Greenlee Pull Connect User manual

INSTRUCTION MANUAL
Pull Connect
Read and understand all of the instructions and safety
information in this manual before operating or servicing
this tool.
KEEP THIS MANUAL
Record serial number here
_______________________
52094539 REV 03 © 2024 Greenlee Tools, Inc. ECN002542/03 1/24
Español ..............20-37
Français .............38-56

Pull Connect
52094539 REV 032© 2024 Greenlee Tools, Inc.
KEEP THIS MANUAL
Table of Contents
Safety Symbols Key ....................................................... 3
Safety Warnings* ............................................................ 4
Greenlee Contact Information........................................ 4
Tool Description.............................................................. 5
Specications................................................................. 5
Button & Feature Identication....................................... 6
LEDs, Icon & Decal Identication................................... 7
Table 1: Button Press & LED Guide................................ 8
Table 2: Icon & LED Guide.............................................. 9
Table 3: General Status LED Guide................................ 9
Training & Qualications............................................... 10
Pre-Operation Inspection ............................................. 10
Wireless Communication (Greenlee Link)..................... 10
Tool Set Up & Operation............................................... 11
Endpoint Mode ...................................................... 12
Repeater Mode ...................................................... 14
Transportation & Storage ............................................. 15
Charging....................................................................... 15
Cleaning ....................................................................... 15
Service.......................................................................... 15
Disposal........................................................................ 15
Table 3: Unit Troubleshooting....................................... 16
Table 4: LED Troubleshooting....................................... 17
Regulatory Statements................................................. 18

Pull Connect
352094539 REV 03 © 2024 Greenlee Tools, Inc.
This symbol means always wear safety
glasses with side shields or goggles
when handling or using this equipment to
reduce the risk of eye injury.
This symbol means read the operator’s
manual carefully before using the
equipment. The operator’s manual
contains important information on
the safe and proper operation of the
equipment.
This symbol means do not burn the
battery or expose to high heat to reduce
the risk of re or explosion.
This symbol means do not expose the
battery to water or rain to reduce the risk
of electric shock.
This symbol indicates the risk of tripping.
This symbol indicates the risk of electrical
shock.
This symbol means additional information
can be found here.
This symbol means do not lock foot switch
in ON position to reduce the risk of injury
from uncontrolled machine movement.
max
122°F/50°C
Loremipsum
This symbol means the battery
temperature should not exceed printed
temperature to reduce the risk of re or
explosion.
Safety Symbols Key
In this operator’s manual and on the product, safety
symbols and signal words are used to communicate
important safety information. This section is provided
to improve understanding of these signal words and
symbols.
This is the safety alert symbol. It is used
to alert you to potential personal injury
hazards. Obey all safety messages that
follow this symbol to avoid possible injury
or death.
indicates a hazardous situation which, if not avoided,
WILL result in death or serious injury.
indicates a hazardous situation which, if not avoided,
COULD result in death or serious injury.
indicates hazards or unsafe practices which, if not
avoided, MAY result in injury or property damage.

Pull Connect
52094539 REV 034© 2024 Greenlee Tools, Inc.
Safety Warnings
Greenlee Contact Information
If you have any questions or need to purchase parts/
accessories for this Greenlee product: Contact your
local Greenlee distributor or Greenlee’s Customer
Service Center.
Additional copies of this manual are available at
www.greenlee.com
Greenlee Customer Service
USA: 1-800-435-0786 | Canada: 800-435-0786
International: 1-815-397-7070
[email protected]
Shipping address:
Greenlee Factory Service Center
4411 Boeing Dr., Rockford, IL 61109
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery surfaces do
not allow for safe handling and control of the tool
in unexpected situations increasing the risk of injury
and tool damage.
• Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
Use the correct tool and accessories for your
application. The correct tool will do the job better
and safer at the rate for which it was designed.
Use of the tool for operations different from those
intended can result in a hazardous situation.
Before operating this tool, read and understand:
• This operator’s manual
• The instructions for any other equipment or
material used with this tool
• Markings on the tool
• Required work site safety procedures
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE.
• Do not lock foot switch in ON position. The
operator should always be in control of the tool
to decrease the risk of injury from uncontrolled
movement of the tool.
• Maintain communication between operators.
Loss of communication increases the risk of injury
and damage to the tool and cable.
• Do not use Pull Connect in Endpoint Mode outside
the immediate area of operation. One operator
should be located at each endpoint to monitor the
pull and control the foot switches to reduce the risk
of injury.
• Keep proper footing and balance at all times.
This enables better control of the power tool in
unexpected situations.
• Stay alert, watch what you are doing and use
common sense when operating a puller or feeder.
Do not use this equipment while you are tired or
under the inuence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
• Do not let familiarity gained from frequent use of
these tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
• Usethetoolin accordancewiththeseinstructions,
taking into account the working conditions and
the work to be performed. Use of the tool for
operations different from those intended could result
in a hazardous situation.
• Do not place Pull Connect on ground. Pull Connect
could be damaged and be a tripping hazard.
• Do not carry or unplug the foot switch or Pull
Connect by the cord. Continued abuse can lead to
damage to the cords. Damaged cords increase the
risk of electric shock.
• Do not use Pull Connect if wet. Moisture near
electronics increases the risk of injury and tool
damage from a short circuit.

