Graco Sharpe B Series Parts list manual

Instructions/Parts
In-Line Filters and Coalescers
with Automatic Drains 310611G
EN
Air Filter with Automatic Drain
Part No. 22601, Series B
Maintenance
To maintain maximum filtering efficiency and to
avoid excessive pressure drop, the filter must be
kept clean. Bowl drainage is automatic with the
float drain. Remove the bowl to drain manually. A
visible coating of dirt on the filter element surface or
an excessive pressure drop is an indication that
cleaning is necessary.
Cleaning
To clean, it is not necessary to remove the com-
plete filter from the line. Disassembly is simple and
does not require tools. Before disassembly, shut off
the air supply and depressurize filter. Clean all
parts with cleaning solvent and blow out filter body
before reassembly. Wash filter element in cleaning
solvent and blow out from the inside.
Automatic Drain
The Automatic drain is equipped with a float actu-
ated device which automatically ejects liquid con-
taminates under pressure.
Specifications
Air Inlet 1/2 in. F.P.T.
Air Outlet 1/2 in. F.P.T.
Air Flow Capacity 100 cfm (3.2 m3/min.) at 100 psi
(0.7 MPa, 7 bar)
Max. Operating Pressure 175 psi (1.2 MPa, 12 bar)
Max. Temperature 150°F (65°C)
Parts (Series B)
Part No. Description
24U115 Automatic Drain
127289 O-Ring
16W811 Baffle End Cap
16W405 Filter Element
O-Ring
Filter Element
Automatic
Drain
(127289)
(16W405)
(24U115)
Baffle End Cap
(16W811)
ti22164a
Important Safety Instructions
Read all warnings and instructions in your
equipment manual. Save all instructions.

Coalescer with Automatic Drain
2 310611G
Coalescer with Automatic Drain
(Part No. 22605, Series B)
Installation
It is always recommended that a Sharpe air filter be
installed upstream of the coalescing filter to remove
0.01 micron and larger size particles and separate large
droplets of moisture from the air line.
Maintenance
To maintain maximum filtering efficiency and to avoid
excessive pressure drop, the filter must be kept clean.
Bowl drainage is automatic with the float drain. Remove
the bowl to drain manually. A visible coating of dirt on
the filter element surface or an excessive pressure drop
is an indication that cleaning is necessary.
Cleaning
To clean, it is not necessary to remove the complete fil-
ter from the line. Disassembly is simple and does not
require tools. Before disassembly, shut off the air supply
and depressurize coalescer. Clean all parts with clean-
ing solvent and blow out body before reassembly.
Replace coalescing element (part no. 16W407).
Pressure Drop Indicator
The differential pressure drop indicator on this unit is
designed to provide early detection of a clogged
coalescing filter element. As the filter element becomes
clogged the red indicator will start to rise while air is
flowing through the unit. When the pressure drop across
the element reaches 10-12 psi (.07-.08 MPa, 0.7-0.8
bar) the red indicator will be in full view and the element
should be replaced. Failure to replace the element when
the pressure drop exceeds 10 psi (.07 MPa, 0.7 bar) will
affect your air quality and tool efficiency.
Specifications
Air Inlet 1/2 in. F.P.T.
Air Outlet 1/2 in. F.P.T.
Air Flow Capacity 50 cfm (2 m3/min.) at 100 psi
(0.7 MPa, 7 bar)
Max. Operating Pressure 175 psi (1.2 MPa, 12 bar)
Max. Temperature 150°F (65°C)
Parts (Series B)
Part No. Description
24U115 Automatic Drain
24U117 Mounting Bracket Kit
127289 O-Ring
24U116 Pop-up Indicator Repair Kit
16W407 0.01 Micron Coalescer Element
16W811 Baffle End Cap
O-Ring
Coalescer
Automatic
Drain
(127289)
(24U115)
Element
(16W407)
Pop-up
Indicator
(24U116)
Baffle
End Cap
16W811
Mounting
Bracket Kit
(24U117)
ti22165a

