Graco 214570 Operation manual

307273ZAF
EN
Instructions/Parts List
Fluid Outlet Filter
For filtering of finishing materials. For professional use only.
See page 3 for model information, including maximum
working pressure and approvals.
Important Safety Instructions
Read all warnings and instructions in this
manualbeforeusingtheequipment.Save
these instructions.
2528a
Model 214570 shown

Contents
2307273ZAF
Contents
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pressure Relief Procedure. . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . 6
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Model 214570, Series B. . . . . . . . . . . . . . . . . . . . 8
Model 236789, Series A. . . . . . . . . . . . . . . . . . . . 8
Model 218029, Series B. . . . . . . . . . . . . . . . . . . . 9
Model 241317, Series A. . . . . . . . . . . . . . . . . . . . 9
Model 24V925, Series A . . . . . . . . . . . . . . . . . . . 9
Model 24T914, Series A . . . . . . . . . . . . . . . . . . . 9
Model 223160, Series B. . . . . . . . . . . . . . . . . . . 10
Model 24A587, Series B . . . . . . . . . . . . . . . . . . 10
Model 239800, Series A. . . . . . . . . . . . . . . . . . . 11
Model 240183, Series A. . . . . . . . . . . . . . . . . . . 12
Model 26A069, Series A . . . . . . . . . . . . . . . . . . 12
Model 238782, Series A. . . . . . . . . . . . . . . . . . . 13
Model 248851, Series A. . . . . . . . . . . . . . . . . . . 13
Model 239060, Series A. . . . . . . . . . . . . . . . . . . 14
Model 239244, Series A. . . . . . . . . . . . . . . . . . . 15
Model 239962, Series A. . . . . . . . . . . . . . . . . . . 16
Model 239964, Series A. . . . . . . . . . . . . . . . . . . 17
Model 239063, Series A. . . . . . . . . . . . . . . . . . . 18
Model 24F658, Series A . . . . . . . . . . . . . . . . . . 19
Model 239963, Series A. . . . . . . . . . . . . . . . . . . 20
Model 239961, Series A. . . . . . . . . . . . . . . . . . . 21
Model 240169, Series A. . . . . . . . . . . . . . . . . . . 22
Model 240170, Series A. . . . . . . . . . . . . . . . . . . 23
Model 239286, Series A. . . . . . . . . . . . . . . . . . . 24
Model 237481, Series A. . . . . . . . . . . . . . . . . . . 25
Model 241107, Series A. . . . . . . . . . . . . . . . . . . 25
Model 24F620, Series A . . . . . . . . . . . . . . . . . . 26
Model 24U609, Series A . . . . . . . . . . . . . . . . . . 26
Model 26B236, Series A . . . . . . . . . . . . . . . . . . 27
Kits and Accessories . . . . . . . . . . . . . . . . . . . . . . . 27
High Pressure Ball Valves . . . . . . . . . . . . . . . . . 27
Stainless Steel Screens . . . . . . . . . . . . . . . . . . . 27
Optional Filter Support . . . . . . . . . . . . . . . . . . . . 27
Technical Specifications . . . . . . . . . . . . . . . . . . . . 28
California Proposition 65 . . . . . . . . . . . . . . . . . . . . 28
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 30

Contents
307273ZAF 3
Models
Part Series Description Outlet Size Maximum Working Pressure
psi (MPa, bar)
214570 B Aluminum bowl, polyethylene support 1/4 npt 3000 psi (21 MPa, 210 bar)
236789 A Aluminum bowl, polyethylene support 3/8 npt 3000 psi (21 MPa, 210 bar)
237481 A Aluminum bowl, polyethylene support 3/8 npt 3000 psi (21 MPa, 210 bar)
239286 A Aluminum bowl, polyethylene support 1/4 npt 3000 psi (21 MPa, 210 bar)
218029 B Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239060 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
24F620 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239244 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
241317 B Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239962 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239964 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
240169 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
24T914 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
241107 A Carbon steel bowl, polyethylene support 3/8 npt 5000 psi (35 MPa, 350 bar)
223160 B Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
24A587 B Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239063 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239300 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239800 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239961 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
239963 A Stainless steel bowl, polyethylene support 1/4 npt 4000 psi (28 MPa, 280 bar)
240170 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
238782 A Stainless steel bowl, polyethylene support 3/8 npt 5000 psi (35 MPa, 350 bar)
248851 A Stainless steel bowl, polyethylene support 3/8 npt 5000 psi (35 MPa, 350 bar)
240183 A Stainless steel bowl, polyethylene support 1/2 npt 5000 psi (35 MPa, 350 bar)
24F658 A Stainless steel bowl, polyethylene support 1/2 npt 5000 psi (35 MPa, 350 bar)
24U609 A Stainless steel bowl, polyethylene support 1/2 npt 5000 psi (35 MPa, 350 bar)
24V925 A Carbon steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
26A069 A 316 sst bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)
26B236 A Stainless steel bowl, polyethylene support 1/4 npt 5000 psi (35 MPa, 350 bar)