Pull Connect
552094539 REV 03 © 2024 Greenlee Tools, Inc.
Tool Description
The Greenlee Pull Connect is a pulling accessory that communicates the status of the foot switch on Greenlee pullers
and 6810 feeder. It can operate using two modes, Endpoint and Repeater, that uses Greenlee Intelli-Pull™ technology
to send out and receive signals. Through the foot switch the Pull Connect can control the starting and stopping of the
puller and feeder simultaneously.
Features
• Intelli-Pull™ Technology
• Two Operating Modes: Endpoint and Repeater
• Compact and Rugged Design
• Magnets for Mounting Unit
• Simple and Easy to Read Control Panel
Specifications
Compatible with 6810 Feeder, UT-10, G10 and G6
Dimensions:..................................................................... ....9.0 in. x 5.0 in. x 1.6 in. (228.6 mm x 127.0 mm x 41.3 mm)
Weight: .................................................................................................................................................. 1.00 lb (0.45 kg)
Operating Temperature:....................................................................................................... 5°F to 122°F (-15°C to 50°C)
Storage Temperature (long term):........................................................................................50°F to 122°F (10°C to 50°C)
Contains FCC ID. ................................................................................................................. 2A3WE-XBPSX; SQGBL653
Contains IC......................................................................................................................... 28039-XBPSX; 3147A-BL653
Internal Li-Ion Battery
Nominal Voltage: .................................................................................................................................................... 3.63 V
Charging Temperature...........................................................................................................32°F to 113°F (0°C to 45°C)
Est. Charging Time.................................................................................................................................................... 5 hrs
Est. Operating Time................................................................................................................................................... 8 hrs
NOTICE To reduce the risk of electronics damage and reduced performance/product life, keep Pull Connect units
more than 6ft (2m) apart after channel is selected.
Intelli-Pull™ is a trademark of Greenlee Equipment, Inc.
All specifications are nominal and may change as design improvements occur.

Pull Connect
52094539 REV 036© 2024 Greenlee Tools, Inc.
1. Power Button
2. Mode Select Buttons
3. Radio Channel Buttons
4. Stop Button
7.
9.
5.
6
10
1
4
2
3
8
11
12
5. Charger Icon
6. Charger Input Jack
7. Foot Switch Icon
8. Foot Switch Jack
9. Patch Cord Icon
10. Patch Cord Jack
11. Mounting Magnets
12. Housing
Button & Feature Identification

