Graco T2 User manual

Instructions
T2
2:1 Ratio Transfer Pump
For use with polyurethane foam, polyurea, and similar non-flammable materials. For
professional use only.
Not for use in explosive atmospheres.
Model 295616 (55-gallon drum)
180 psi (1.2 MPa, 12 bar) Maximum Air Working Pressure
405 psi (2.7 MPa, 27 bar) Maximum Fluid Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
WLD
311882R
EN

Warnings
2311882R
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Moisture Sensitivity of Isocyanates . . . . . . . . . . . . 4
Isocyanate Hazard . . . . . . . . . . . . . . . . . . . . . . . 4
Foam Self-Ignition . . . . . . . . . . . . . . . . . . . . . . . . 4
Keep Components A and B Separate . . . . . . . . . 4
Changing Materials . . . . . . . . . . . . . . . . . . . . . . . 4
Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . 5
Typical Installation, without Circulation . . . . . . . . 5
Typical Installation, with Circulation . . . . . . . . . . 6
Typical Installation for Lubrication Applications . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Accessories . . . . . . . . . . . . . . . . . . . . . . 8
Air Line Accessories . . . . . . . . . . . . . . . . . . . . . . 8
Fluid Line Accessories . . . . . . . . . . . . . . . . . . . . 8
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Grounding the System . . . . . . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pressure Relief Procedure . . . . . . . . . . . . . . . . 11
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daily Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daily Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . 11
Air Motor Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pump Lower Repair . . . . . . . . . . . . . . . . . . . . . . . . 14
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parts - Model 295616 . . . . . . . . . . . . . . . . . . . . . . . 20
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Performance Chart . . . . . . . . . . . . . . . . . . . . . . 25
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 26
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 26
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
• Always wear impervious gloves when spraying or cleaning equipment.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
•Gloves
• Hearing protection

Warnings
311882R 3
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS forms from distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and
cause serious injury.
•FollowPressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
WARNING

Moisture Sensitivity of Isocyanates
4311882R
Moisture Sensitivity of Isocyanates
Isocyanates (ISO) are catalysts used in two component
foam and polyurea coatings. ISO will react with moisture
(such as humidity) to form small, hard, abrasive crystals,
which become suspended in the fluid. Eventually a film
will form on the surface and the ISO will begin to gel,
increasing in viscosity. If used, this partially cured ISO
will reduce performance and the life of all wetted parts.
To prevent exposing ISO to moisture:
• Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere. Never
store ISO in an open container.
• Use moisture-proof hoses specifically designed for
ISO, such as those supplied with your system.
• Never use reclaimed solvents, which may contain
moisture. Always keep solvent containers closed
when not in use.
• Never use solvent on one side if it has been
contaminated from the other side.
• Always lubricate threaded parts with Part 217374
ISO pump oil or grease when reassembling.
Isocyanate Hazard
Foam Self-Ignition
Keep Components A and B
Separate
Changing Materials
• When changing materials, flush the equipment
multiple times to ensure it is thoroughly clean.
• Check with your material manufacturer for chemical
compatibility.
• Some materials use catalyst on the A side, but
some applications may use catalyst on the B side.
• Epoxies often have amines on the B (catalyst) side.
Polyurethanes often have amines on the B (resin)
side.
The amount of film formation and rate of
crystallization varies depending on the blend of
ISO, the humidity, and the temperature.
Read material manufacturer’s warnings and material
MSDS to know the specific hazards of isocyanates.
Use equipment in a well-ventilated area. Wear
respirator, gloves, and protective clothing when using
isocyanates.
Some materials may become self-igniting if applied
too thick. Read material manufacturer’s warnings and
material MSDS.
CAUTION
To prevent cross-contamination of the equipment’s
wetted parts, never interchange component A and
component B.