Warnings
4307273ZAF
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.
When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this
manual where applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like
just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not spray without tip guard and trigger guard installed.
• Engage trigger lock when not spraying.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or
servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Warnings
307273ZAF 5
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Specifications in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical
Specifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For
complete information about your material, request Safety Data Sheets (SDSs) from distributor or
retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter ormodify equipment. Alterations or modificationsmay void agency approvals and create
safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read Safety Data Sheets (SDSs) to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical
reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or
property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents.
• Do not use chlorine bleach.
• Manyotherfluidsmaycontainchemicalsthatcanreactwithaluminum.Contactyourmaterialsupplier
for compatibility.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury, including
eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not
limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
WARNING

Installation
6307273ZAF
Installation
Install a suitable adapter in the filter inlet. See Technical
Specifications for fluid inlet size. Then install the filter
downstream from the pump fluid outlet.
Install a suitable adapter in the filter outlet. See
Technical Specifications for fluid outlet size. Connect
the spray hose to the filter outlet.
Operation
Pressure Relief Procedure
1. Lock the gun trigger safety.
2. Turn off the power to the pump.
3. Close any bleed-type master air valves.
4. Unlock the gun trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
6. Lock the gun trigger safety.
7. Open the system drain valve(s), having a container
ready to catch the drainage.
NOTE: Some models are supplied with a drain valve
(12). Refer to the parts list for your model.
8. Leave the drain valve(s) open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the tip or hose.
Maintenance
Cleaning the Filter
Dried paint sediment can clog the filter screen and
greatlyreduce filtering ability. Dried paint also makes the
filter difficult to remove. Clean the filter regularly; daily if
needed, following the procedure below.
1. Relieve the pressure.
2. Carefully remove the drain plug (1) from the bottom
of the filter bowl (7) to drain the fluid.
NOTE: Some models are supplied with a drain valve
(12). Refer to the parts list for your model. The drain
plug not used with Model 241107.
3. Unscrew the bowl from the filter housing (9).
4. Pull the screen (5) straight out of the bowl. (See
Kits and Accessories for other available screens.)
5. Remove the compression spring (8) from the filter
bowl (7).
6. To remove the filter support (6), gently push in on
the filter support stud. Replace the filter support if
the ridges are worn.
The system pressure must be manually relieved to
prevent the system from starting or spraying
accidentally. Fluid under high pressure can be
injected through the skin and cause serious injury. To
reduce the risk of an injury from injection, splashing
fluid, or moving parts, follow the Pressure Relief
Procedure whenever you:
• are instructed to relieve the pressure,
• stop spraying,
• check or service any of the system equipment,
• install or clean the spray tip.
NOTICE
To avoid damaging parts, never force them apart. If
any parts are stuck tightly together, soak them in a
compatible solvent before disassembling them. Be
careful not to drop or damage the filter housing and
bowl. Dirt, paint sediment, nicks or scratches may
prevent the o-ring (3) from seating properly.
WARNING
To reduce the risk of serious injury whenever you are
instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.

Maintenance
307273ZAF 7
7. Clean all parts thoroughly with a compatible solvent.
8. Place the filter support (6) in the screen (5) so the
support stud fits through the small opening in the
bottom of the screen.
9. Press fit the compression spring (8) to the bottom of
the filter bowl (7).
10. Carefully install the filter support (6) and screen (5)
into the filter bowl (7).
11. Replace the o-ring (3) if damaged or worn.
Lubricate the o-ring with No. 2 grease. Bend it into a
kidney shape, then carefully push it into the groove
to avoid damaging it.
12. Lubricate the filter bowl (7) threads and screw it
firmly into the housing (9).
NOTE: Be sure the bottom drain plug or drain valve is
closed before starting the pump.
Model 214570, 236789: Apply PTFE tape to all
non-swiveling pipe threads.
All other models: Apply anaerobic pipe sealant to all
non-swiveling pipe threads.
NOTICE
Improper assembly of the filter support, screen, and
spring will prevent filtering and damage parts.
FIG. 1: Model 214570 shown
3
Screw bowl firmly into housing
2529a
4
1
3
2
7
5
6
2
Press fit spring to bottom of bowl.
1
8
9
Lubricate.
1
1
2
3