Pull Connect
752094539 REV 03 © 2024 Greenlee Tools, Inc.
A. General Status LEDs (GREEN/RED)
B. Power Status LED (GREEN/RED)
C. Stop Signal LEDs (RED)
D. Mode Select LEDs (WHITE)
E. Feeder Icon
F. Feeder Foot Switch LED (GREEN)
LEDs, Icon & Decal Identification
A
A
A
A
P
C
B
D
FJ
L
O
I
M
G. Repeater Mode Icon
H. Puller Icon
I. Puller Foot Switch LED (GREEN)
J. Radio Channel LEDs (GREEN)
K. Signal Strength Icons
L. Signal Strength LEDs (GREEN)
M. Wireless LED (BLUE)
N. Battery Icon
O. Battery LEDs (GREEN/RED)
P. Product Information Decal
H
G
E
K
N
CHARGER: USB 5V 1A
Use provided charger only
Solo use el cargador provisto
Utilisez uniquement le chargeur fourni
Do not use foot switch in repeater mode
No utilice el interruptor de pie en modo repetidor
N'utilisez pas la pédale en mode répéteur
52093562 REV 6
Color: CMYK
Material: Empire E-214WVL per UL Standard
5.48" R 0.15”
2.98"
Energía
Puissance
1.Power 2.Mode
Modo
Mode
Press To Stop
Hold To Resume
(Repeater Mode)
Pulsar para Detener
Mantener Pulsado para Reanudar
Appuyez pour Arrêter
Maintenez pour Reprendre
Serial Number:
Model: RGPC01
Additional Info
Select the same channel for all units.
Seleccione el mismo canal para todas las unidades.
Sélectionnez le même canal pour toutes les unités.
3.Channel
Canal
Canal
Presione ambos interruptores de pie para moverse.
Appuyez sur les deux pédales pour le mouvement.
4.Press both foot switches to start.
No lo coloque en el suelo para obtener la mejor señal.
Ne pas placer sur le sol pour le meilleur signal.
For best signal, do not place on ground.
Solid Signal Bars = Connection.
Las barras de señal sólidas significan conexión.
Des barres de signal solides signifient une connexion.
CONTAINS FCC ID: 2A3WE-XBPSX
CONTAINS FCC ID: SQGBL653
CONTAINS IC: 28039-XBPSX
CONTAINS IC: 3147A-BL653
Patents:
pat.Greenlee.com
52093562 REV 6
Greenlee Tools, Inc.
4455 Boeing Drive,
Rockford, Illinois 61109 GREENLEE.COM/US/EN/PULL-CONNECT
= Diecut = Clear Film Window
BC
P.

Pull Connect
52094539 REV 038© 2024 Greenlee Tools, Inc.
TABLE 1: BUTTON & LED GUIDE
ID BUTTON ACTION LEDs BEHAVIOR & COLOR MEANING
1
Power
Button
Press and Hold 4 sec.
to turn ON
ALL
All LEDs turn ON then OFF
except Power Status, Battery
Level & Operating Mode LEDs
stay ON.
Start Up Sequence
Power Status LED
Solid GREEN Unit is ON
Flashing RED See Troubleshooting
Operating Mode LEDs 3 Flashing White
This unit is waiting for the operator to
select a mode.
Press and Hold 2 sec.
to turn OFF ALL
OFF Unit is OFF
2
3 Mode
Select
Buttons
Press Mode Select
Button next to Feeder
Icon
Feeder Mode LED
Feeder is Solid White and the
others are OFF
This unit is set to Feeder Mode.
Repeater Mode LED OFF
Radio Channel LEDs All are Flashing GREEN
Operator can select a radio channel.
Press Mode Select
Button next to Puller
Icon
Puller Mode LED
Puller LED is Solid White and
the others are OFF
This unit is set to Puller Mode.
Repeater Mode LED OFF
Radio Channel LEDs All are Flashing GREEN
Operator can select a radio channel.
Press Mode Select
Button next to
Repeater Icon
Repeater Mode LED Solid White
This unit is set to Repeater Mode.
Feeder/Puller Mode LEDs Alternating White
Radio Channel LEDs All are Flashing GREEN
Operator can select a radio channel.
3
3 Radio
Channel
Buttons
Press 1, 2, or 3. Must
be the same as other
units in system. Radio Channel LEDs
Selected button LED is Solid
GREEN the others are OFF
The radio is broadcasting on this channel.
4
Stop
Button
Press to Stop Pull. Stop Signal LEDs
Flashing RED This unit is broadcasting a STOP signal.
Solid RED
Another unit is broadcasting a STOP signal.
The STOP command can only be cleared
on the original unit.
Press and hold until
flashing Stop Signal
LEDs turn OFF. Stop Signal LEDs
OFF
STOP command is cleared. Operators
must step off then back on to foot
switch to resume pull.
Press after start up
sequence and before
selecting operating
mode.
Wireless LED
Flashing BLUE
Connection with Greenlee Link app
possible.
Solid BLUE Connected with Greenlee Link app.

