GRAPHTEC midi LOGGER GL240 User manual

USER’S MANUAL
MANUAL NO.GL240-UM-153
GL240

i
To Ensure Safe and Correct Use
To Ensure Safe and Correct Use
•To ensure safe and correct use of the GL240, read this manual thoroughly before use.
•After having read this manual, keep it in a handy location for quick reference as needed.
•Do not permit small children to touch the GL240.
•The following describes important points for safe operation. Please be sure to observe them strictly.
Conventions Used in This Manual
To promote safe and accurate use of the GL240 as well as to prevent human injury and property damage,
safety precautions provided in this manual are ranked into the ve categories described below. Be sure you
understand the difference between each of the categories.
DANGER This category provides information that, if ignored, is
highly likely to cause fatal or serious injury to the operator.
WARNING This category provides information that, if ignored, is
likely to cause fatal or serious injury to the operator.
CAUTION This category provides information that, if ignored, could
cause physical damage to the GL240.
HIGH
TEMPERATURE
This category provides information that, if ignored, is
likely to cause burns or other injury to the operator due to
contact with high temperature.
ELECTRICAL
SHOCK
This category provides information that, if ignored, is
likely to expose the operator to electrical shock.
Description of Safety Symbols
The symbol indicates information that requires careful
attention (including warnings). The specic point requiring
attention is described by an illustration or text within or next to
the symbol.
The symbol indicates an action that is prohibited. Such
prohibited action is described by an illustration or text within or
next to the symbol.
The symbol indicates an action that must be performed.
Such imperative action is described by an illustration or text
within or next to the symbol.

ii
Safety Precautions
Safety Precautions
WARNING
Before turning on the GL240, ensure that the electric
socket’s supply voltage conforms to the GL240’s
power rating.
•Use of a different supply voltage may cause damage to the
GL240 or a fire hazard due to electrical
shock or current leakage.
If the GL240 generates smoke, is too hot, emits a
strange odor, or otherwise functions abnormally,
turn off its power and unplug its power cord from the
electrical socket.
•Use of the GL240 in such status may result in a fire hazard
or electrical shock.
•After checking that smoke is no longer being generated,
contact your sales representative or nearest Graphtec
vendor to request repair.
•Never try to perform repair yourself.
Repair work by inexperienced
personnel is extremely dangerous.
Never disassemble or remodel the GL240.
•Such action may cause a fire hazard due to electric shock
or current leakage.
•Contact with a high-voltage component inside the GL240
may cause electric shock.
•If repair is required, contact your
sales representative or nearest
Graphtec vendor.
Be sure to securely connect the GL240's GND
terminal.
•After checking that the power switch is turned off, connect
the power cord’s female plug to the GL240 and then
connect its male plug into the electrical socket.
•For grounding, use a ground wire with a diameter of at least
0.75 mm2. When using the GL240 in an environment where
grounding is not
possible, ensure measured is no greater than 50 V (DC or
rms).
Avoid using the GL240 in extremely dusty or humid
places.
•Such use may cause a fire hazard due to electrical shock or
current leakage.
Avoid using the GL240 in places where it may be
exposed to water such as bathrooms, locations
exposed to wind and rain, and so on.
•An electrical shock or fire may be caused due to current
leakage.
Prevent dust or metallic matter from adhering to the
power supply connector.
•Adhesion of foreign matter may cause a fire hazard due to
electrical shock or current leakage.
Never use a damaged power cord.
•Use of a damaged cord may result in a fire hazard due to
electrical shock.
•If the cord becomes damaged, order a new one to replace
it.
Use prohibited
Use prohibited
Use prohibited No disassembly
Watch out for
electrical shock
Use prohibited Watch out for
electrical shock
Watch out for
electrical shock
Avoid water
Unplug the power
cord from the socket