Parts
8307273ZAF
Parts
Model 214570, Series B
ti38536a
1
7
8
5
3
4
29
6


Keep these parts on
hand to reduce down
time.
IG. 2: Model 214570
Model 236789, Series A
ti38537a
Keep these parts on
hand to reduce down
time.
1
7
8
5
3
4
29
6


IG. 3: Model 236789
F
Ref. Part Description Qty.
1 100040 PLUG; 3/8 npt; steel or iron 1
2 100509 PLUG; 1/4 npt; iron 2
3104361 O-RING; PTFE 1
4 162453 NIPPLE; 1/4 npsm x 1/4 npt 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 172831 BOWL, filter; aluminum 1
8 171941 SPRING, compression;
stainless steel 1
9 171942 HOUSING, filter; carbon steel 1
F
Ref. Part Description Qty.
1 100040 PLUG; 3/8 npt; steel or iron 1
2 100509 PLUG; 1/4 npt; iron 2
3104361 O-RING; PTFE 1
4155665 SWIVEL 1
5167025 SCREEN, stainless steel; 60 mesh 1
6186075 SUPPORT, filter; polyethylene 1
7172831 BOWL, filter; aluminum 1
8171941 SPRING, compression; stainless
steel 1
9188562 HOUSING, filter; carbon steel 1

Parts
307273ZAF 9
Model 218029, Series B
Model 241317, Series A
Model 24V925, Series A
Model 24T914, Series A
FIG. 4: Models 218029, Series B, 241317, Series A,
Model 24V925, Series A, Model 24T914, Series A
2530b
11
7
8
4
10
9
6
1
1
1
1
Used only on 241317
Keep these parts on
hand to reduce down
time.
5
3
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
4 162453 NIPPLE; 1/4 npsm x 1/4 npt 2
5167025 SCREEN, stainless steel; 60 mesh
(Models 218029 and 241317 only) 1
167024 SCREEN, stainless steel; 30 mesh
(Model 24T914 only) 1
167026 SCREEN, stainless steel; 100
mesh (Model 24V925 only) 1
6 186075 SUPPORT, filter; polyethylene 1
7 24C501 BOWL, filter; carbon steel. Model
218029, 24V925, and 24T914. 1
246582 BOWL, filter; stainless steel.
Model 241317.
8 171941 SPRING, compression; stainless
steel 1
9 171942 HOUSING, filter; carbon steel 1
10 100509 PLUG, pipe; 1/4 npt 1
11 157350 ADAPTER, 3/8 npt x 1/4 npt 1

Parts
10 307273ZAF
Model 223160, Series B
Model 24A587, Series B
FIG. 5: Models 223160, Series B and 
24A587, Series B
Model 223160 Model 24A587
7
8
410
9
6Keep these parts on
hand to reduce down
time.
5
3
1
9
4
22
Ref. Part Description Qty.
1 110740 PLUG; 3/8 npt; stainless steel 1
2 111697 PLUG; 1/4 npt; stainless steel 2
3104361 O-RING; PTFE 1
4 166846 NIPPLE; 1/4 npsm x 1/4 npt;
stainless steel 1
5167025 SCREEN, stainless steel; 60 mesh 1
6186075 SUPPORT, filter; polyethylene 1
7185632 BOWL, filter; stainless steel 1
8171941 SPRING, compression; stainless steel 1
9185631 HOUSING, filter; stainless steel 1
10 235208 SWIVEL, 3/8–18 npsm x 3/8–18 npt
(Model 24A587) 1

Parts
307273ZAF 11
Model 239800, Series A
FIG. 6: Model 239800, Series A
1
7
8
5
3
4
2
9
6


Keep these parts on
hand to reduce down
time.
Ref. Part Description Qty.
1 235992 VALVE, ball; 3/8 npt (mbe);
stainless steel 1
2 111697 PLUG; 1/4 npt; stainless steel 2
3104361 O-RING; PTFE 1
4 164856 ADAPTER; 3/8 npt x 1/4 npt
(mbe); stainless steel 1
5167026 SCREEN, stainless steel; 100
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 185632 BOWL, filter; stainless steel 1
8 171941 SPRING, compression; stainless
steel 1
9 185631 HOUSING, filter; stainless steel 1

