Gree GJC9AG-E6RNB3A User manual

OPERATING MANUAL
ENGLISH
GJC9AG-E6RNB3A
GJC12AG-E6RNB3A
If you have lost the Owner’s Manual, please contact the local agent
or visit sat.eurofredgroup.com for electronic version.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

1
Precautions
Do not connect air conditioner to multi-purpose socket.
This appliance can be used by children aged from 8
Operation and Maintenance
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Do not spray water on indoor unit. It may cause electric
shock or malfunction.
Otherwise, it may cause fire hazard.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
years and above and persons with reduced physical,
sensory ormental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Do not wash the air conditioner with water to avoid
electric shock.
After removing the filter, do not touch fins to avoid injury.
Do not use fire or hair dryer to dry the filter to avoid
deformation or fire hazard.
Do disconnect power supply when cleaning air
conditioner. Otherwise, it may cause electric shock.
.
WARNING
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

Do not block air outlet or air inlet. It may cause
malfunction.
remote controller may be broken.
●Power cord is overheating or damaged.
●There’s abnormal sound during operation.
●Circuit break trips off frequently.
●Air conditioner gives off burning smell.
●Indoor unit is leaking.
contact the dealer or qualified professionals for service.
When turning on or turning off the unit by emergency
operation switch, please press this switch with an insulating
object other than metal.
outlet. It may cause personal injury or damage.
2
Precautions
conditioner and disconnect power immediately，and then
If the air conditioner operates under abnormal conditions,
it may cause malfunction，electric shock or fire hazard.
Do not spill water on the remote controller, otherwise the
electric shock or damage. Please contact dealer when
you need to repair air conditioner.
Do not repair air conditioner by yourself. It may cause
objects. It may cause damage or personal injury.
Do not step on top panel of outdoor unit, or put heavy
When below phenomenon occurs, please turn off air
Do not extend fingers or objects into air inlet or air
Maintenance must be performed by qualified
professionals. Otherwise, it may cause personal injury
or damage.
WARNING
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

ENGLISH
Safety operation of flammable refrigerant
Qualification requirement for installation and maintenance man
1. All the work men who are engaging in the refrigeration system should bear the
for dealing with the refrigeration system recognized by this industry. If it needs
other technician to maintain and repair the appliance, they should be supervised
2. It can only be repaired by the method suggested by the equipment’s manufac-
turer.
● Maintenance notes
1. Check whether the maintenance area or the room area meet the requirement of
the nameplate.
- It’s only allowed to be operated in the rooms that meet the requirement of the
nameplate.
2. Check whether the maintenance area is well-ventilated.
- The continuous ventilation status should be kept during the operation process.
area.
warning board should be hanged.
4. Check whether the appliance mark is in good condition.
- Replace the vague or damaged warning mark.
● Installation notes
table- Minimum room area (m2)
2. The air conditioner must be installed in a room that is larger than the minimum
room area.
The minimum room area is shown on the nameplate or following table.
3. Leak test is a must after installation.
Minimum
room
area( m 2)
Charge amount (kg) ≤1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.922.1 2.2 2.3 2.4 2.5
/ 14.5 16.8 19.3 22 24.8 27.8 31 34.3 37.8 41.5 45.4 49.4 53.6
window mounted / 5.2 6.177.9 8.9 10 11.2 12.4 13.6 15 16.3 17.8 19.3
wall mounted / 1.6 1.9 2.1 2.4 2.8 3.1 3.4 3.8 4.2 4.655.5 6
ceiling mounted / 1.1 1.3 1.4 1.6 1.8 2.1 2.3 2.6 2.8 3.1 3.4 3.7 4
Appliance filled with flammable gas R32
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

2. The refrigerant should be recycled into the specialized storage tank.
and it’s well-ventilated.
● Filling the refrigerant
fer-
ent kinds of refrigerant won’t contaminate with each other.
another time of leak detection should be done when it’s removed.
● Safety instructions for transportation and storage
container.
3. According to the local rules and laws.
●Welding
1. If you should cut or weld the refrigerant system pipes in the process of maintain-
ing, please follow the steps as below
a. Shut down the unit and cut power supply
b. eliminate the refrigerant
c. vacuuming
d. clean it with N2 gas
e. cutting or welding
f. carry back to the service spot for welding
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