iii
Safety Precautions
Safety Precautions
CAUTION
If uid or foreign matters enters inside the GL240, turn
off the power switch and disconnect the power cord
from the electrical socket.
•Use in such status may cause a fire hazard due to electrical
shock or current leakage.
•Contact your sales representative or
nearest Graphtec vendor to request
repair.
To insert or disconnect the power cord or a signal
input cable, grasp the power cord’s plug or the signal
input cable’s connector.
•Pulling the cord/cable itself damages the cord/cable,
resulting in a fire hazard or electrical shock.
Do not use the GL240 in a location subject to
excessive mechanical vibration or electrical noise.
•Such location may impair the GL240’s performance.
Do not place the receptacles containing uid onto this
device or close to this device.
•Fluid spilling inside the GL240 may cause a fire hazard due
to electrical shock or current leakage.
Do not use the AC power supply and the DC power
supply other than the specied supply voltage for this
device.
•Such action may cause a fire hazard due to electric shock
or current leakage.
Do not use or store the GL240 in a location exposed to
direct sunlight or the direct draft of an air conditioner
or heater.
•Such location may impair the
GL240’s performance.
Do not attempt to lubricate the GL240’s mechanisms.
•Such action may cause the GL240 to break down.
Never clean the GL240 using a volatile solvent (such
as thinner or benzine).
•Such action may impair the GL240’s performance.
•Clean off any soiled areas using a soft dry cloth.
Use prohibited
Use prohibited Use prohibited
Use prohibited
Use prohibited
Use prohibited
Watch out for
electrical shock
Avoid water
Unplug the power
cord from the socket
Be sure to use the Graphtec-supplied AC adapter.
•It will damage this device.
Use prohibited

iv
Safety Precautions
Safety Precautions
CAUTION
Do not touch the device with wet hands.
•This can cause an electrical shock or malfunction.
Conrm the power of supplier of signal is turned
off before connecting the input cables to the input
terminal of this device to prevent the electric shock.
•It will cause the electric shock.
Be careful of static electricity.
•Static electricity may damage the device. To prevent this
from happening, touch a different metal object to discharge
any built-up static electricity before touching the GL240.
Do not touch the input terminals after the signal
cable is connected to the measuring objects that are
containing the voltage.
•It will cause the electric shock.
•Ensure that the GL240’s power source is positioned so that
it can easily be disconnected.
Do not input the voltage that is exceeding the
specication of this device.
•If a voltage exceeding the specified value is input, the
semiconductor relay in the input section will be damaged.
Never input a voltage exceeding the specified value even
for a moment.
•Have an enough margin from the specification of
withstanding voltage when using this device, it have to
consider a noise and change of the measurement voltage.
•It will cause the fire or the electric shock when the voltage is
input to the defective device.
Do not block the air vent on the GL240.
•This device will get damage when there is abnormal heat in
this device.
Conrm this device is not broken before the input
cable is connected to the input terminal.
•It will cause the fire or the electric shock when the voltage is
input to the defective device.
Strict observance
Strict observance
Strict observance
Use prohibited
Don't touch
with wet hands CAUTION
CAUTION
Use prohibited
HIGH
TEMPERATURE
Watch out for
electrical shock
Strict observance
Watch out for
electrical shock

v
Safety Precautions
Safety Precautions
CAUTION
When using the wireless LAN unit (optional), please
note the following:
•Turn off the device in places where wireless radio signal
use is restricted, such as on aircrafts and in hospitals. The
device can have an effect on electronic devices, medical
devices, etc., and may cause malfunctions.
When using the wireless LAN unit (optional) in a
medical establishment, please note the following
rules:
•Please turn off the power of this product in hospital wards.
•Each medical institution has its own usage prohibitions in
various areas. Be sure to follow these.
When using the wireless LAN unit (optional), please
note the following:
•In the event that the device has an effect on automatic
electronic devices such as cars or elevators, immediately
turn off the GL240.
When using the wireless LAN unit (optional), please
note the following:
•
If you have an implantable pacemaker or implantable
defibrillator installed, radio signals from the device may have
an effect on the operation of your implantable pacemaker or
implantable defibrillator.
This GL240 is not meant for use with lifesaving devices or devices with mission-critical high reliability or
high safety requirements (medical devices, aerospace devices, shipping devices, nuclear power devices,
etc.). In the event that this GL240 causes injury or property damage when used under these circumstances,
the maker assumes absolutely no responsibility and is not liable.
Do not use the device in any way not specied in this
manual. There is a danger that protective provisions
will have not been put in place.
The module connection terminal is for use only with
separately sold sensors and modules. Do not connect
any other devices. Doing so may damage the GL240.
Strict observance
Strict observance
Use prohibited
Use prohibited
Use prohibited
Use prohibited

