Green Brook Orion Range OD103 User manual

‘Orion Range’
Infra-red Motion Detector - IP65
Model: OD103 & OD103B
Important Safety Instructions
• Please read these instructions carefully before installation and keep safe for future
reference.
IMPORTANT
This product should be installed by a competent person and in accordance with the
current IET Wiring Regulations and Building Regulations.
If in doubt,consult a qualified electrician.
• Always turn off the mains supply before commencing work.
Switch the mains supply OFF first to prevent electric shock.
1. Remove the rear cover by removing the
screw and pulling off cover, refer to Dia:1.
2. Connect the mains in and load out
cable according to Dia: 2 feeding
cable through the silicon grommet.
Dia:1 Dia:2
Detection from Above
Poor Sensitivity
Good Sensitivity
As the detector responds to changes in temperature, avoid the following situations:-
• Avoid pointing the detector towards objects with highly reflective surfaces, such as
mirrors etc.
• Avoid mounting the detector near heat sources, such as heating vents, air conditioning
units, lights etc.
• Avoid pointing the detector towards objects that may move in the wind, such as
curtains, tall plants etc.
INSTALLATION
This product uses an infra-red heat detector. The detector senses ‘warmth movement’ in the
surrounding area when it is dark. When movement is detected the sensor is activated and
triggers the connected load. It has a built in photo-cell that can identify day and night.
FIELD OF DETECTION
OD103
OD103B
Note: Please refer to Data Sheet on the GreenBrook website -
www.greenbrook.co.uk for wiring sensor in parallel.
OD103 B Ins Aug 21_Layout 1 21/02/2022 16:48 Page 1

4. Position sensor onto back plate and secure using the screw removed in step 1.
1. Turn ‘Time’ control fully anti-clockwise
and ‘Lux’ control fully clock wise refer
to Dia: 4.
2. Re-connect mains supply, allow 30
seconds for the sensor to warm-up,
and then perform a walk-by in front of
the sensor; lamp should turn on and
stay on for approximately 10 seconds,
and will go off if no further movement
is detected.
TESTING
ADJUSTING THE ‘LUX’ CONTROL
1. Turning Lux control fully clock wise, the sensor will operate in both daylight and
darkness.
2. Turning Lux control fully anti-clockwise, the sensor will operate in darkness only.
3. Set control to operate at your required daylight level.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning the time control fully anti-clock wise will set the on duration to 10 seconds
+/- 3 seconds.
2. Turning the time control fully clock wise will set the on duration to 15 minutes +/-
2 minutes.
TROUBLE SHOOTING
Li ht not comin on
• Check that lamp is good.
• Check there is nothing obscuring the PIR sensor.
Intermittent operation
• Check there are no curtains that can move in the wind.
• Check there are no heating vents nearby.
TECHNICAL INFORMATION
Rated Voltage: 230V~50Hz
IP Rating: IP65
Ambient Light: <3-2,000 LUX (Adj)
Time Delay: Min 10 sec ± 3 sec
Max 15 min ± 2 min
Rated Load: Max 1200W
Max 300W
Detection Range: 180°
Detection Distance: 12M max (<24°C)
Working Temp: -20° - + 40°C
Working Humidity: <93%RH
Power Consumption: 0.5W approx
Installation Height: 1.8 - 2.5M
Detection Moving Speed: 0.6 - 1.5m/s
Dimensions: 119.5 x 80 x 51.5mm
Conforms To: BS E 61058-1
Dia:4
Dia:3
3. Secure the sensor back plate to the wall
using two wood screws (ensure there is no
wiring/gas/water services directly behind
the screws) Dia:3.
/LED
Issue no: 706821
EST ROAD . HARLO
ESSEX . CM20 2BG . UK
[e-mail]
www.greenbrook.co.uk
GUARANTEE
Your GreenBrook Motion Detector IP65
OD103/B is uaranteed for 1 year
from the date of purchase.
This is in addition to your statutory ri hts.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
NOTE:
Product & Packaging Disposal
When disposin of this item and its packa in please follow local
re ulations and use an appropriate waste disposal centre.
See GreenBrook website for further details.
OD103 B Ins Aug 21_Layout 1 21/02/2022 16:48 Page 2