Granite 67243-75 User manual

67243-75
MULTI MOVER
WITH FOLD DOWN REAR WHEELS
INSTRUCTION MANUAL
Revised: JULY 2017

2
CONTENTS
Specs......................................................................3
Parts Diagram ........................................................4
Assembly.............................................................5-7
TOOLS NEEDED
• 3/4” Wrench
• Ratchet with 3/4” Socket
• Needle Nose Pliers
• Box Cutters / Utility Knife
STANDARD ON ALL
AMERICAN CART PRODUCTS
Made in the USA
Hand crafted at our Ohio plant.
Heavy-duty comes standard
American Carts are all built to heavy duty specs
Flat-free tires
10 inch closed-cell tires that will never go flat
Powder coated nish
Protects the steel and provides a lasting finish
D-Brackets
One piece design holds the axle in place and
supports the load
Steel construction
Built from American sourced steel
Easy to operate
Designed to get work done with less muscle
strain and simple operation
WARRANTY
3 Year Limited Warranty. Carts, excluding any
finishes, casters and wheels are warranted for three
(3) years from date of original purchase. Casters
and wheels are warranted for 90 days from date of
original purchase. We will repair, without charge,
any defect due to faulty material or workmanship.
These warranties do not cover failures due to
abuse, misuse, improper installation, accidental
damage or when repairs or modifications have been
made or attempted to be made by anyone other
than Granite Industries. Any defective products
that meet warranty specifications and Granite
Industries approval, may be returned to the factory
to be repaired or replaced free of charge. (Granite
Industries will pay to ship replacement item(s) to the
customer; however the customer is responsible for
shipment of products to the factory.) This remedy
is the sole remedy in contact, tort or otherwise,
and Granite Industries is not liable for incidental,
consequential or special damages. These warranties
give you specific legal rights, and you may have
other rights which vary from state to state. Should
you have any questions, contact Granite Industries
(Proof of purchase may be required).
Customer Service
877-447-2648
M-F, 8am - 5pm EST

3
SPECS
Overall Dimensions: W: 24” D: 51” H: 36”
Foot Plate: W: 23” D: 17”
Weight: 84 lbs. Capacity: 750 lbs.
*Measurements taken on 4 wheels with folding foot plate open

4
ITEM NO QTY PART NO DESCRIPTION
1 1 MI-12-4618 MULTI MOVER CART BODY
2 4 PI-06-0115 10” STEEL HUB WHEEL
3 2 06003 2” SNAP PIN
4 4 PI-01-0226 1-1/4” COTTER PIN
5 2 PI-01-0121 1/2” NUT USE 3/4” WRENCH/SOCKET
6 2 PI-01-0043 1/2” HEX BOLT (1-1/2” L) USE 3/4” WRENCH/SOCKET
7 4 PI-01-0451 3/4” WASHER
8 1 MI-12-5037 REAR AXLE ASSEMBLY
PARTS DIAGRAM

5
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
1 1 Multi Mover Cart Body
2 2 10” Flat Free Steel Hub Wheel
4 2 1-1/4” Cotter Pin
7 2 3/4” Washer
TOOLS
Needle Nose Pliers
Slide the washer onto the axle.
STEP 1: FRONT WHEEL ASSEMBLY
1
Insert the wheels onto the front axle located
towards the bottom of the Multi Mover. The
offset side of the wheel should be facing the
cart body.
Insert the cotter pin and secure it by
bending both ends outward with a
needle nose pliers.
P
CHECK POINT
Your cart should look like this.
If so, continue onto the next step.

6
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
3 2 2” Snap Pin
5 2 1/2” Nut
6 2 1/2” Hex Bolt (1-1/2”L)
8 1 Rear Axle Assembly
TOOLS
3/4” Wrench
3/4” Socket
Insert the bolts through the cart body and
rear axle assembly. Install the bolts and
tighten with a 3/4” wrench and ratchet.
STEP 2: REAR AXLE ASSEMBLY
1
Place the rear axle assembly over the frame.
The flat side should be against the cart
body, the flanges should face up.
Insert the snap pins into the rear axle
assembly. Adjust the position to
suit your needs.
P
CHECK POINT
Your cart should look like this.
If so, continue onto the next step.

7
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
1 1 Multi Mover Cart Body
2 2 10” Flat Free Steel Hub Wheel
4 2 1-1/4” Cotter Pin
7 2 3/4” Washer
TOOLS
Needle Nose Pliers
Slide the washer onto the axle.
STEP 3: REAR WHEEL ASSEMBLY
1
Insert the wheels onto the rear wheel
assembly. The offset side of the wheel
should be facing the cart body.
Insert the cotter pin and secure it by
bending both ends outward with a
needle nose pliers.
Your Multi Mover with Rear Wheels
is now fully assembled.

GRANITE INDUSTRIES
595 EAST LUGBILL ROAD
877-447-2648
[email protected]
8