I
Introduction
Introduction
Thank you for purchasing the GL240 midi LOGGER.
Please read this manual thoroughly before attempting to use your new product to ensure that you use it correctly
and to its full potential.
Notes on Use
Be sure to read all of the following notes before attempting to use the GL240 midi LOGGER.
1. Note on the CE Marking
The GL240 midi LOGGER complies with the following standards.
• EN 61326-1 Class A standard based on the EMC directive (2014/30/EU)
• EN 61010-1:2010 3rd standard based on the LVD directive (2014/35/ EU)
• EN 301 489-17/-1, EN 300 328 standards based on the R&TTE directive (1999/5/EC)
Although the GL240 complies with the above-mentioned standards, be sure to use it correctly in accordance
with the instructions and notes provided in this manual.
Moreover, use of the GL240 by incorrect procedures may result in damage to the GL240 or may invalidate its
safeguards. Please conrm all of its notes regarding use and other related information to ensure correct use.
2. Warning
This is a Class A product according to the EMC directive. In a domestic environment, this product may cause
radio interference or may be affected by radio interference to the extent that proper measurement cannot be
performed.
3. Notes on Radio Law
When using the GL240 midi LOGGER in the wireless LAN unit (optional), please note the following:
Do not remove the technical standards compliance label. Do not use the device if it does not have a label
on it.
This GL240 uses the 2.4GHz frequency band.
The following devices and transmitters use the same frequencies and should not be used near this GL240:
• Microwave ovens
• Pacemakers and other industrial, science, and medical devices
• Radio transmitters used in mobile body identication devices on factory production lines, etc. (transmitters
requiring licensing)
• Specied low-power radio transmitters (transmitters not requiring licensing)
Communications may become slower or impossible due to radio interference.
The signal may be weak or communications may become slower or impossible depending on the
circumstances this GL240 is used in. Take particular note of steel-reinforced, metal, concrete, and other
structural materials that can inhibit radio waves.

II
Introduction
This GL240 is meant for use in Japan, the US, Europe,Taiwan,China and Korea. It has not been certied
for use under any other country’s radio laws.
The following are each region’s certication marks.
Contains NCC ID:
CCAB15LP4220T2
CMIIT ID: 2015DJ5376
MSIP-CRI-KTM-B-568
Japan
US
Europe
R 003WWA100913
Taiwan
China
Korea
Contains FCC ID: ANSBP3591
CE Mark
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
FCC CAUTION
Change or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
4. Notes for Safe Operation
(1) Be sure to use the Graphtec-supplied AC adapter. In environments where there is a lot of noise or where
the power supply is unstable, we recommend that you ground the GL240.
(2) When a high-voltage signal cable has been connected to the main unit’s analog signal input terminal,
avoid touching the leads of the input terminal’s signal cable to prevent electrical shock due to high voltage.
(3) Ensure that the GL240’s power source is positioned so that it can easily be disconnected.
(4) Do not input the voltage that is exceeding the specication of this device.
• If a voltage exceeding the specied value is input, the semiconductor relay in the input section will be
damaged. Never input a voltage exceeding the specied value even for a moment. It will cause the re.
• Have an enough margin from the specication of withstanding voltage when using this device, it have to
consider a noise and change of the measurement voltage.
• Conrm this device is not broken before the input cable is connected to the input terminal.
• Please take care of the static electricity when the connecting the input cables or the thermocouples.
• Do not touch the tip of thermocouples with bare hand after the thermocouples are connected to the
terminal of this device when the tip of thermocouples is not insulated.
The static electricity of a human body will cause damage to this device.
• Do not put the tip of thermocouples to the object which is containing the static electricity when the tip of
thermocouples is not insulated. The static electricity of object will cause damage to this device.

