Green Brook Orion Range OD102 User manual

‘Orion R nge’
Infr -red Motion Detector - Ceiling Mounted
Model: OD102
Import nt S fety Instructions
• Please read these instructions carefully before installation and keep safe for
future reference.
IMPORTANT
This product should be installed by a competent person and in accordance
with the current IET Wiring Regulations and Building Regulations.
If in doubt,consult a qualified electrician.
• Always turn off the mains supply before commencing work.
Di :1
1. Remove the cover by rotating anti-clock wise.
2. Connect the mains in and load out wires according to Dia:1.
Sw tch the ma ns supply OFF f rst to prevent electr c shock.
N = Neutr l ‘IN’
L = Live ‘IN’
A = Output to Lo d
This product uses an infra-red heat detector. The detector senses ‘warmth movement’ in the
surrounding area when it is dark. When movement is detected the sensor is activated and
triggers the connected load. It has a built in photo-cell that can identify day and night.
Poor Sens t v ty
FIELD OF DETECTION
Good Sens t v ty Detect on from
Above
As the detector responds to changes in temperature, avoid the following
situations:-
• Avoid pointing the detector towards objects with highly reflective surfaces,
such as mirrors etc.
• Avoid mounting the detector near heat sources, such as heating vents, air
conditioning units, lights etc.
• Avoid pointing the detector towards objects that may move in the wind,
such as curtains, tall plants etc.
I STALLATIO
Note: Ple se refer to D t Sheet on the GreenBrook website -
www.greenbrook.co.uk for wiring sensor in p r llel.
OD102 Ins Aug 21_GU10 21/02/2022 16:42 Page 1

Di :3
TESTING
ADJUSTING THE ‘LUX’ CONTROL
1. Turning Lux control fully clock wise, the sensor will operate in both daylight and
darkness.
2. Turning Lux control fully anti-clockwise, the sensor will operate in darkness only.
3. Set control to operate at your required daylight level.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning the time control fully anti-clock wise will set the on duration to 10 seconds
+/- 3 seconds.
2. Turning the time control fully clock wise will set the on duration to 15 minutes +/- 2
minutes.
Replace cover by positioning cover and rotating clockwise.
TROUBLE SHOOTING
L ght not com ng on
• Check that lamp is good.
• Check there is nothing obscuring the PIR sensor.
Interm ttent operat on
• Check there are no curtains that can move in the wind.
• Check there are no heating vents nearby.
TECHNICAL INFORMATION
Rated Voltage: 230V~50Hz
IP Rating: IP20
Ambient Light: <3-2,000 LUX (Adj)
Time Delay: Min 10 sec ± 3 sec
Max 15 min ± 2 min
Rated Load: Max 1200W
Max 300W
Detection Range: 360°
Detection Distance: 6M max (<24°C)
Working Temp: -20° - + 40°C
Working Humidity: <93%RH
Power Consumption: 0.5W approx
Installation Height: 2.2 - 4M
Detection Moving Speed: 0.6 - 1.5m/s
Dimensions: 80Ømm
Depth - 41mm
Conforms To: BS E 61058-1
Di :2
1. Turn ‘Time’ control fully anti-
clockwise and ‘Lux’ control fully
clock wise, refer to Dia: 3.
2. Re-connect mains supply, allow 30 seconds for the sensor to warm-up, and
then perform a walk-by in front of the sensor; lamp should turn on and stay on
for approximately 10 seconds, and will go off if no further movement is
detected.
/LED
3. Secure the sensor back plate to the wall using
two wood screws (ensure there is no
wiring/gas/water services directly behind the
screws) Dia:2.
Issue no: 706820
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
[e-mail]
www.greenbrook.co.uk
GUARANTEE
Your GreenBrook Mot on Detector Ce l ng
Mounted OD102 s guaranteed for 1 year
from the date of purchase.
Th s s n add t on to your statutory r ghts.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
NOTE:
Product & P ck ging Dispos l
When d spos ng of th s tem and ts packag ng
please follow local regulat ons and use an
appropr ate waste d sposal centre.
See GreenBrook webs te for further deta ls.
OD102 Ins Aug 21_GU10 21/02/2022 16:42 Page 2