Green Brook DW040A User manual

MODEL NUMBERS:
DW040A: Ambassador wirefree kit
DW040AG: Ambassador wirefree kit
DW040AS: Ambassador wirefree kit
DW041A: Ambassador receiver only
DW050A: Beacon Wirefree Kit
DW051A: Beacon wirefree receiver
• No more wires
• Simply insert batteries
• Batteries included for Transmitter
(2 x AAA)
• Receiver requires three Alkaline
”C cell“ LR14 batteries
• Transmitter screws included
Please read the instructions fully
before attempting installation.
1a) TRANSMITTER
The battery compartment slot is
located on the bottom of the unit.
Using a flat screw driver insert into slot
and gently push to remove the lower
cover. Insert the two AAA batteries
supplied and refit the base cover.
1 b) RECEIVER
The battery compartment is located
on the base.
Remove cover gently by pushing and
releasing the two tabs.
Insert three batteries, ensuring the
correct polarity so that the negative
end is always resting on the spring
and the positive end on the flat metal
plate.
The first battery goes in the lower
compartment with the negative end
against the spring.
The other two are inserted as shown
in diagram 4. above.
Replace battery cover carefully.
Press the button on the transmitter
Diag. 1.
Transmitter Diagram 2. Receiver
Diagram 4.
Receiver
(cross section)
Skip to section 5 unless you wish
to change the factory set tune,
volume or house codes.
WIREFREE DOORCHIMES
Diagram 3.
STEP 1. TESTING THE
TRANSMITTER AND
RECEIVER WITH BATTERIES
STEP 3. TUNE SELECTION &
VOLUME CONTROL
(FLASHING LIGHT ONLY AVAILABLE
ON MODELS DW050A AND DW051A)
STEP 2. INSTALLING
THE TRANSMITTER TO
THE DOOR
and the doorchime will sound.
You have now tested your doorchime.
If there is no sound, check that
batteries are inserted correctly and
that they are not exhausted.
Before drilling any holes position the
transmitter on the door or door frame
outside (ideally a flat wooden area)
and press the button to ensure the
signals are getting through to the
receiver. Please test with the door
closed to simulate actual working
conditions. You should also look to
position the transmitter in an
unexposed place to protect from rain.
The range of the unit is up to 100
metres but mounting the transmitter
on metal or UPVC doorframes may
make the unit inoperative or seriously
reduce the operating range.
As with all low powered transmitters
the number of walls and ceilings the
signal has to travel through, between
the transmitter and receiver also
affects the range.
Once a suitable surface is found
remove the transmitter base follow-
ing 1a).Use this as a template to fix
the base on to a doorframe. Ensure
the transmitter is the right way up so
that the slot is at the bottom.
If mounting on to masonry, wall fixings
will be required. Refit unit to the base.
IMPORTANT : The screws must be
fixed flush or the battery will not
maintain contact with the terminals
and the unit will not operate.
TUNE SELECTION
The unit comes with a factory pre-set
tune but it can be changed.
The tune is determined by the slider
switch as in Diagram 3.
Remove transmitter cover as in 1a)
above leaving the battery in and
select tune as shown in Diagram 3.
Press the push button to hear the
sound each different setting produces.
Once a desired tune is selected,
Carefully replace transmitter. Up to 3
different sound options are available.

STEP 4.
CHANGING HOUSE CODE
STEP 5. TESTING
6. TROUBLE SHOOTING
7. CONNECTING TO AN
EXISTING SYSTEM
GUARANTEE
REMARKS
VOLUME CONTROL
4 levels of volume can be set, see
Diagram 5. Repeatedly pushing the
volume switch will cycle through the 4
levels of volumes available.
FLASHING LIGHT (DW050A & DW051A)
A bright xenon light will flash and
accompany the tune. This feature is
particularly useful for the hard of
hearing or when using the chime in a
noisy environment. The volume can
be muted following the instructions
above.
If you have the model DW040A
Ambassador Kit but would like the
flashing light feature, you can
purchase the GreenBrook model
‘DW051A Beacon Receiver’ seperately.
This can be used on it’s own or as an
additional receiver.
See Diagram 5. for the sound/flashing
light options.
The unit comes with factory set code.
Only change it if you experience
interference from a neighbour’s unit.
Remove cover transmitter from base
as in 1a) leaving the batteries in
position. Set the dial as in Diag.3. to
required number i.e “6”, set this
number “6” on the corresponding dial
on the reciever.
Press push button on the transmitter
to check that the chime works and
carefully replace transmitter as above.
Test your doorchime by moving the
receiver in different rooms and at
varying distances from the
transmitter to ascertain the coverage
available in your home, this way you
are unlikely to miss any visitors. If
preferred, the receiver can be hung
on a wall using the keyhole slot at
the back.
Fault : Chime does not sound
Cause :
• Check batteries are not flat and
they have been inserted the correct
way round. Do not mix different
types of batteries.
• Re-check the dials and switches in
the transmitter and reciever if the
house codes have been amended.
• Move the receiver nearer the
transmitter.
• Re-check the volume control
If after going through the trouble
shooting section, you still experience
difficulty please ring us on
GreenBrook‘s Help Line
01279 772 750
during office hours quoting
the model number
Using additional wirefree transmitters
or Receivers.
To identify visitors at a second door,
a DW060A transmitter can be
purchased separately and fixed to the
outside door. Follow instructions in
section 2 above. A different tune on
the second transmitter can be selected
to identify which door the caller is at.
Follow section 3 above. Ensure the
house codes on all the transmitters
and receivers are identical (see section
4 above).
Additional receivers are also available
– models DW041A and DW051A, so
that doorchime can be heard in a
different part of the house simultane-
ously e.g. in the garden shed and in
the kitchen.
Your door chime is guaranteed for 12
months from date of purchase. Please
retain till receipt as proof of purchase.
This is in addition to your statutory
rights.
For indoor use only.
No naked flame sources, such as
lighted candles should be placed
near the unit.
The unit should not be exposed to
dripping or splashing and no
objects filled with fluids. such as
being placed near vases.
Please dispose of old, defective
batteries in an environmentally
friendly manner in accordance
with the relevant legislation.
This symbol indicates seperate
collection of electronic/electrical
equipment.
PLEASE KEEP THESE
INSTRUCTIONS SAFE
FOR FUTURE REFERENCE
House
Codes
Volume
Diagram 5.
Issue Number: 701325
West Road,
Harlow,
Essex
CM20 2BG
Tel [phone]
Fax [phone]
Email: [email protected]
Web: www.greenbrook.co.uk
1. “Flash Doorbell”
2. “Doorbell”
3. “Flash”