III
Introduction
• Do not put the tip of thermocouples to the object which is containing the leaked high voltage of chassis or
metal etc. when the tip of thermocouples is not insulated.
The leaked high voltage of object will cause damage to this device.
• We recommend that the insulation tape puts on the tip of thermocouples before connecting the
thermocouples to the input terminals.
This will protect this device from the static electricity and the leaked high voltage.
5. Notes on Functions and Performance
(1) Be sure to connect the main unit to an AC or DC power supply that conforms to the rated range.
Connection to a non-rated power supply may cause the main unit to overheat and break down.
(2) Do not block the vent on the main unit.
Continued operation with the vent blocked may cause the main unit to overheat and break down.
(3) To avoid malfunctions and other damage, avoid using the GL240 in the following locations.
• Places exposed to high temperature and/or high humidity, such as in direct sunlight or near
heatingequipment.
(Allowable temperature range: 0 to 45°C (0 to 40°C when a battery pack is mounted, 15 to 35°C when
battery is being charged), Allowable humidity range: 5 to 85%R.H., non-condensing)
• Locations subject to excessive salt spray or heavy fumes from corrosive gas or solvents.
• Excessively dusty locations.
• Locations subject to strong vibrations or shock.
• Locations subject to surge voltages and/or electromagnetic interference.
(4) If the main unit becomes soiled, wipe it off using a soft, dry cloth. Use of organic solvents (such as thinner
or benzene) causes deterioration and discoloration of the outer casing.
(5) Do not use the GL240 in the vicinity of other devices which are susceptible to electromagnetic
interference.
(6) Measured results may not conform to the stated specications if the GL240 is used in an environment
which is subject to strong electromagnetic interference.
(7) Insofar as possible, position the GL240 input signal cables away from any other cables which are likely to
be affected by electromagnetic interference.
(8) For stabilized measurement, allow the GL240 to warm up for at least 30 minutes after turning it on.
(9) When you want to use in combination of the Petit LOGGER GL100-WL (separately sold) and various
modules (such as GS sensor and terminal / adapter), please refer to the GL100 User’s Manual.
•When using in combination described above, please be careful to the operating environment because
the environmental conditions of the GL240 midi LOGGER are applied.
It may cause abnormal operation or damage.
• Allowable temperature range: 0 to 45°C, Allowable humidity range: 5 to 85%R.H, non-condensing.
(0 to 40°C when battery-powered / 15 to 35°C when charging)

IV
Introduction
Notes on the Use of This Manual
(1) All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, without the prior written permission of Graphtec Corporation.
(2) The specications and other information in this manual are subject to change without notice.
(3) While every effort has been made to supply complete and accurate information about this product, please
address any inquiries about unclear information, possible errors, or other comments to your sales representative
or nearest Graphtec vendor.
(4) Notwithstanding the preceding paragraph, Graphtec Corporation assumes no liability for damages resulting
from the use of the information contained herein or of the product.
About Registered Trademarks
Microsoft and Windows are registered trademarks or trademarks of Microsoft Corporation in the U.S. and
elsewhere.
Other company names and product names included in this manual are registered trademarks or trademarks of
their respective companies.
Copyright
All copyrights regarding this manual belong to Graphtec Corporation.

C-1
CONTENTS
CONTENTS
To Ensure Safe and Correct Use ................................................i
Safety Precautions...........................................................ii
Introduction .................................................................I
Notes on Use .................................................................I
Notes on the Use of This Manual ............................................... IV
About Registered Trademarks .................................................. IV
Copyright .................................................................. IV
CHAPTER 1 General Description
1.1 Overview.............................................................1-2
1.2 Features .............................................................1-2
1.3 Operating Environment.................................................1-3
Ambient Operating Conditions................................................. 1-3
Warming-up Before Use ..................................................... 1-3
Conguration When in Use ................................................... 1-4
1.4 Notes on Temperature Measurement .....................................1-5
1.5 Notes on Using the Monitor .............................................1-5
1.6 Changing the Display Language .........................................1-5
CHAPTER 2 Checks and Preparation
2.1 Checking the Outer Casing..............................................2-2
2.2 Checking the Accessories ..............................................2-2
Standard Accessories ....................................................... 2-2
2.3 Nomenclature and Functions ............................................2-3
2.4 Connecting the Power Cable and Turning on the Power ..................... 2-4
2.5 Connecting the Signal Input Cables ..................................... 2-6
2.6 Logic Alarm Cable Connection and Functions..............................2-7
2.7 Mounting the SD Memory Card .........................................2-10
2.8 Installing the Wireless LAN Unit (B-568: Option) ...........................2-12
2.9 Connecting to a PC ...................................................2-14
2.10 Using the Battery Pack (B-569 : Option) ..................................2-16
2.11 Connecting the Humidity Sensor (Optional)...............................2-18
2.12 Precautions to Observe When Performing Measurement....................2-19
2.13 Noise Countermeasures ...............................................2-21
2.14 Setting the Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22