1
Function
Introduction
Window type room airconditioners can regulate the room
temperature and dry the room. It is convenient for your work,study
and life. It can bewidely used in residence, shop, hotel, office, library
and laboratory, and so on.
Room
temp.
Spring
Summer
Autumn
Wind
direction
Winter
Cooling in summer
In hotsummer, Air conditioner can cooldown
theroom air by transferring heat out.
Without reducing the room temp., airconditioner
can dehumidify and make the room air dry and
comfortable.
Dehumidifying in rainy or
humid season
Exchange fresh air
Open stormdoor to keep the fresh air in the room.
Dry
Fresh Air
Heating in winter
In cold winter, air conditioner can discharge the cold
air from the room and the room will be heated.
only when your units have the HEATING function.
ENGLISH
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

If wireless remote controller is lost, open the control panel and operate manually.
Note:
2
Remote control panel
1
2
3
4 TEMP/TIMER BUTTON
℃
Select the operation mode, AUTO, HEAT, COOL, FAN,
DRY (for reverse cycle model)or AUTO,COOL,FAN, DRY
(for cooling only model).
5
6
7
This feature is areminder to clean the Air Filter (See
Care and Cleaning) for moreefficient operation and
cooling. The LED (light) will illuminate after 250 hours
"Check Filter" button and the lightwill go off.
of operation. To reset after cleaning the filter, press the
Timer / Temp
High
Mid
Low
Auto
Cool
Dry
Fan
SwingOn / Off
Fan SpeedMode
Filter
NOTTUBNOITAREPOFFO/NO
This button turns the air conditioner ON and OFF.
SWING BUTTON
Press this button to activate the supply air flap
to various position or auto swing.
FAN SPEED BUTTON
Press the button to select the Low, Middle and Hight Fan Speed.
Press the keypad to increase the set (operating)
temprature of the unit and Press the keypad to
decrease the set(operating) temperature of the unit.
The temperature seting range is from 16~30 .
Press the keypad also to increase the selected time
in 1 hour increments, and Press the keypad to
decrease the selected time in 1 hour decrements, the
time seting range is from 0~24 hours.
SIGNAL RECEIVER
FILTER BUTTON
MODE BUTTON
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

- 10 -
Buttons on remote controller
Introduction for icons on display screen
1
3
5
2
4
6
7
ON/OFF button
MODE button
+/- button
FAN button
SWING button
SLEEP button
TIMER button
Timer on Timer off
Sending signal
swing operation
sleep operation
lock
set speed
Set timeSet temperature
heat operation
fan operation
dry operation
cool operation
auto operation
Remote control operation procedure
21
3
4 5
6 7
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

- 11 -
Introduction for buttons on remote controller
Note:
● When power is connected(stand by condition), you can operate the air conditioner
through the remote controller.
●
When unit is on, each time you press the button on remote controller, the sending
signal icon " " on the display of remote controller will blink once. If the air con-
ditioner gives out a beep sound, it means the signal has been sent.
● When unit is off, set temperature will be displayed on the remote controller (If the
light of the unit display is turned on, the corresponding icon will be displayed);
When unit is on, it will display the icon of the on-going function.
Press this button to turn unit on/off.
ON/OFF button
1
Pressing this button once can select your required mode circularly as below (the
corresponding icon " " will be lit up after the mode is selected):
●
When selecting auto mode, air conditioner will operate automatically according to
ambient temperature. Set temperature can't be adjusted and won't be displayed
either. Press FAN button to adjust fan speed.
● When selecting cool mode, air conditioner will operate under cool mode. Then
press + or - button to adjust set temperature. Press FAN button to adjust fan speed.
● When selecting dry mode, air conditioner will operate at low fan speed under dry
mode. In dry mode, fan speed can't be adjusted.
● When selecting fan mode, air conditioner will operate in fan mode only. Then
press FAN button to adjust fan speed.
● When selecting heat mode, air conditioner will operate under heat mode. Then
press + or - button to adjust set temperature. Press FAN button to adjust fan speed.
(Cooling only unit can’t receive heating mode signal. If set HEAT mode by remote
controller, press ON/OFF button can’t turn on the air conditioner.)
AUTO COOL DRY FAN HEAT
MODE button
2
● Pressing + or - button once will increase or decrease set temperature by 1°F(°C).
Hold + or - button for 2s, set temperature on remote controller will change quickly.
Release the button after your required set temperature is reached.
● When setting Timer On or Timer Off , press + or - button to adjust the time.(See
TIMER Button for setting details)
+ / - button
3
● This is a general use remote controller, it could be used for the air conditioners
with multifunction; For some function, which the model doesn't have, if press
the corresponding button on the remote controller that the unit will keep the
original running status.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

