Green Brook Orion ODM202 User manual

‘Orion Range’
Infra-red Microwave Presence Detector
- Programmed Settings
Model: ODM202
Switch the ains supply OFF first to prevent electric shock.
INSTALLATION
Our range of PIR microwave presence detectors are designed to reduce the amount of time
lighting is left on unnecessarily, for example if an area is unoccupied or if there is sufficient
natural light.
A presence detector monitors the detection zone for occupancy, using radio waves in the
microwave band (5.8 GHz) if a person is sensed then the detector will automatically turn the
lighting on. When the area is vacated, the lighting will turn off after a preset time delay. Most
of our microwave sensors have a built in light level (lux) sensor which will keep the lighting off if
there is enough natural light available.
Controlling lighting with a presence detector can save up to 60% of lighting energy costs
dependent on occupancy behaviour and the amount of natural light available; our
microwave sensors can also be used to control heating and ventilation.
As this detector uses microwaves, detection is possible through plastic, glass and thin walls
such as office partitions. It will not detect movement through brick, concrete or metal.
With ambient light
more than the setting
value, the lamp does
not switch on when
someone enters the
room.
With ambient light less
than daylight threshold,
the lamp will be on
100% when someone
enters the room.
After the hold time, the
light switches off
automatically when no
movement is detected.
1. Decide on mounting position of sensor in and screw into position using the two mounting
lugs at either end. (ensure there is no wiring/gas/water services directly behind the screws)
refer to Dia:1.
Dia:1
2. Connect the mains in and load out wires according to Dia:1 and Dia:2.
I portant Safety Instructions
• Please read these instructions carefully before installation and keep safe for future
reference.
IMPORTANT
This product should be installed by a competent person and in accordance with the
current IET Wiring Regulations and Building Regulations.
If in doubt,consult a qualified electrician.
• Always turn off the mains supply before commencing work.
ODM202 Ins Mar.qxp_GU10 07/04/2017 14:51 Page 1

1. Time control can be adjusted between 5 seconds and
30 minutes, using a combination of slide switches, see
Table 2.
2. Set control to operate at your required time period.
ADJUSTING THE ‘LU ’ CONTROL
Dia:2
Control Gear
or Lamp
Control Gear
or Lamp
Control Gear
or Lamp
TESTING
1. Slide all 9 slide switches to the ‘Up’ position .
2. Re-connect mains supply, allow 30 seconds for the sensor to warm-up, and then perform
a walk-by in front of the sensor; lamp should turn on and stay on for approximately 5
seconds, and will go off if no further movement is detected.
Table:1
1. ux levels can be set between 2000 ux (daylight) and 2
ux (night), using a combination of slide switches, see
Table 1.
2. Set control to operate at your required daylight level.
Table:3
1. Sensitivity can be adjusted between a detection
cone of 1 meter (10%) and a detection cone of 8
meters (100%) using a combination of slide switches,
see Table 3.
2. Set control to operate at your required time period.
TROUBLE SHOOTING
Light not co ing on
• Check that lamp is good.
• Check there is nothing obscuring the microwave sensor.
Inter ittent operation
• Check there are no curtains that can move in the wind.
• Check there are no heating vents nearby.
TECHNICAL INFORMATION
/ ED
Table:2
ADJUSTING THE ‘SENSITIVITY’ (DETECTION AREA) CONTROL
Issue no: 704791
WEST ROAD . HARLOW
ESSE . CM20 2BG . UK
[e-mail]
www.greenbrook.co.uk
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
GUARANTEE
Your GreenBrook Microwave Presence Detector
ODM202 is guaranteed for 1 year
fro the date of purchase.
This is in addition to your statutory rights.
ADJUSTING THE ‘TIME ON’ CONTROL
Rated Voltage: 230V～50Hz
IP Rating: IP20
Ambient ight: 2 UX, 5 UX, 20 UX,
50 UX, 2000 UX (choice)
Transmission Power: <0.2mW
HF System: 5.8GHz CW radar, ISM band
Hold Time: 5s, 30s, 1min, 5min, 10min,
20min, 30min (choice)
Rated oad: Max 1200W
Max 300W
Detection Range: 360° /180°
Detection Area: 10%,30%,50%,75%,
100% (choice)
Detection Distance: Wall = 5 - 15M adj
Ceiling = 1 - 8M (radius) adj
Power Consumption: 0.9W approx
Installation Height: Wall = 1.5 - 3.5M
Ceiling = 2 - 8M
Detection Moving Speed: 0.6 - 1.5m/s
Dimensions: 63.5 x 37 x 25mm
ODM202 Ins Mar.qxp_GU10 07/04/2017 14:51 Page 2