Pull Connect
952094539 REV 03 © 2024 Greenlee Tools, Inc.
TABLE 3: ICON & LED GUIDE
LED ID ICON BEHAVIOR & COLOR MEANING
Feeder Endpoint
LED
OFF The feeding endpoint foot switch is NOT depressed.
Solid GREEN The feeding-endpoint foot switch is depressed.
Flashing GREEN A Pull Connect, on the same channel, is issuing a STOP command.
Puller Endpoint LED
OFF The puller endpoint foot switch is NOT depressed.
Solid GREEN The puller endpoint foot switch is depressed.
Flashing GREEN A Pull Connect, on the same channel, is issuing a STOP command.
Signal Strength
LEDs
GREEN LEDs Sweep Back and Forth This Pull Connect is searching for compatible signals on the selected
channel.
1 to 5 LEDs Solid GREEN Shows the connection strength to the other feeder/puller endpoint.
Switching Between Different Number of
GREEN LEDs
This Pull Connect is in Repeater Mode and shows the connection strength
of the indicated Feeder or Puller endpoint.
Wireless LED
Flashing BLUE Connection to Greenlee Link app available.
Solid BLUE Connected to Greenlee Link app.
Battery LEDs
1-3 Segments are Solid GREEN Shows the battery charge level.
Bottom Segment is Rapidly Flashing
GREEN Battery is low, charge this Pull Connect.
One or More Segments are Slowly
Flashing GREEN Pull Connect is charging.
TABLE 2: GENERAL STATUS LED GUIDE
LED ID LED BEHAVIOR & COLOR MEANING
General Status
LEDs
Flashing GREEN The Pull Connect is connected to the other endpoint and ready to operate.
Equipment is not active.
Rotating GREEN Both endpoint foot switches are depressed and equipment is in motion.
Flashing RED A STOP signal is broadcasting from this unit.
All equipment is stopped in system.
Solid RED A STOP signal is active on another unit in the system.
All equipment is stopped in system.
OFF No active connections.

Pull Connect
52094539 REV 0310 © 2024 Greenlee Tools, Inc.
• Daily before use, inspect the tool and correct
any problems before using. If any problems are
found, do not use this tool until the problems have
been xed. Failure to follow these steps increases
the risk of injury.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Pre-Operation Inspection
1. Clean any oil, grease, or dirt from the body and
buttons. A clean tool aids inspection and helps the
operator observe the lights to see the status of the
tool.
2. Look for wear or damage, such as cracks, gouges,
or chips to housing.
3. Check for the presence and condition of decals.
4. Inspect the patch and foot switch cords for damage
and disentangle before use. Never use the cord for
carrying, pulling or unplugging from equipment.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
5. For Endpoint mode: Check that the foot switch is
present and in good condition and does not stick
when depressed on.
6. Inspect any other equipment in the system according
to their instruction manuals.
7. Check work area for adequate lighting, a clear, level,
stable and dry place for all equipment.
Wireless Mode
The blue Wireless LED indicates information related to
wireless connection status. The Pull Connect wireless
technology connects to the Greenlee®Link app using a
smartphone or tablet running iOS or Android operating
systems.
To enable wireless connection to the Greenlee® Link app:
1. Download the appropriate Greenlee® Link app to
your device by going to Greenlee.com/apps, the
Google Play Store or the Apple App Store.
2. Turn ON Pull Connect, wait for start up sequence to
nish and Mode Select LEDs start ashing white. Do
not press any of the Mode Select Buttons.
3. Press the Stop Button. When the blue Wireless LED
starts ashing the unit is able to connect to the app.
(Fig. 1)
4. Go into the Greenlee Link app and follow the
instructions to select the serial number of the Pull
Connect in Wireless Mode to start pairing.
5. Wait for the Wireless LED to become solid blue
signalling the unit is connected. The Greenlee Link
app can be used to view data from the Pull Connect
and initiate rmware updates.
The Pull Connect cannot be used for Connected Pulling
while in Wireless Mode. Turn OFF Pull Connect to
exit Wireless Mode. When next turned ON follow the
instructions for the Connected Pulling Modes shown in
this manual.
Figure 1
Training & Qualifications
Only workers trained and qualied should use this tool,
especially in a live line environment. It is recommended
at least a second trained and qualied person is present
at appropriate distance to respond if needed. Follow all
training and proper job site safety precautions outlined
by your industry, government and employer.