Typical Installation
311882R 5
Typical Installation
Typical Installation, without Circulation
Key for F IG . 1
A Reactor Proportioner
B Heated Hose
C Fluid Temperature Sensor (FTS)
D Heated Whip Hose
E Fusion Spray Gun
F Proportioner and Gun Air Supply Hose
G Feed Pump Air Supply Lines (3/8 in. (76 mm) ID min.
H Waste Containers
J Fluid Supply Lines (217382)
K Feed Pumps
L Agitator
M Desiccant Dryer
N Bleed Lines/Over Pressure Relief
P Gun Fluid Manifold
F IG . 1: Typical Installation, without Circulation
A
B
C*
DE
K
L
M
F
P
N
* Shown exposed for clarity. Wrap with tape during operation.
K
H
J
G
ti11572a

Typical Installation
6311882R
Typical Installation, with Circulation
Key for F IG . 2
A Reactor Proportioner
B Heated Hose
C Fluid Temperature Sensor (FTS)
D Heated Whip Hose
E Fusion Spray Gun
F Proportioner and Gun Air Supply Hose
G Feed Pump Air Supply Lines (3/8 in. (76 mm) ID min)
J Fluid Supply Lines
K Feed Pumps
L Agitator
M Desiccant Dryer
N Recirculation/Over Pressure Relief Return Hoses
P Gun Fluid Manifold
F IG . 2: Typical Installation, with Circulation
A
B
C*
D
E
K
L
M
F
N
P
* Shown exposed for clarity. Wrap with tape during operation.
J
N
K
M
G
ti11571a

Typical Installation
311882R 7
Typical Installation for Lubrication Applications
Key for F IG . 3
A Pump Air Regulator
B Air Line Lubricator
C Air Line Filter
D Bleed-Type Master Air Valve (required, for pump)
E Fluid Drain Valve (required)
F Bung Adapter
G Grounded Air Hose
H Grounded Fluid Hose
J Pump Fluid Inlet
K 1/4 npt(f) Pump Air Inlet
L 3/4 npt(f) Pump Fluid Outlet
F IG . 3: Typical Installation for Lubrication Applications
AB C D
E
F
H
J
J
K
L
G
01349
D

Installation
8311882R
Installation
System Accessories
To ensure maximum pump performance, be sure that all
accessories used are properly sized to meet your sys-
tem’s requirements. See Accessories, page 22.
Air Line Accessories
Install the following accessories in the order shown in
the Typical Installation for Lubrication Applications,
using adapters as necessary:
An air line lubricator (B) provides automatic air motor
lubrication.
A bleed-type master air valve (D) is required in your
system to relieve air trapped between it and the air
motor when the valve is closed (see the WARNING on
left). Be sure the bleed valve is easily accessible from
the pump, and is located downstream from the air regu-
lator.
An air line filter (C) to remove harmful dirt and moisture
from the compressed air supply.
A second bleed-type air valve (D) isolates the air line
accessories for servicing. Locate upstream from all
other air line accessories.
Fluid Line Accessories
A fluid drain valve (E) is required in your system to
relieve fluid pressure in the hose and gun (see the
WARNING on left). Install the drain valve so that it
points down and the handle points up when the valve is
opened.
A bleed-type master air valve (D) and a fluid drain
valve (E) are required in your system, to help reduce
the risk of serious injury, including splashing fluid in
the eyes or on the skin, and injury from moving parts
when you are adjusting or repairing the pump.
The bleed-type master air valve (D) relieves air
trapped between this valve and the pump after the
pump is shut off. Trapped air can cause the pump to
cycle unexpectedly and result in serious injury,
including amputation. Install the valve close to the
pump.
The fluid drain valve (E) helps relieve pressure in the
displacement pump, hose, and dispensing valve
when shutting off the pump. Actuating the dispensing
valve to relieve pressure may not be sufficient, espe-
cially if there is a clog in the hose or the dispensing
valve.

Setup
311882R 9
Setup
1. Apply thread sealant to the male threads of the air
needle valve (48) and the quick disconnect fitting
(49) and install. See F
IG . 4
2. Apply thread sealant to the male outlet fitting (not
supplied) and insert into the outlet port. See F
IG . 5.
3. Use labels (70) provided to identify the appropriate
pump for your material. See F
IG . 5.
4. Lubricate the bung adapter inside diameter and
mounting threads. Ensure the gasket is in place and
screw the bung adapter (51) securely into the bung-
hole of the drum. Insert the pump through the
adapter and lock it in place. See F
IG . 7.
F
IG . 4
F
IG . 5
WLD
48
49
1
Apply thread sealant
1
1
Apply thread sealant
1
1
1
F IG . 6
F
IG . 7
51
Lubricate threads
2
2