- 12 -
Introduction for buttons on remote controller
Press this button to turn on left & right air swing.
SWING button
5
Under Cool, Heat mode, press this button to turn on Sleep function. Press this button
to cancel Sleep function. Under Fan, Dry and Auto mode, this function is unavailable.
SLEEP button
6
TIMER button
7
Note:
● Under Auto speed, air conditioner will select proper fan speed automatically acc-
ording to ambient temperature.
● Fan speed can't be adjusted under Dry mode.
FAN button
4
Pressing this button can select fan speed circularly as: AUTO, SPEED 1 ( ),
SPEED 2 ( ) , SPEED 3 ( ), SPEED 4 ( ) (unavailable in this air conditioner.
Speed 4 is the same with speed 3.).
AUTO
SPEED 1 (equals to low fan speed)
SPEED 3 (equals to high fan speed) SPEED 4 (equals to high fan speed)
SPEED 2 (equals to mid fan speed)
● When unit is on, press this button to set Timer Off. T-OFF and H icon will be
blinking. Within 5s, press + or - button to adjust the time for Timer Off. Pressing
+ or - button once will increase or decrease the time by 0.5h. Hold + or - button
for 2s, time will change quickly. Release the button after your required set time
is reached. Then press TIMER button to confirm it. T-OFF and H icon will stop
blinking.
●When unit is off, press this button to set Timer On. T-ON and H icon will be
blinking. Within 5s, press + or - button to adjust the time for Timer On. Pressing
+ or - button once will increase or decrease the time by 0.5h. Hold + or - button
for 2s, time will change quickly. Release the button after your required set time
is reached. Then press TIMER button to confirm it. T-ON and H icon will stop
blinking.
●Cancel Timer On/Off: If Timer function isset up, press TIMER button once to
review the remaining time. Within 5s, press TIMER button again to cancel this
function.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

3
Operating Condition
COOL mode operation
Outdoor temperatureshould be in rangeof 18
to 43 , otherwise it ispossible for airconditioner
to breakdown.
Room humidity should be lower than 90% .
Otherwise, it ispossible for airconditionerto dew
at air conditioner surface and even drop water after
running for so much time. But this maybe normal.
Please operate air conditioner in the correct conditions as following.
Power requirement
Water pipe
The electric components will bedamaged when the voltage is too high.
If the voltage istoo low, the compressor will vibrate violently to dam-
age the refrigerant system and easily cause the compressor and elec-
tric components notwork.
Special socket mustbeused. Furthermore, the socket and wiring
must conform to the wiring regulations. And the earthing method
mustbereliable.
In fixed circuit, there must be electricity leakage protection switch
of enough power capacity and air switch with enough space.
Earth wire To ensure the reliable earthing, please do not connect earth wire to the following places:
The ground must be connected.
ENGLISH
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

4
Installation
Installation precaution:
Windowtype conditioneris so valuable and the improperinstalla-
tion of it will cause a lot of damage! Please associate the profes-
sional technician to install the unit and don’t install it by yourself.
Otherwise, we are not responsible for the damage like this.
Location:
The condensation water mustbe drained away conveniently.
Install air conditioner unit far away from TV set or radio
etc. to avoid disturbing video or voice.
In salt and coastal area or place where is near thermal springs
and polluted by sulphurousgas, orother special areas, please
contact the seller before use.
Avoid a place where ispossible for inflammable gasto leak out.
Avoid other heat sources or direct sun light.
Avoid a place where is easy for children to touch.
For window type air conditioner with remote
control, install in a location where is strong elec-
tromagnetic disturbance, you should contact the
seller in advance to avoid the malfunction in use.
How to install:
Choose a location where there are no any obstacle surrounding
the unit.
Prepare the installation hole slightly bigger than unit size.
Choose the installation space according to the following diagram.
Cooling
375 560
660 428
9K
12K
The minimum clearance from the appliance to combustible
surface is 50 mm.
The distance of obstructions from window unit inside should
be upper 300mm, lower 1500mm, left 500mm, right 500mm,
front 1500mm.
capability
A B
Over
1000 mm
A
B
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

