Great Northern Popcorn 6265 User manual

Old Fashioned
Gumball Machine
Copyright 2011 DTX International
ASSEMBLY & INSTRUCTIONS
MODEL: 6260 Gumball Machine with Stand
6265 15 Inch Gumball Machine
6270 11 Inch Gumball Machine

Copyright 2011 DTX International
Old Fashioned Gumball Machine
ASSEMBLY AND USE
Enjoying Your Old Fashioned Gumball
Machine
Your stand-alone gumball machine comes fully assembled. If
you purchased the gumball machine with stand, please visit
page 4 of this manual for instructions on stand assembly.
Your new machine is manufactured with the highest quality,
non-toxic materials available and will give you and your family
years upon years of enjoyment!
It accepts quarters, dimes, nickels and pennies (some foreign
coins too), is preset to dispense with coins, though you can
convert your machine to dispense freely (see below).
CLEANING:
You can clean all outer parts of your machine with water and a
very mild cleaner such as dish soap. DO NOT CLEAN INNER
MECHANISMS AS THIS WILL REMOVE LUBRICANTS
NECESSARY FOR OPERATION.
FILLING YOUR GLOBE:
Your machine will dispense gumballs, peanuts, hard candies,
etc....and to fill your globe, first:
1. Unscrew the cap lock (1) on the very top of the machine.
2. Next, remove the cap (2) on top of the globe (5) and fill
the globe.
3. Replace cap and lock, being careful not to overtighten.
Should you ever need to remove or replace your globe, remove
the cap lock, cap, nut (3), ring and gasket (5) and then gently
remove the globe. To reassemble, repeat in reverse order.
To collect coins, remove the baseplate (10) from the machine
body (9).
1
2
3
4
5
6
7
8
9
10

Copyright 2011 DTX International
Old Fashioned Gumball Machine
ASSEMBLY AND USE
Enjoying Your Old Fashioned Gumball Machine...Continued
HOW TO ALLOW YOUR MACHINE TO
DISPENSE FREELY:
If you do not want to require your machine to be
coin-operated, first:
1. Disassemble the machine.
2. Lay the coin mechanism on its face, coin
slot down.
3. Take out the flat black spring (11) and brass
coin dog arm (12) from the back of the coin
mechanism and set aside. Do not discard,
as you may wish to convert back to coin
operation in the future.
GENERAL PRECAUTIONS:
ALWAYS USE CAUTION WHEN REASSEMBLING MACHINE. DO NOT OVERTIGHTEN SCREWS,
ESPECIALLY NEAR GLOBE AS GLOBE MAY BE DAMAGED.
ALWAYS WATCH SMALL CHILDREN WHEN AROUND MACHINE. NEVER LEAVE UNATTENDED
AROUND SMALL CHILDREN WHO MAY BE SUSCEPTIBLE TO CHOKING.
USE CAUTION WHEN FILLING GLOBE, POUR GENTLY TO LESSEN IMPACT ON GLASS.
NEVER CLEAN WITH ABRASIVE CLEANERS. USE MILD DETERGENT AND WATER.
CONTROLLING CANDY FLOW:
You may wish to alter the rate at which your product is dispensed. To do so:
1. Remove the cap lock, cap, nut, ring and gasket and the brush-off plate (6).
2. Next, adjust the dispensing wheel. If your wheel is not able to turn, your model may have the
wheel held in place with set screws. Simply loosen them enough for the wheel to turn, adjust
and then re-tighten.
3. Reassemble. Note: when reassembling, make sure the brush-off plate covers the candy
chute.
11
12

Gumball Machine Stand Assembly
If you have purchased model 6260 Gumball
Machine with Stand you will need to do some very
minor assembly to put the stand together.
To assemble your stand:
1. First screw in the top column into the bottom
column.
2. Next, attach each leg to the base with a nut and bolt
provided as shown. Use a screwdriver, but do not
overtighten.
3. Lastly, screw the connected columns into the base.
Your stand is now fully assembled and ready to
screw in the globe on top.
For more great popcorn machines, snow cone
machines, ice shavers and concession supplies,
please visit www.greatnorthernpopcorn.com.
Copyright 2011 DTX International
Old Fashioned Gumball Machine
ASSEMBLY AND USE
Top Column
Bottom Column
Leg
Bolt
Nut
Base