C-2
CONTENTS
CHAPTER 3 Settings and Measurement
3.1 Window names and functions ...........................................3-2
3.2 Key Operation ....................................................... 3-8
3.3 Operation Modes .....................................................3-16
3.4 Setting Menus .......................................................3-19
(1) AMP settings............................................................ 3-19
(2) DATA settings ...........................................................3-43
(3) TRIG settings ...........................................................3-49
(4) Interface settings ........................................................3-55
(5) LAN setting.............................................................3-56
(6) OTHER settings.........................................................3-68
(7) FILE menu ............................................................. 3-72
(8) File box ................................................................ 3-77
(9) Text input .............................................................. 3-79
(10) Data replay menu .......................................................3-80
(11) Integrated bar graph display ...............................................3-83
(12) Quick setting ...........................................................3-87
(13) To cancel key lock by password ............................................3-88
3.5 WEB Server Function ................................................ 3-89
3.6 List of Error Codes .................................................. 3-93
CHAPTER 4 Specication
4.1 Standard Specications ................................................4-2
Standard Specications...................................................... 4-2
Memory devices............................................................ 4-3
PC I/F.................................................................... 4-3
Monitor................................................................... 4-3
Input Unit Specications ..................................................... 4-4
4.2 Function Specications ............................................... 4-5
Function Specications ...................................................... 4-5
Trigger/Alarm Functions...................................................... 4-6
External Input/Output Functions ............................................... 4-6
4.3 Accessories/Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Control Software ........................................................... 4-7
Accessories ............................................................... 4-7
Wireless Unit B-568 (Option).................................................. 4-7
Battery Pack B-569 (Option) .................................................. 4-8
Humidity Sensor B-530 (Option) ............................................... 4-8
List of Options ............................................................. 4-9
4.4 External Dimensions ..................................................4-10
INDEX ..............................................I-1

1-1
CHAPTER 1 General Description
CHAPTER 1 General Description
This chapter provides a general description of the GL240 and its features.
PRODUCT SUMMARY
1.1 Overview
1.2 Features
1.3 Operating Environment
1.4 Notes on Temperature Measurement
1.5 Notes on Using the Monitor
1.6 Changing the Display Language

1-2
CHAPTER 1 General Description
1.1 Overview
The GL240 with color monitor is a compact, lightweight data logger.
The GL240 can save the high-capacity measurement data directly in the internal memory or SD memory
card.
In addition, the setting, measuring and data capturing can be performed in online by connecting to the
computer with the USB cable.
1.2 Features
Input
• Adoption of an M3 screw type terminal facilitates wiring.
•The GL240 enables settings to be made using dedicated keys and interactive menus, using just one
hand.
Display
• With the GL240’s high-resolution 4.3-inch TFT color liquid crystal display, you can conrm the waveforms
of measured data and each channel’s settings at a glance.
•Easy operation is achieved through a straightforward menu structure and key allocation which resembles
mobile phones.
Data Capture
• The high-capacity measurement data can be saved directly in the internal memory or SD memory card.
• Because the SD memory card is used as an external memory, you can measure a long period of time with
peace of mind while data backup.
* When the optional wireless LAN unit is installed, the SD memory card cannot be inserted into the SD
CARD2 slot.
• Because disk image can be used for the internal memory, multiple data can be saved.
•The new ring memory capture function maintains latest data even after capturing for a long term. (You
need to set how long you want to keep data.)
• For voltage, temperature and humidity measurements, data can be captured at sampling rates of up to
10 ms per channel by using fewer measuring channels. (Temperature measurement can be done at
sampling rates of 100 ms and higher.)
• The GL240 is equipped with the relay recording function, and 2GByte or more data can be saved by
switching the to the other le without data missing. (When the capacity of one le reaches 2GByte, the le
is switched.)
Data Control & Processing
•The application software provided lets you set conditions and monitor data on on a computer using the
USB interface.
•The application software allows you to control multiple GL240 units from a single computer to easily
perform multi-channel measurements.
• The USB drive mode function enables the internal memory and SD memory card to be recognized as an
external drive by the PC.
(Connect the GL240 to the PC and turn on the GL240 power while holding down the [START] key.)
• Captured data can be read from the application software to les and displayed for processing.
•When optional wireless LAN unit is installed, the data capture can be performed remotely by controlling
the GL100-WL.