ENGLISH
5
Horizontal line
Sunshade board
Wall
Wooden frame
Rubber plate
Support
Horizontal line
Drain water:
To get the maximum cooling efficiency, the airconditionerisdesigned to splash the condensation wateron the
condenser coil.
If the splashing sound annoys you, you can provide an outside drain by using the following procedure, which
may however causeasmall loss of performance.
1. Slide out the chassis from the cabinet.
2. Remove the rubber plug from the body base plate.
3. Install the drain pan to the corner of the cabinet with 2 screws.
4. Connect the drain hose to the outlet on the drain pan bottom.
5. Slide the chassis into its original place in the cabinet.
Installation procedure:
1) Remove the sticker from the frontpanel.
2) Put the unit into the installation hole.
When installing the unit, it should beslanted
down to the back to avoid the enlar gement of
noise orvibration. (Slant between 6-10mm. )
(Shown at rightfigure.)
The installation place should bestrong enough
to avoid the enlargement of noise or vibration.
3) Fill up sews in the cabinet with spongeor foam.
Installation assistance:
Use iron support
The installation hole should bestrong enough to
support the airconditioner. If it cannot, iron sup-
port has to be used outdoors.
Iron supportshould befixed on the building (Shown
at right figure.)
Usesunshade board
Air conditioner should avoid anything to be dropped
into it and avoid direct sunshine. If there is no cover
on it, you should contact the seller for installing
the sunshade board. When installing the sunshade
board, don’t let it block the air inlet at the side grille.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

6
Notes for installation
Remove
Before removing airconditionerto the otherplace, you should
contact the seller firstly.
Then it mustbedoneunder the direction of the professional
technician. In addition, the charge of this must be paid.
Noise
Electric wiring
Install in a location where is firm enough to avoid the enlargement of noise
and vibration.
Don’t put anything in front of the outlet of outdoor unit to avoid increasing
noise.
Be sure that hot air o r noise will not inconvenience neighbors.
Please contactthe seller as soon as there is strangenoise during operation.
Please use the safety support.
Must connect with ground reliably.
The exclusive circuit mustbeused. But removable socket can’ t beused because poor
contact of it can cause over heat or fire.
Don’t pull the power cord strongly.
In fixed circuit, there must be electricity leakage protection switch and leakage current
is less than 30mA.
Air switch (thermal-magnetic breaker) should be installed in the circuit and its capacity
is 10A .
The cross section area for fixed wiring should be more than 1.5mm
2
.
Note:
Drain hoseor tubing can bepurchased locally to satisfyyour particular needs.
If the supply cord is damaged, It must be replaced by the manufacturer or its service agent or similarly
qualified person in order to avoid a hazard .
The appliance must be positioned so that the plug is accessible.
The appliance should be installed in accordance with national wiring regulations.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

ENGLISH
Vertical airflow direction vane
(Airflow direction adjustment up and down).
The vertical airflow direction vane is controlled by
positioning the vane to discharge the air upwards,
downwards or straight out.
Air direction adjustment
PART IDENTIFICATION
Air filter
(behind the front intake grille)
Front intake grille
Control panel cover
Front grille
Air inlet louver
Cabinet
7
Panel outlook picture, just for reference, please take the real unit as standard.
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

Operation Tips
Operation for comfort and economy
Do not overcool the room
temperature . This is notgood
for health and wastes electricity.
Keep blind or curtains closed.
Do not let sunshine enter the
roomdirectly when the air con-
dition is in operation.
Keep the room temp. uniform.
Adjust the vertical and horizon-
tal airflowdirection to ensure a
uniform temperature in the room.
Air can’t bedischarged to the di-
rection of air-in.
Make sure that the doors and win-
dows are tightly closed.Avoid open-
ing doors and windows asmuch as
possible to keep air conditioning in the
room.
Clean the air filter regularly.
Blockages in the air filter re-
duce dehumidifying effects.
Clean the air filterat least once
every two weeks.
Ventilate the room occasionally.
Since windows are kept closed, it
is a good idea to open them and
ventilate the room now and then.
When starting the unit, curtains or
windows should be closed to pre-
vent the heat/cool leakage.
8
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

