Grandstream Networks BroadWorks BroadSoft GXW-400X Manual

Grandstream Networks Page 1 of 3
PEER – PEER GATEWAY SCENARIO
(Extending Analog Lines Using the GXW Series w/o SIP Server)
Boston, MA Branch
4 employees
Headquarters
–
Denver CO
Multiple employees
I
In nt te er rn ne et t
C
Cl lo ou ud dGXW 400x
GXW 410x
Analog Phones
P
PS ST TN N
C Cl lo ou ud d
T
Tr ra ad di it ti io on na al l
P
PB BX X
FX0 Lines
FX0 Lines
EXTENDING ANALOG LINES OVER IP
USING
GXW410X FXO GATEWAY &GXW400X FXS GATEWAY
This is a popular scenario which does not involve any SIP Server or IP PBX. This scenario allows an organization
with a remote location to access the local FXO trunks (Traditional PBX trunks or PSTN lines) through the IP network.
In the diagram, remote users in Boston have standard analog phones connected to the GXW400x FXS Analog
Gateway, while corporate users in the Denver location use a traditional PBX whose FXO trunks are connected to a
GXW410x FXO Analog Gateway. With the help of the IP infrastructure and Grandstream GXW FXO and FXS Series,
the remote users in Boston are able to make, as well as receive calls from Denver as if they were at the same
location.
NOTE:Please upgrade the firmware of the GXW4004 to 1.0.0.39 version or higher (point the device to
168.75.215.189 OR by downloading the firmware from www.grandstream.com and upgrading locally using TFTP or
HTTP) and upgrade the firmware of the GXW410x to 1.0.0.53 version or higher (available at
www.grandstream.com/).
Peer – Peer Gateways (w/o SIP Server)

Grandstream Networks Page 2 of 3
Peer – Peer Gateways (w/o SIP Server)
CONFIGURATION OF THE GXW410X &GXW400X SCENARIO
Configure the following settings for each of the devices using the Grandstream Web Configuration pages for each
device.
GXW400x GXW410x
Profile 1
•SIP Server - Set to IP Address of GXW410x
•SIP Registration - No
•Outgoing Call without Registration - Yes
•NAT traversal – No
Advanced Settings
•STUN Server - Blank
•Use Random Port - No
Advanced Settings
•STUN Server - Blank FXO lines •Wait for Dial Tone - Y or N (whichever
suits your FXO lines)
•Stage Method - 1
•Off-hook Auto Dial -
444 @ch1-8:p1; ch1-8:5060++
Channels
•Channel - 1
•SIP User ID - 5060
•Profile ID - Profile 1
•Local SIP Listen port - 5060++
Profile 1
•SIP Server - Set it to IP Address of
GXW400x
•SIP Registration - No
•NAT traversal - No
NOTE:In order for this setup to work, it is extremely important that both gateways (GXW410x and GXW400x) are
located on the same LAN OR Public Static IPs. In short, the GXWs should be able to locate each other.

Grandstream Networks Page 3 of 3
ONE TO ONE MAPPING BETWEEN FXS PORT AND FXO PORTS
If your setup requires that FXS port ‘x’ user be able to access only FXO port ‘x’ for outbound calls, use this setting
under Channels Webpage on the GXW410x.
By default the value is 99.
This setting allows you the power to send an outbound call to a specific FXO line.
For example:
Bob is in the Boston office (GXW400x) on FXS port 1 and he needs to make an outbound call to Alice in the Denver
office on extension 566-9300 through FXO port 1. Bob needs to dial 99-1-566-9300, which forces the call to go
through FXO line 1 only. (99 represents the prefix; 1represents port number 1)
Since the FXS gateway has a Dial Plan feature, you can configure all calls to have a prefix (such as 99) appended
automatically so Bob could just dial 1-566-9300 and the FXS gateway would append 99 to it before dialing.
PORT TO PORT MAPPING BETWEEN FXS PORT AND FXO PORT
Port to port mapping enables calls placed on a specific FXS port n to be completed through the PSTN network that is
connected to a specific FXO port n. This is similar to a one to one mapping configuration except it is hard coded to
always be routed through a specific FXO port. End-user is not required to dial any extra numbers (see above
example).
Port to port mapping is configured using the Dial Plan feature on the FXS GXW. The FXS GXW400x supports $P, $p
as port numbers. Port to port mapping from the GXW400x to GXW410x is configured as follows:
GXW4108: prefix to specific port: 99 ---- default settings on FXO GXW
GXW4008: dial plan: { <=99$P>x+ }
So, if the GXW4008 is configured with this dial plan, any number dialing from a specific port will be prefixed with 99
and a port number.
For example: if you dial [phone] from your phone (which is connected to port 5), the number is appended with
the appropriate dial plan (the actual dialed number will be 9956171234567). On the GXW4108 gateway (with this
configuration), it will route the call to port 5 and strip off 995 and send the call over the PSTN network.
Important Note: This pair of GXWs should be configured with the one-stage dialing method.
For example:
Bob is in the Boston office (GXW400x). His phone is connected to FXS port 5. He needs to make an outbound call
to Alice who lives in Denver with phone number XXX-566-9300. Bob dials the number XXX-566-9300. The call is
seamlessly mapped through FXO port 5 (which was pre-configured using the dial plan - 995).
If you need further information or have any questions related to this setup, please email us at [email protected].
Peer – Peer Gateways (w/o SIP Server)