Granite American Cart & Rack 67283 User manual

67283
CHURCH CHAIR CART
INSTRUCTION MANUAL
Revised: JULY 2017

2
CONTENTS
Specs......................................................................3
Parts Diagram ........................................................4
Assembly................................................................5
TOOLS NEEDED
• Needle Nose Pliers
• Box Cutters / Utility Knife
• Wrenches: 9/16” & 3/4”
• Sockets: 9/16” & 3/4”
WARRANTY
3 Year Limited Warranty. Carts, excluding any
finishes, casters and wheels are warranted for three
(3) years from date of original purchase. Casters
and wheels are warranted for 90 days from date of
original purchase. We will repair, without charge,
any defect due to faulty material or workmanship.
These warranties do not cover failures due to
abuse, misuse, improper installation, accidental
damage or when repairs or modifications have been
made or attempted to be made by anyone other
than Granite Industries. Any defective products
that meet warranty specifications and Granite
Industries approval, may be returned to the factory
to be repaired or replaced free of charge. (Granite
Industries will pay to ship replacement item(s) to the
customer; however the customer is responsible for
shipment of products to the factory.) This remedy
is the sole remedy in contact, tort or otherwise,
and Granite Industries is not liable for incidental,
consequential or special damages. These warranties
give you specific legal rights, and you may have
other rights which vary from state to state. Should
you have any questions, contact Granite Industries
(Proof of purchase may be required).
Customer Service
877-447-2648
M-F, 8am - 5pm EST
To view more products from
American Cart & Rack
scan the QR code with your phone
or visit AmericanCartAndRack.com

3
SPECS
Overall Dimensions: W: 25” D: 53” H: 61”
Overall Dimensions:* W: 25” D: 54” H: 50”
Weight: 53 lbs. Capacity: 500 lbs.
*Measurements taken on 4 wheels

4
ITEM NO QTY PART NO DESCRIPTION
1 2 PI-06-0124 10” Plastic Hub Flat Free Offset Tire
2 1 MI-12-4751 Cart Chassis
3 1 MI-12-4752 Rear Caster Mount
4 1 MI-12-4753 Chair Lifting Bar
5 2 PI-01-0226 1/8” x 1 1/4” Cotter Pin
6 2 PI-01-0451 3/4” Washer
7 2 38057 5” Caster with 1 1/4” Stem
8 1 PI-06-0044 4” Caster with Rubber Tread
9 1 MI-01-5830 Chair Stop Bar
10 10 PI-01-0019 3/8” Locknut
11 1 PI-01-0059 1/2” Washer
12 1 PI-01-0068 1/2” Lock Washer
13 1 PI-01-0067 1/2” Nut
14 10 PI-01-0100 3/8” Hex Bolt
15 8 PI-04-0036 Cap Plug 1 1/4”
PARTS DIAGRAM

5
3
2
COMPONENTS
ITEM NO QTY DESCRIPTION
2 1 Cart Chassis
7 2 5” Caster with 1 1/4” Stem
14 4 3/8” Hex Bolt
10 4 3/8” Locknut
TOOLS
9/16” Wrench
9/16” Socket
Secure in place using a 3/8” hex bolt and
lock nut. Repeat this for the remaining three
bolts.
STEP 1: REAR WHEEL ASSEMBLY
1
Position the rear caster mount onto the
cart chassis as shown. The lower part of the
mount will connect to the lowest set of holes
on the chassis.
Insert the casters into the rear caster
mount and pin into place.
P
CHECK POINT
Your cart should look like this.
If so, continue onto the next step.