Model 707F 3/4 in. In-Line Filter with Automatic Drain
310611G 3
Model 707F
3/4 in. In-Line Filter with
Automatic Drain
(Part No. 6920)
•Removes all liquids (oil and water)
•Filters Particulate down to 5 microns
•Features large REUSABLE filter element
•Disassemble and clean without tools
Specifications
Air Inlet 3/4 in. F.P.T.
Air Outlet 3/4 in. F.P.T.
Air Flow Capacity 300 cfm (8.4 m3/min.)
Max. Operating Pressure 175 psi (1.2 MPa, 12 bar)
Max. Temperature 150°F (65°C)
Model 707C
3/4 in. In-Line Coalescer with
Automatic Drain
(Part No. 6930)
•Effectively traps fine oil mists and microscopic parti-
cles down to 0.01 microns
•Spin-off bowl and coalescer filter element for quick
filter changes without tools
•Includes pressure drop indicator
•Recommended downstream of your refrigerated air
dryer
Specifications
Air Inlet 3/4 in. F.P.T.
Air Outlet 3/4 in. F.P.T.
Air Flow Capacity 115 cfm (3.2 m3/min.)
Max. Operating Pressure 175 psi (1.2 MPa, 12 bar)
Max. Temperature 150°F (65°C)
Model 707FC
1/2 in. In-Line Filter & Coalescer
with Automatic Drains
(Part No. 6910, Series C)
•Designed for use in prep stations
•Clean, dry air without the use of desiccant
•Ideal for protecting moisture sensitive tools
•STAGE 1 provides removal of water and contami-
nates down to 3 microns
•STAGE 2 provides removal of oil and sub-micronic
particles down to 0.01 microns
•Disassemble and clean without tools
Specifications
Air Inlet 1/2 in. F.P.T.
Air Outlet 1/2 in. F.P.T.
Air Flow Capacity 50 cfm (2 m3/min.) at 100 psi
(0.7 MPa, 7 bar)
Max. Operating Pressure 175 psi (1.2 MPa, 12 bar)
Max. Temperature 150°F (65°C)
Model 707FC
ti22158a

Self-Relieving Air Regulator (Part No. 22604)
4 310611G
Self-Relieving Air Regulator
(Part No. 22604)
I
Maintenance
If the air supply is kept clean, this regulator will provide
long periods of uninterrupted service. Erratic regulator
operation or loss of regulation is most always due to dirt
in the diaphragm area and cleaning is in order.
Cleaning
Depressurize regulator, remove bottom plug, spring
valve, and diaphragm. Clean parts with denatured alco-
hol, wipe off seat and blow out body with compressed
air. Reassemble parts as a unit and screw into regulator
before tightening bottom plug Make sure disc is in cen-
ter hole in body. Should regulator continue to malfunc-
tion, obtain diaphragm/valve repair kit (part no. 22680)
and replace parts provided.
Specifications
Air Inlet 3/8 in. F.P.T.
Air Outlet 1/4 in. F.P.T. (3 EA.)
Air Flow Capacity 100 cfm (2.8 m3/min.)
Max. Operating Pressure 160 psi (1.1 MPa, 11 bar)
Max. Temperature 150°F (65°C)
Parts
22682
22680
22685
Part No. Description
8230 Air Pressure Gauge
10028 Plug
22680 Diaphragm/Valve Repair Kit
22682 T-Handle Adjusting Screw
22685 Bottom Spring
22687 3/8 in. x 3/8 in. Nipple
34700 Outlet Valve
AIR REGULATOR
(22604)
AIR PRESSURE
GAUGE (8230)
NIPPLE
(22687)
PLUG
(10028)
OUTLET
VALVE
(34700)

Self-Relieving Air Regulator (Part No. 22604)
310611G 5

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 310611
SHARPE MANUFACTURING • P.O. BOX 1441, MINNEAPOLIS, MN 55440-1441
1-800-742-7731, www.sharpe1.com
Revision G, September 2013
1 Year Limited Warranty
Sharpe warrants this product to the original user against defective material or workmanship for a period of 1 year
from the date of purchase.
Sharpe reserves the right to determine whether the part or parts failed because of defective material, workmanship,
or other causes. Failures caused by accident, alteration, or misuse are not covered by this warranty.
Sharpe, at its discretion, will repair or replace products covered under this warranty free of charge. Repairs or
replacements of products covered under this warranty are warranted for the remainder of the original warranty
period.
Sharpe or its authorized service representatives must perform all warranty repairs. Any repair to the product by unau-
thorized service representatives voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fit-
ness for a particular purpose. Some states do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitations may not apply to you.
Sharpe Information
TO PLACE AN ORDER, contact your SHARPE distributor or call 1-800-742-7731 or visit our web site at
www.sharpe1.com.
Product Registration
Thank you for the purchase of your Sharpe®product. We greatly appreciate your business.
Important reasons to register your product:
•Registration enables Sharpe to notify you if there is a problem with your product.
•Improved Product Development - Your input helps us continue to design products that meet your needs.
For the most up-to-date information and to register your product, please go to www.sharpe1.com and click on
“Register Product.”