThe pump fluid inlet is 3/4 npt(f). Screw the suction
line (L) into the pump inlet snugly. Use a compat-
ible liquid thread sealant on connections to prevent
air from getting into the fluid line.
DDo not pressure feed this pump.
DSee the Technical Data in the pump manual
309303 for maximum suction lift.
Preparing the Operator
Anybody who operates this system should be trained
in the safe, efficient operation of all system compo-
nents. At a minimum, all operators should thoroughly
read the TRITON operation manual, 309305.
Related Manuals
309305 TRITONt308 Spray Package Operation
309303 TRITONt308 Pump
312414 AirPro Conventional, HVLP, and
Compliant Gun
3A2494 Pro Xp Electrostatic Air Spray Guns
308325 Acetal Fluid Regulator
307212 Stainless Steel Fluid Regulator
309306 Agitator Kit

309304 9
Installation
Wall Mount Packages
NOTE: Refer to Fig. 3 and to the Wall Mounting Tem-
plate on page 21.
1. Ensure that the wall is strong enough to support
the weight of the pump and accessories, fluid,
hoses, and stress caused during pump operation.
2. Use the Wall Mounting Template on page 21 to set
the position of the wall bracket. The top edge of
the bracket should be 4 to 5 ft (1.2 to 1.5 m) above
the floor. Verify that the dimensions are exact and
the hole locations are level before drilling the
holes.
NOTE: It is easier to mount the wall bracket (31) if the
control bracket (4) and pump (1) are removed. Discon-
nect the air tube (12) from the elbow (11), then loosen
the two screws (3) and lift the control bracket (4) off
the screws. To remove the pump (1), remove the
screws (3) entirely.
3. Using the template, drill four 0.38 in. (9.6 mm)
diameter holes in the wall. Attach the bracket with
anchors and screws that are long enough to keep
the bracket from vibrating during operation. Check
that the bracket is level.
Suction Kit Accessories
Suction kits are available for the wall mount packages,
as an accessory. The kits must be ordered separately.
Refer to Table 2 for information.
ti1007a
Fig. 3
0.38 in.
(9.6 mm)
31
4
11
12
3
1
Table 2: Wall Mount Suction Kits
Part No. Suction Kit Description Hose Length Tube Length
245082 Aluminum, 5 gal pail size, with strainer 4 ft (1.2 m) 17 in. (0.43 m)
245083 Stainless Steel, 5 gal pail size, with strainer 4 ft (1.2 m) 17 in. (0.43 m)
245084 Aluminum, 55 gal drum size, with bung adapter 6 ft (1.8 m) 38 in. (0.96 m)
245085 Stainless Steel, 55 gal drum size, with bung
adapter 6 ft (1.8 m) 38 in. (0.96 m)

30930410
Installation
Grounding
WARNING
To reduce the risk of static sparking, the entire
system must be grounded. Check your local
electrical code for detailed grounding instructions
for your area and type of equipment. Ground all of
this equipment. Also read FIRE AND EXPLOSION
HAZARD on page 4.
DSpray package: One end of the ground wire is
already connected to the pump. Connect the clamp
end of the ground wire to a true earth ground.
DPackages with Pro Xp electrostatic guns: Make
sure you read all of the grounding instructions and
warnings in your gun instruction manual 3A2494.
DAir compressor: Follow the manufacturer’s recom-
mendations.
DObject being sprayed: Follow the local code.
DFluid supply container: Follow the local code.
DAll solvent pails used when flushing: Follow the
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non-conductive sur-
face, such as paper or cardboard, which interrupts
the grounding continuity.
Flush Pump Before First Use
The pump was tested in lightweight oil. If the test
solution could contaminate the fluid you are pumping,
flush the pump thoroughly with a compatible solvent.
Refer to the Operation Manual 309305 for flushing
instructions.
Pressure Relief Procedure
WARNING
The system remains pressurized until pressure is
manually relieved. To reduce the risk of serious
injury from pressurized fluid, accidental spray from
the gun, or splashing of any fluid, follow this proce-
dure whenever you
DStop spraying
DAre instructed to relieve pressure
DCheck or service any system equipment
DInstall, clean, or change spray nozzles
1. Close the bleed-type master air valve (B) to relieve
the air pressure.
2. On electrostatic guns only, turn the ES ON/OFF
lever to OFF.
3. Hold the gun (B) firmly against a grounded metal
pail and trigger the gun to relieve the fluid pres-
sure.
4. Place the drain tube (K) in a waste pail. Open the
drain/circulation valve (J) to relieve any fluid pres-
sure trapped in the system.