Setup
10 311882R
5. Install air line (3/8 in. (76 mm) ID minimum) with
quick disconnect air coupler (52) provided. See F
IG .
8.
Grounding the System
To reduce the risk of static sparking, ground the pump
and all other equipment used or located in the pumping
area. Check your local electrical code for detailed
grounding instructions for your area and type of
equipment. Ground all of this equipment.
1. Pump: Connect Ground Wire (Y) to grounding
screw (72) and tighten the screw securely. See F
IG .
9. Connect the other end of the wire to a true earth
ground. Make certain to comply with all National,
State, and Local Electrical Codes.
2. Air compressor: according to manufacturer’s recom-
mendations.
3. Fluid hoses: use only grounded hoses with a maxi-
mum of 300 ft (91 m) combined hose length to
ensure grounding continuity. Refer to Hose Ground-
ing Continuity.
4. Dispensing valve: grounding is obtained through
connection to a properly grounded fluid hose and
pump.
5. Object being sprayed: according to local code.
6. Fluid supply container: according to local code.
7. All solvent pails used when flushing, according to
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non–conductive sur-
face, such as paper or cardboard, which interrupts
the grounding continuity.
8. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
spray gun/dispensing valve firmly to the side of a
grounded metal pail, then trigger the gun/valve.
F
IG . 8
52
F IG . 9
WLD
Y
72

Operation
311882R 11
Operation
Pressure Relief Procedure
1. Engage trigger lock.
2. Close the bleed-type master air valve.
3. Disengage the trigger lock.
4. Hold a metal part of the dispense valve firmly to a
grounded metal pail. Trigger the valve to relieve
pressure.
5. Engage the trigger lock.
6. Open all fluid drain valves in the system, having a
waste container ready to catch drainage. Leave
drain valve(s) open until you are ready to dispense
again.
7. If you suspect the nozzle or hose is clogged or that
pressure has not been fully relieved after following
the steps above, VERY SLOWLY loosen the hose
end coupling to relieve pressure gradually, then
loosen completely. Clear hose or nozzle obstruc-
tion.
Flushing
1. Follow Pressure Relief Procedure, page 11.
2. Place suction tube in grounded metal drum contain-
ing cleaning fluid.
3. Set pump to lowest possible fluid pressure, and start
pump.
4. Hold a metal part of the dispense valve firmly to a
grounded metal pail. Trigger the dispense valve
until clean solvent dispenses.
5. Remove valve from hose.
6. Follow Pressure Relief Procedure, and remove
fluid filter and soak in solvent. Replace filter cap.
Daily Startup
1. Verify that the air needle valve is closed.
2. Connect the air line quick disconnect coupler to the
transfer pump
3. Turn on the main air supply.
4. Slowly open the air needle valve until the transfer
pump runs slowly.
5. Use the air needle valve to control the pump speed.
Daily Shutdown
1. Disconnect air line coupler.
2. When air pressure is bled off, close the air line nee-
dle valve.
Trapped air can cause the pump to cycle unexpectedly,
which could result in serious injury from splashing or
moving parts.
Trapped air can cause the pump to cycle unexpectedly,
which could result in serious injury from splashing or
moving parts.
• Flush at the lowest pressure possible. Check
connectors for leaks and tighten as necessary.
• Flush with a fluid that is compatible with the
fluid being dispensed and the equipment wetted
parts.
Caution
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed and could cause personal injury and/or dam-
age to the pump. If the pump accelerates quickly or
starts running too fast, stop it immediately and check
the fluid supply. If the supply container is empty or air
has been pumped into the lines, refill the container
and prime the pump and the lines with fluid, or flush
and leave it filled with a compatible solvent. Be sure to
eliminate all air from the fluid system.
Do not attempt to operate pump unless it is securely
mounted in a drum.