1-3
CHAPTER 1 General Description
1.3 Operating Environment
This section explains the operating environment for the GL240.
Ambient Operating Conditions
(1)Ambient temperature and humidity (the GL240 must be operated within the following ranges.)
• Temperature range: 0 to 45°C (0 to 40°C when a battery pack is mounted, 15 to 35°C when battery is
being charged)
• Humidity range: 5 to 85%R.H.
(2) Environment (do not use in the following locations.)
• A Location such as being exposed to direct sunlight
• Locations exposed to salty air, corrosive gases, or organic solvents
• Dusty locations
• Locations subject to vibration or impact
• Locations subject to voltage surge or electromagnetic interference such as lightning or electric furnaces
(3) Installation category (over-voltage category)
• The GL240 belongs to Installation Category II dened in IEC60664-1.
• Never use the GL240 for Installation Category III or IV.
(4) Measurement category
• The GL240 belongs to Measurement Category O dened in IEC61010-1.
• The GL240 cannot be used for Measurement Category II, III, or IV.
•If condensation occurs...
Condensation occurs in the form of water droplets on the device surfaces and interior when the GL240
is moved from a cold to a warm location. Using the GL240 with condensation will cause malfunctioning.
Wait until the condensation has disappeared before turning on the power.
Warming-up Before Use
The GL240 should be allowed to warm up with the power turned on for approximately 30 minutes to ensure
that it operates according to the specied performance.

1-4
CHAPTER 1 General Description
Conguration When in Use
Do not use the GL240 standing upright or at an angle. It must always be laid at or inclined on the stands.
<Usage Conguration>
Laid at Inclined on the stands Opening the stands
90˚
Do not block the air vent on the GL240, as this will cause malfunctioning.
Measurement accuracy may not be satisfactory if the system is used in a condition other than described
above.
To prevent possible toppling, use both of the stands of the GL240 when you place it inclined.
Use the GL240 with both of the two stands open as shown in the gure above.

1-5
CHAPTER 1 General Description
1.4 Notes on Temperature Measurement
Please observe the following precautions when performing temperature measurement.
• Do not block the air vents. Always provide a space of at least 30 cm on all sides of the GL240.
• For stabilized temperature measurement, allow the GL240 to warm up for at least 30 minutes after turning
it on.
•Exposure of the input terminals to direct drafts, direct sunlight, or abrupt changes in temperature may
impair the equilibrium of the input parts and result in measurement errors. To measure temperature in
such an environment, take appropriate countermeasures such as changing the installation site of the
GL240.
• To conduct measurement in noisy environments, connect the GL240’s GND terminal to ground (Refer to
“2.15 Noise Countermeasures”.).
• If measured values uctuate due to noise, set to a slower sampling speed (Refer to “(2) DATA setting” in “3.4
Setting Menus”.).
1.5 Notes on Using the Monitor
The monitor is an LCD display unit, and so the display will vary depending on the operating environment.
If the screen saver function is used, it will operate and clear the screen if no operations are performed
during the preset time. If the screen saver operates, press any key to restore the display.
•Condensation may form on the LCD screen if the GL240 is moved from a cold to a warm location. If this
occurs, wait until the LCD screen warms up to room temperature.
•The LCD screen is manufactured to extremely high precision. Black dots may appear, or red, blue, and
green dots may not disappear. Likewise, streaks may appear when viewed from certain angles. These
phenomena are due to the LCD screen construction, and are not signs of a fault.
1.6 Changing the Display Language
You can choose the language displayed on the screen. The default display language is set to English when
the GL240 is shipped overseas. To change the display language, see the instructions in "OTH (OTHER
menu :Language".