ENGLISH
Caution
Do notuse the air conditioner
for other purposes except for
cooling the room.
Do notuse the air conditioner
for otherpurposes such as
drying clothes, preserving
foods, or cultivating
vegetables.
Do notblock the air intake and
outlet vents
This causes lowered perfor-
mance and irregular operation.
Do not insert sticks or other
objectsinto these ventsasit is
dangerous to touch the electric
components and the fan.
Select the most appropriate
temperature.
Pay attention to adjust the tempera-
ture to suit the conditions.
Rooms occupied by infants,the
elderly, orthe sick should be kept at
an appropriate temperature.
Do not use heating apparatuses in
the vicinity.The air conditioner s
plastic parts will melt if exposed to
excessive heat.
Avoid exposing the body directly to
a continuous unidirectional air flow
for long periods.
Thisisnot recommended for health
reason.
Always wait at least 3 minutes beforeswitching the
airconditioneron again afteryou have switched it
off during cooling . The appliance should not be used
by children without supervision.
Always wait
at least 3 minutes
Do not pull out the power cord.
Damage to the cord may result
in serious electric shocks.
9
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

Care and maintenance
Always turn off the air conditioner and main power supply before cleaning to ensure safety.
Cleaning unit
1. Cut power off before cleaning.
3. Don’t use gas, benzene, solvent,wash, chemical
solvent, etc. for cleaning.
4. Do not splash waterdirectly into indoor
* Check earth wire
Vacuum cleaner
Plug outonly after
air conditioner
stops at all.
Dry the cloth by
hands befor e
cleaning.
unit, in which
there are micro-
computerand
circuit plate,
they must not be
drenched with
water.
Accident could
happen.
Is it broken
or loose?
Air lock could result
in bad efficiency.
*Check if air inlet and outlet of outdoor unit
are blocked or not.
Let the filter dry thoroughly before reinstalling it.
If. necessary, please ask the professional personnel to
clean it.
2. Vacuum the filter on the dusty side to remove light dust.
3. Wash the filter, cleaner side up undergently flowing water
to wash out accumulateddust and lint.
4. If the filterisvery dirty, use a mild household detergent in
the wash water.
2. Usesoft dry cloth when
cleaning cabinet.
If the cabinet isvery
dirty, dip cloth into warm
waterbelow40
Air filter
The air filter behind the intake grille should bewashed at least
once every two weeks or as often as it needs cleaning.
How to clean the air filter:
1. To remove the air intake grille, grasp the tab on the filter and
pull to take out.
dry
the cloth and then rub off
the dirt.
10
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.

ENGLISH
Trouble shooting guide
Fault phenomenon Trouble-shooting
Air conditioner does not
operate at all.
* Is there a power failure?
* Is the plug out?
* Is power fuse or switch off ?
* Is air inlet or outlet locking?
* Is there any other heat source in room?
* Are air filters dirty very much?
* Is indoor fan speed set at LOW?
*Maybe the room is too hot when the unit is started,
please cool down the room after a period of time.
*At COOL mode operation, sometimes there is foggy
air flowing out of indoor unit, this is because the room
humid air has been cooling rapidly.
*The unit is normal while the indoor outlet is sending
out some odor, because the inlet air may be mixed
with the smell of furniture and smoke.
*For a noise that sounds like water flowing:
This is the sound of freon flowing inside the air con-
ditioner unit.
* For a noise that sounds like a shower:
This is the sound of the dehumidifying water being
processed inside the air conditioner unit.
*Condensation occurs when the airflow from the air
conditioner cools the warm room air.
* This is to protect the mechanism.
* Wait about three minutes and operation will begin.
Cool ef ficiency is not
good.
Fo ggy air
flows out.
The air conditioner opera-
tion is noisy.
It seems that condensation is leaking from air conditioner.
Air conditioner do ess not operate for about 3 minutes when
restart.
Please check the following items before asking for repair,it saves your time and
money.
11
Copyright 2018. This translation is property of GREE PRODUCTS SL. All rights reserved. Total or partial reproduction without its express authorization is prohibited.