Air Motor Repair
12 311882R
Air Motor Repair
1. Remove cap (1), cylinder (4), and square gaskets
(3*). Inspect all parts, including spring under cap
(not shown in F
IG . 10) for damage and replace if
necessary. See F
IG . 10. Unscrew by hand or use a
chain wrench to prevent distortion of the cylinder’s
shape.
NOTE: Series A air motors have thin, flat, white
seals in air valve. Series B air motors have thicker
black seals in the air valve.
2. Series A air motors only: Loosen set screw (18) and
unscrew air valve (5). If necessary to assist turning,
wedge a screwdriver blade between the screw
heads and the hex cap of air valve (5). Discard
items 5, 13, 15, and 18. See F
IG . 11.
3. Series B air motors only: Unscrew air valve (5). If
necessary to assist turning, wedge a screwdriver
blade between the screw heads and the hex cap of
the air valve (5). Inspect o-rings (13* and 15*) for
damage and replace if necessary. Ensure o-ring
(13*) is correctly positioned and not pinched. See
F
IG . 12.
CAUTION
Air valve assembly has changed to series B for
improved performance. Parts are not interchangeable
between series A and B air motor. Series A air valves
can be upgraded to series B with kit 262042.
F
IG . 10
WLD
1
*3
*3
4
F IG . 11: Series A Air Valve
F
IG . 12 Series B Air Valve
WLD
5
*13
*15
18
WLD
5
*13
*15

Air Motor Repair
311882R 13
4. Align slot of shield (75) with piston hole and place
pin tool (69) in piston hole to prevent piston from
turning. Use second pin tool (69) to unscrew piston
cap (17) and separate from piston (21) to expose
dowel pin (19). See F
IG . 13.
5. Series A air motors only: Remove dowel pin (19)
and take piston cap (17) off transfer shaft (20). Dis-
card items 17, 19, 50. See F
IG . 14.
6. Series B air motors only: Remove dowel pin (19)
and take piston cap (17) off transfer shaft (20).
Remove o-ring (50*) from piston cap. Inspect all
parts for damage. See F
IG . 15.
7. Slide air piston (21) out the top of the air motor base
(23). Remove o-ring (24*) from air motor base.
Inspect all parts, including the spring (22) in the air
motor base, for damage. See F
IG . 16.
F
IG . 13
F
IG . 14
WLD
21
69
69
17
19
75
WLD
19
*50
17
20
F IG . 15
F
IG . 16
WLD
19
*50
17
20
WLD
21
22
23
*24

Pump Lower Repair
14 311882R
Pump Lower Repair
1. Use a chain wrench near the top of the suction tube
at the point indicated in F
IG . 17, and a wrench on
the flats of the foot valve (45) to loosen the foot
valve from the suction tube (44). To prevent dam-
age to the suction tube, do not remove the foot
valve until instructed to do so in step 3.
2. With the foot valve still in place to support the suc-
tion tube, use a chain wrench near the bottom of the
suction tube at the point indicated in F
IG . 18, to
loosen the suction tube (44) from the pump body
(34).
3. Remove the foot valve assembly from the suction
tube (44).
4. Remove retaining ring (46), snap ring (47), ball (71),
and o-ring (38*) from foot valve (45). Inspect all
parts for damage. See F
IG . 18.
5. Remove suction tube (44) from pump body (34).
See F
IG . 19.
6. Inspect o-ring (38) on pump body and suction tube
for damage. See F
IG . 19.
7. Pull transfer shaft (20) out the bottom of pump body
(34). See F
IG . 20.
F
IG . 17
NOTE: When removing the suction tube, be
very careful not to bend, dent, or damage it. To
avoid damage, use the chain wrench only at the
top and bottom of the suction tube as indicated
in F
IG . 17 and F IG . 18. Do not apply the wrench
to the middle of the suction tube.
F
IG . 18
44
Apply chain wrench
approximately here
ti9903
46
47
71
*38
45
Apply chain wrench
approximately here
44
F IG . 19
44
ti9976
38
34
Apply chain wrench
approximately here

Pump Lower Repair
311882R 15
8. Remove pin (56). Remove piston valve assembly.
Unscrew piston valve (43) from piston housing (53).
Remove wear ring (41*), u-cup (40*) and ball (42).
Inspect all parts for damage. See F
IG . 21.
9. Remove pins (55). See F
IG . 22.
10. Loosen set screw (37) from collar (36). Remove col-
lar from piston housing (54). Remove u-cup (35*).
Inspect all parts for damage. See F
IG . 23.
F
IG . 20
F
IG . 21
ti9905
20
34
ti9904b
56
*40
*41
42
43
53
Lip up
F IG . 22
NOTE: Series A and B pumps were equipped
with springs pins. In Series C pumps, these
pins were replaced with a solid clevis
pin (55, 56).
F
IG . 23
55
54
74
r_311880_14e_fig21
36
35
55
37
36
*35
54
Lip down
r_311882_14e_fig22

