Granite American Cart & Rack Titan II User manual

67106-75
TITAN II APPLIANCE CART
WITH FOLD DOWN REAR WHEELS
INSTRUCTION MANUAL
Revised: JULY 2017

2
CONTENTS
Specs......................................................................3
Parts Diagram ........................................................4
Setup......................................................................5
TOOLS NEEDED
• Box Cutters / Utility Knife
WARRANTY
3 Year Limited Warranty. Carts, excluding any
finishes, casters and wheels are warranted for three
(3) years from date of original purchase. Casters
and wheels are warranted for 90 days from date of
original purchase. We will repair, without charge,
any defect due to faulty material or workmanship.
These warranties do not cover failures due to
abuse, misuse, improper installation, accidental
damage or when repairs or modifications have been
made or attempted to be made by anyone other
than Granite Industries. Any defective products
that meet warranty specifications and Granite
Industries approval, may be returned to the factory
to be repaired or replaced free of charge. (Granite
Industries will pay to ship replacement item(s) to the
customer; however the customer is responsible for
shipment of products to the factory.) This remedy
is the sole remedy in contact, tort or otherwise,
and Granite Industries is not liable for incidental,
consequential or special damages. These warranties
give you specific legal rights, and you may have
other rights which vary from state to state. Should
you have any questions, contact Granite Industries
(Proof of purchase may be required).
Customer Service
877-447-2648
M-F, 8am - 5pm EST
To view more products from
American Cart & Rack
scan the QR code with your phone
or visit AmericanCartAndRack.com

3
SPECS
Overall Dimensions: W: 26” D: 48” H: 49”
Foot Plate: W: 26” D: 5”
Weight: 80 lbs. Capacity: 600 lbs.
*Measurements taken with the cart on 4 wheels.
0.003" - 0.005"
CATALOG NO.
SIZE DWG. NO.
ECO #
DRAWN
REDRAWN
WEIGHT, LBS
DO NOT SCALE DRAWING
PAINT THICKNESS
FINISH
MATERIAL
ANGLES
DECIMALS
.005
1/32" .00 .01 1
.000
FRACTIONS
TOLERANCES ARE:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
APPROVALS DATE
DO NOT MANUALLY UPDATE
Granite Industries Inc.
REMOVE ALL BURRS, SHARP EDGES AND CORNERS
CAD GENERATED DRAWING,
REV.
.
.
.
67106-75
AGR 5/20/15
12/28/1799
49°
.
.
.
PARTS LIST
.
-
4 15/16"
15 3/4"
60"
26"
17 1/2"
48 5/8"
47 3/8"
ITEM NO. Default/
QTY. PART NUMBER DESCRIPTION
1 1 67101-75 24"X60" APPLIANCE CART MADE IN USA
2 1 MI-12-2081 CART 67106
3 2 MI-04-0068 BAR RD HR 3/8" x 8"
4 2 PI-14-0001 G-PIN SPRING
5 2 PI-01-0004 PIN-ROLL 3/16" x 1"
6 2 PI-04-0104 1" Square Tube Cap - black
7 1 MI-04-0493 BAR RD CR 1/2" x 18 1/2"
8 6 PI-01-0002 WASHER-USS FLAT 1/2" PLATED
9 2 PI-01-0073 PIN-COTTER 5/32" x 3/4"
10 2 PI-06-0044 SSC-4 RUBBER MOLD ON TREAD
11 2 PI-01-0068 WASHER-LOCK 1/2" PLATED
REVISIONS
REV. DESCRIPTION DATE BY

4
ITEM NO QTY PART NO DESCRIPTION
1 1 67101 CART 67101
2 1 MI-12-2081 WELDMENT FOLD OUT
WHEELS
3 2 MI-04-0068 BAR RD HR 3/8” x 8”
4 2 PI-14-0001 G-PIN SPRING
5 2 PI-01-0004 PIN-ROLL 3/16” x 1”
6 2 PI-04-0104 1” Square Tube Cap - black
7 1 MI-04-0493 BAR RD CR 1/2” x 18 1/2”
8 6 PI-01-0002 WASHER-USS FLAT 1/2” PLATED
9 2 PI-01-0073 PIN-COTTER 5/32” x 3/4”
10 2 PI-06-0044 SSC-4 RUBBER MOLD ON
TREAD
11 2 PI-01-0068 WASHER-LOCK 1/2” PLATED
2 PI-06-0115 10” WHEEL WITH STEEL HUB
PARTS DIAGRAM

5
3
2
Swing the support bar downwards.
REAR WHEEL SETUP
1
Pull the spring loaded lock down located on
the back of the cart that holds the support
bar in place.
Lift up on the rear wheel assembly.
4
Pull the locking pin back on the support
bar, and secure it onto the lower axle of
the cart. Be sure it locks back into place.

6
3
2
Slide the strap under the center roller.
TIE STRAP SETUP
1
Lift the center roller.
Lower the center roller and insert the strap
back through, this time going above the
roller.
4
Your strap should now lock in place when
tightened.

NOTES:
7

8
GRANITE INDUSTRIES
595 EAST LUGBILL ROAD
877-447-2648
[email protected]