Parts
12 307273ZAF
Model 240183, Series A Model 26A069, Series A
FIG. 7: Model 240183, Series A
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 185632 BOWL, filter; stainless steel 1
8 171941 SPRING, compression; stainless
steel 1
9 192975 HOUSING, filter; stainless steel 1
7
8
5
3
9
6


Keep these parts on hand
to reduce down time.
FIG. 8: Model 26A069, Series A
Ref. Part Description Qty.
1 26A078 VALVE, ball; 3/8 npt (mbe);
stainless steel 1
2 110740 PLUG; 3/8 npt; stainless steel 1
3104361 O-RING; PTFE 1
4 17K786 ADAPTER; 3/8 npt x 1/4 npt
(mbe); stainless steel 1
517K787 SCREEN, stainless steel; 100
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 17K788 BOWL, filter; stainless steel 1
8 17K789 SPRING, compression; stainless
steel 1
9 17K790 HOUSING, filter; stainless steel 1
10 101970 PLUG, 1/4npt, stainless steel 1
1
4
2
10
7
8
5
6
3
9
Keep these parts on hand
to reduce down time.

Parts
307273ZAF 13
Model 238782, Series A Model 248851, Series A
FIG. 9: Model 238782, Series A
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167024 SCREEN, stainless steel; 30 mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 196290 BOWL, filter; stainless steel 1
8 171941 SPRING, compression; stainless
steel 1
9 193331 HOUSING, filter; stainless steel 1
ti38538a
7
8
5
3
9
6


Keep these parts on hand
to reduce down time.
FIG. 10: Model 248851, Series A
Ref. Part Description Qty.
1 238782 FLUID FILTER ASSEMBLY;
see parts at left 1
2 101748 PLUG; 3/8 npt; stainless steel 1
3 111697 PLUG; 1/4 npt; stainless steel 3
4 166469 NIPPLE; 3/8 npt; stainless
steel 1
5 207123 ELBOW, swivel, 90° 1
ti15371a
1
5
3
4
2
3

Parts
14 307273ZAF
Model 239060, Series A
FIG. 11: Model 239060, Series A
7001a
1
7
8
5
3
4
9
6


10
12
13
14 Keep these parts on
hand to reduce down
time.
Ref. Part Description Qty.
1 100040 PLUG; 3/8 npt; steel or iron 1
3104361 O-RING; PTFE 1
4 162453 NIPPLE; 1/4 npsm x 1/4 npt;
carbon steel 1
5167025 SCREEN, stainless steel; 60 mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 24C501 BOWL, filter; carbon steel 1
8 171941 SPRING, compression; stainless
steel 1
9 171942 HOUSING, filter; carbon steel 1
10 100509 PLUG, pipe; 1/4 npt 1
12 238635 VALVE, ball; 1/4 npt (mbe); carbon
steel 1
13 205447 COUPLING; 1/4 npsm(f) 1
14 061132 TUBE, drain; nylon; 1/4 in. (0.6 mm)
ID; 8 in. (203 mm) 1

Parts
307273ZAF 15
Model 239244, Series A
FIG. 12: Model 239244, Series A
7007a
19
7
8
5
3
12
14
9
6


13
18
15
10
16
17
Keep these parts on
hand to reduce down
time.
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 24C501 BOWL, filter; carbon steel 1
8 171941 SPRING, compression; stainless
steel 1
9 171942 HOUSING, filter; carbon steel 1
10 100509 PLUG, pipe; 1/4 npt 1
12 238635 VALVE, ball; 1/4 npt (mbe);
carbon steel 1
13 205447 COUPLING; 1/4 npsm(f) 1
14 061132 TUBE, drain; nylon;1/4 in. (0.6
mm) ID; 8 in. (203 mm) 1
15 159841 BUSHING; 3/8 npt(m) x 1/4 npt(f) 1
16 100840 ELBOW, 90°, 1/4 npt (m x f);
carbon steel 1
17 156849 NIPPLE; 3/8 npt; carbon steel 1
18 102814 GAUGE, pressure 1
19 113444 ELBOW, 45°; 1/4 npt (m x f);
brass 1

Parts
16 307273ZAF
Model 239962, Series A
FIG. 13: Model 239962, Series A
8018a
21
7
8
15
12
9
6
17
16
18
20
17
5
3

