Green Brook Orion ODM200 User manual

‘Orion Range’
Microwave Presence Detector - Ceiling Mounted
Model: ODM200
Important Safety Instructions
• Please read these instructions carefully before installation and keep safe for future
reference.
IMPORTANT
This product should be installed by a competent person and in accordance with the
current IET Wiring Regulations and Building Regulations.
If in doubt,consult a qualified electrician.
•Always turn off the mains supply before commencing work.
Dia:1
1. Remove the transparent terminal cover by removing the small cross head screw and
levering off cover.
2. Decide on mounting position of sensor in ceiling, and cut a 65mm hole, (ensure there
is no wiring/gas/water services directly behind the screws).
3. Connect the mains in and load out wires according to Dia:1.
Switch the mains supply OFF first to prevent electric shock.
INSTALLATION
Our range of PIR microwave presence detectors are designed to reduce the amount of
time lighting is left on unnecessarily, for example if an area is unoccupied or if there is
sufficient natural light.
A presence detector monitors the detection zone for occupancy, using radio waves in the
microwave band (5.8 GHz) if a person is sensed then the detector will automatically turn
the lighting on. When the area is vacated, the lighting will turn off after a preset time delay.
Most of our microwave sensors have a built in light level (lux) sensor which will keep the
lighting off if there is enough natural light available.
Controlling lighting with a presence detector can save up to 60% of lighting energy costs
dependent on occupancy behaviour and the amount of natural light available; our
microwave sensors can also be used to control heating and ventilation.
As this detector uses microwaves, detection is possible through plastic, glass and thin walls,
such as office partitions. It will not detect movement through brick, concrete or metal.
To
Load Live in
Neutral
TESTING
Dia:2
1. Turn ‘Time’ control fully anti-clockwise, ‘Lux’ control fully clock wise and ‘Sens’ control
fully clockwise refer to Dia:2.
Note: Please refer to Data Sheet on the GreenBrook we site -
www.green rook.co.uk for wiring sensor in parallel.
ODM200 Ins Jan 22_GU10 21/02/2022 12:55 Page 1

Dia:3
1. Turning Lux control fully clock wise, the sensor will operate in both daylight and darkness.
2. Turning Lux control fully anti-clockwise, the sensor will operate in darkness only.
3. Set control to operate at your required daylight level.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning the time control fully anti-clock wise will set the on duration to 10 seconds +/- 3
seconds.
2. Turning the time control fully clock wise will set the on duration to 12 minutes +/- 2
minutes.
AD USTING THE ‘SENSITIVITY’ CONTROL
1. Turning the sens control fully anti-clock wise will set the sensitivity to minimum (approx.
1M detection cone).
2. Turning the sens control fully clock wise will set the sensitivity to maximum (approx. 8M
detection cone).
Replace the clear cover removed above. Fold the metal springs of the sensor upwards and
insert into the installation hole releasing springs, the springs will hold sensor in position, refer
to Dia:3.
TROUBLE SHOOTING
Light not coming on
• Check that lamp is good.
• Check there is nothing obscuring the microwave sensor.
Intermittent operation
• Chec there are no curtains that can move in the wind.
• Chec there are no heating vents nearby.
2. Re-connect mains supply, allow 30 seconds for the sensor to warm-up, and then perform
a walk-by in front of the sensor; lamp should turn on and stay on for approximately 10
seconds, and will go off if no further movement is detected.
ADJUSTING THE ‘LUX’ CONTROL
Step 1
Step 2
Step 3
TECHNICAL INFORMATION
/LED
Issue no: 706824
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
[e-mail]
www.green rook.co.uk
GUARANTEE
Your GreenBroo Microwave Presence Detector
ODM200 is guaranteed for 1 year
from the date of purchase.
This is in addition to your statutory rights.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
NOTE:
Product & Packaging Disposal
When disposing of this item and its pac aging
please follow local regulations and use an
appropriate waste disposal centre.
See GreenBroo website for further details.
Rated Voltage: 230V~50Hz
IP Rating: IP20
Ambient Light: <3-2,000 LUX (Adj)
Time Delay: Min 10 sec ± 3 sec
Max 12 min ± 1 min
Rated Load: Max 1200W
Max 300W
Detection Range: 360°
Detection Distance: 1-8M adjustable
HF System: 5.8GHz CW radar, ISM band
Transmission Power: <0.2mW
Power Consumption: 0.9W approx
Installation Height: 1.5 - 3.5M
Cut Out: 65mm
Detection Moving Speed: 0.6 - 1.5m/s
Dimensions: 76Ømm
Total Depth - 75.4mm
Ceiling Protrusion - 17.2mm
Conforms To: BS EN61058-1
ODM200 Ins Jan 22_GU10 21/02/2022 12:55 Page 2