Pump Lower Repair
16 311882R
11. Unscrew mounting flange (26) from pump body
(34). Remove o-ring (32*) and PTFE gasket (33*)
from pump body (34). Inspect all parts for damage.
See F
IG . 24.
12. Align slot of shield (75) and insert pin (69) to remove
hex nut (27) from mounting flange (26). Remove
female gland (30*), 2 PTFE packings (29*), male
gland (28*) and wiper (31*). Inspect all parts for
damage. See F
IG . 26.
13. Unscrew three fasteners (60) to remove the flange
(26) and tie-rods (25). Slide the guard (75) out.
Unscrew the tie rods (25) using the wrench flats at
the bottom.
F
IG . 24
WLD
26
*33
*32
34
F IG . 25
WLD
75
60
26
25
F IG . 26
WLD
Seal stack enlarged
to show detail.
27
*30
*29
*28
*31
69
75

Reassembly
311882R 17
Reassembly
To reassemble the pump lower and air motor, reverse
the steps on the preceding pages. Follow the torque
requirements listed in the Parts - Model 295616 draw-
ing on page 20.
Troubleshooting
NOTE: See Air Motor Repair, step 3 and step 4
(F
IG . 12) for special notes on reassembly.
Problem Cause Solution
The pump fails to operate Dirty or worn air motor. Clean, service
Inadequate air supply or restricted
lines.
Clean lines or increase the air supply
(see Technical Data).
Closed or clogged air valves. Open or clear the valves.
Clogged fluid hose or valve. Clear the hose or valves
Worn or damaged valves or seals. Service the valves or seals.
The pump operates, but the output is
low on both strokes.
Clogged fluid hose or valve. Clear the hose or valves.
Exhausted fluid supply. Refill the fluid supply and reprime the
pump.
Worn or damaged valves or seals. Service the valves or seals.
The pump operates, but the output is
low on the downstroke.
Held open or worn intake valve. Clear or service the valve.
Worn or damaged valves or seals. Service the valves or seals.
The pump operates, but the output is
low on the upstroke.
Held open or worn piston valve. Clear or service the valve.
Worn or damaged valves or seals. Service the valves or seals.
Erratic or accelerated operation. Exhausted fluid supply. Refill the fluid supply and reprime the
pump.
Broken air motor compression spring. Replace the spring.
Pump slowly moves after fluid shutoff
in downstroke.
Clogged or dirty intake valve check
ball.
Clean ball and seat.
Worn or damaged valves or seats. Install repair kit.
Pump slowly moves after fluid shutoff
in upstroke.
Clogged or dirty lower piston ball or
seat.
Clean ball and seat.
Worn or damaged valves or seats. Install repair kit.

Troubleshooting
18 311882R

Troubleshooting
311882R 19

Parts - Model 295616
20 311882R
Parts - Model 295616
WLD
3*
4
2
*3
1
*
✿ 13
✿ 5
15*
*32
*28
*29
*30
27
25
24*
23
22
21
*33
60
53
56✓
37
36
39
34
42✓
43
44
46
47
71✓
38✓
45
41✓
40✓
❄ 54
38✓
31*
26
72
51b
51c
✓51a
51
Bung Adapter
Lubricate all o-rings and seals before and after assembly
Torque to 45-55 ft-lbs (61-74.5 N•m)
Torque to 30-40 ft-lbs (40.6-54.2 N•m)
Torque to 15-20 ft-lbs (20.3-27.1 N•m)
Torque to 10-12 ft-lbs (13.5-16.3 N•m)
Torque to 110-120 in-lbs (12.3-13.4 N•m)
Torque to 20-30 in-lbs (2.2-3.3 N•m)
Torque to 50-60 in-lbs (5.6-6.7 N•m)
Tighten 1/8 to 1/4 turn past finger-tight
1
2
3
4
5
6
7
8
9
2
3
4
5
6
8
9
5
6
4
8
4
7
74 ❄
73✓
35✓
✿ 19 17
✿
* ✿ 50
❄ 20
✓51h
❄ 55
75