Keep these parts on hand to
reduce down time.
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 24C501 BOWL, filter; carbon steel 1
8 171941 SPRING, compression; stainless
steel 1
9 171942 HOUSING, filter; carbon steel 1
12 238635 VALVE, ball; 1/4 npt (mbe);
carbon steel 1
15 159841 BUSHING; 3/8 npt(m) x 1/4 npt(f) 1
16 100840 ELBOW, 90°; 1/4 npt (m x f);
carbon steel 1
17 162453 NIPPLE; 1/4 npt x 1/4 npsm;
carbon steel 2
18 102814 GAUGE, pressure 1
20 164259 ELBOW, 90; 3/8 npt(m) x 1/4 npt
(f) 1
21 156953 STUD, mounting 1

Parts
307273ZAF 17
Model 239964, Series A
FIG. 14: Model 239964, Series A
8020a
7
8
15
12
9
6
16
18
10
17
5
3

Keep these parts on hand to
reduce down time.
22
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 24C501 BOWL, filter; carbon steel 1
8 171941 SPRING, compression; stainless
steel 1
9 171942 HOUSING, filter; carbon steel 1
10 100509 PLUG, pipe; 1/4 npt 1
12 238635 VALVE, ball; 1/4 npt (mbe);
carbon steel 1
15 159841 BUSHING; 3/8 npt(m) x 1/4 npt(f) 1
16 100840 ELBOW, 90°; 1/4 npt (m x f);
carbon steel 1
17 162453 NIPPLE; 1/4 npt x 1/4 npsm;
carbon steel 1
18 102814 GAUGE, pressure 1
22 156849 NIPPLE; 3/8 npt; carbon steel 1

Parts
18 307273ZAF
Model 239063, Series A
FIG. 15: Model 239063, Series A
7003a
1
7
8
4
2
12
6
13
14
5
3

Keep these parts on
hand to reduce down
time.
Ref. Part Description Qty.
1 110740 PLUG; 3/8 npt; stainless steel 1
2 111697 PLUG; 1/4 npt; stainless steel 2
3104361 O-RING; PTFE 1
4 166846 NIPPLE; 1/4 npsm x 1/4 npt;
stainless steel 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 185632 BOWL, filter; stainless steel 1
8 171941 SPRING, compression; stainless
steel 1
9 185631 HOUSING, filter; stainless steel 1
12 239018 VALVE, ball; 1/4 npt (mbe);
stainless steel 1
13 111913 COUPLING; 1/4 npsm(f) 1
14 061132 TUBE, drain; nylon; 1/4 in. (0.6
mm) ID; 8 in. (203 mm) 1

Parts
307273ZAF 19
Model 24F658, Series A
FIG. 16: Model 24F658, Series A
7005b
18
7
8
16
12
9
6
15
17
13
14
19
Keep these parts on
hand to reduce down
time.
5
3

Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7185632 BOWL, filter; stainless steel 1
8171941 SPRING, compression; stainless
steel 1
9192975 HOUSING, filter; stainless steel 1
12 239018 VALVE, ball; 1/4 npt (mbe);
stainless steel 1
13 111913 COUPLING; 1/4 npsm(f) 1
14 061132 TUBE, drain; nylon; 1/4 in. (0.6
mm) ID; 8 in. (203 mm) 1
15 168160 BUSHING; 3/8 npt(m) x 1/4
npt(f) 1
16 15M859 FITTING, adapter, swivel; 1/2
npt (m) x 1/2 npsm (f);
stainless steel
1
17 114572 NIPPLE; 1/2 npt x 1/2 npsm;
stainless steel 1
18 112941 GAUGE, pressure 1
19 113933 ELBOW, 45°; npt (m x f);
stainless steel 1

Parts
20 307273ZAF
Model 239963, Series A
FIG. 17: Model 239963, Series A
8019a
7
8
18
6
12
15
53

Keep these parts on hand
to reduce down time.
17 16
21
9
20
17
Ref. Part Description Qty.
3104361 O-RING; PTFE 1
5167025 SCREEN, stainless steel; 60
mesh 1
6 186075 SUPPORT, filter; polyethylene 1
7 185632 BOWL, filter; stainless steel 1
8 171941 SPRING,compression;stainless
steel 1
9 185631 HOUSING, filter; stainless steel 1
12 239018 VALVE, ball; 1/4 npt (mbe);
stainless steel 1
15 168160 BUSHING; 3/8 npt(m) x 1/4
npt(f) 1
16 166866 ELBOW, 90°; 1/4 npt (m x f);
stainless steel
1
17 166846 NIPPLE; 1/4 npt x 1/4 npsm;
stainless steel
1
18 112941 GAUGE, pressure 1
20 112026 ELBOW, 90°; 3/8 npt (m x f) 1
21 192661 STUD, mounting 1
22 113070 NIPPLE; 3/8 x 1/4 npt; stainless
steel 1