GreenWorks JSD401 User manual

1
2
10
3
4
5
6
7
8
9
1. 2. 3.
4. 5. 6.
7.
JSD401

JSD401 www.greenworksaustralia.com
Greenworks Australia
A Division Jak Max P/L
380 Foley’s Road Derrimut
Victoria, Australia 3026
EN OPERATOR MANUALJIG SAW
3601407AU

1 Description......................................... 2
1.1 Purpose.............................................................. 2
1.2 Overview........................................................... 2
1.3 Packing list........................................................ 2
2 Introduction....................................... 2
2.1 Intended use.......................................................2
3 General power tool safety
warnings............................................. 2
3.1 Work area safety................................................ 2
3.2 Electrical safety................................................. 2
3.3 Personal safety...................................................2
3.4 Power tool use and care..................................... 3
3.5 Battery tool use and care................................... 3
3.6 Service............................................................... 3
4 Specific safety warnings....................3
5 Symbols on the product.................... 4
6 Risk levels...........................................4
7 Recycle................................................5
8 Installation......................................... 5
8.1 Unpack the machine.......................................... 5
8.2 Install the battery pack.......................................5
8.3 Remove the battery pack................................... 5
8.4 Install the blade..................................................5
8.5 Remove the blade.............................................. 5
8.6 Install the edge guide.........................................5
9 Operation........................................... 5
9.1 Start the machine............................................... 6
9.2 Stop the machine............................................... 6
9.3 Orbital motion....................................................6
9.4 Adjust the footplate angle..................................6
9.5 Operate the machine.......................................... 6
10 Maintenance.......................................6
10.1 Clean the machine............................................. 6
10.2 General manintenance....................................... 7
11 Technical data.................................... 7
12 Warranty............................................ 7
1
English EN

1 DESCRIPTION
1.1 PURPOSE
You may use this product for cutting purposes:
• cutting all types of wood
• cutting plastic
• cutting metals
1.2 OVERVIEW
Figure 1.
1Trigger
2Tube
3Angle Adjustment
Trigger
4Footplate
5Blade Orbit Selector
Lever
6Blade
7Edge Guide Knobs
8Edge Guide
9Finger Guard
10 Lock-off Button
1.3 PACKING LIST
1Jig saw
2Dust tube
3Edge guide
4Wood blade
5Steel blade
6Footplate
7Manual ( operation
manual, figure sheet )
2 INTRODUCTION
Your product has been engineered and manufactured to high
standards for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of
rugged, trouble-free performance.
2.1 INTENDED USE
The machine is used for
• cutting all types of wood
• cutting plastic
• cutting drywall
3 GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or BATTERY-operated
(cordless) power tool.
3.1 WORK AREA SAFETY
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
3.2 ELECTRICAL SAFETY
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges and moving
parts. Damaged or entangled cords increase the risk of
electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a RESIDUAL CURRENT DEVICE
(RCD) protected supply. Use of an RCD reduces the risk
of electric shock.
3.3 PERSONAL SAFETY
•Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A lapse of attention
while operating power tools may result in serious
personal injury.
•Use personal protection. Always wear eye protection.
Protective products such as dust mask, non-skid safety
shoes, hard hat or hearing protection used appropriately
will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in
the off position before connecting to power source
and/or battery pack and when picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch on
invites accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
2
English
EN

•Do not over-reach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
•Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust related hazards.
•Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury
within a fraction of a second.
3.4 POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
•Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
•Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
3.5 BATTERY TOOL USE AND CARE
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or fire.
•Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with plenty of soap and water. If liquid
contacts eyes, immediately seek medical help. Liquid
ejected from the battery may cause irritation or burns.
•Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or
risk of injury.
•Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C may cause explosion.
•Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
3.6 SERVICE
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
•Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
4 SPECIFIC SAFETY WARNINGS
•Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
•Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
•Know your power tool. Read operator manual
carefully.Learn its applications and limitations, as well
as the specific potential hazards related to this power
tool. Obey this instruction will reduce shock, fire or
serious injury.
•Always wear safety glasses with side shields marked to
comply with ANSI Z87.1.Obey this instruction will
reduce the risk of serious injury.
•Protect your lungs. Wear a face or dust mask if the
operation is dusty.Obey this instruction will reduce the
risk of serious injury.
3
English EN

•Protect your hearing. Wear hearing protection during
extended periods of operation.Obey this instruction will
reduce the risk of serious injury.
•Battery tools do not have to be plugged into an
electrical outlet; thus, they are always in operating
condition. Be aware of possible hazards when not
using your battery tool or when changing
accessories.Obey this instruction will reduce the risk of
electric shock , fire, or serious injury,
•Do not place battery tools or their batteries near fire
or heat.This will reduce the risk of explosoion and
possibl injury.
•Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow.A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
•Batteries can explode in the presence of a source of
ignition, such as a pilot light. To reduce the risk of
serious injury, never use any cordless product in the
presence of open flame.An exploded battery can propel
debris and chemicals. If exposed, flush with water
immediately.
•Do not charge battery tool in a damp or wet
location.Obey this instruction will reduce the risk of
electric shock.
•For best results, your battery tool should be charged
in a location where the temperature is more than 50°F
but less than 100°F.To reduce the risk of serious injury,
do not store outside or in vehicles.
•Under extreme usage or temperature conditions,
battery leakage may occur.If liquid comes in contact
with your sink, wash immediately with soap and water. If
liquid gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Obey this instruction will reduce the risk of
serious injury.
•Keep these instructions. Refer to them frequently and
use them to instruct others who may use this tool.If
you borrow someone this tool, loan them these
instructions also to prevent incorrect use of the machine
and possible injury.
5 SYMBOLS ON THE PRODUCT
Some of the following symbols may be used on this tool.
Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the
tool better and safer.
Symbol Explanation
V Volts
min-1 No-load speed
Direct current
Safety alert
Symbol Explanation
Read and understand all instructions
before operating the product, and fol-
low all warnings and safety instruc-
tions.
Wear ear protection.
Wear eye protection
Do not expose the product to rain or
moist conditions.
Wear a dust mask
No Hands Symbol
No Hands Symbol
No Hands Symbol
Hot Surface
6 RISK LEVELS
The following signal words and meanings are intended to
explain the levels of risk associated with this product.
SYM-
BOL
SIGNAL MEANING
DANGER Indicates an imminently haz-
ardous situation, which, if not
avoided, will result in death
or serious injury.
WARNING Indicates a potentially hazard-
ous situation, which, if not
avoided, could result in death
or serious injury.
CAUTION Indicates a potentially hazard-
ous situation, which, if not
avoided, may result in minor
or moderate injury.
CAUTION (Without Safety Alert Sym-
bol) Indicates a situation that
may result in property dam-
age.
4
English
EN

7 RECYCLE
Separate collection. You must not discard
with usual household waste. If it is necessa-
ry to replace the machine, or if it is no more
use to you, do not discard it with household
waste. Make this machine available for sepa-
rate collection.
Separate collection of used machine and
packaging let you recycle materials and use
them again. Use of the recycled materials
helps prevent environmental pollution and
decreases the requirements for raw materi-
als.
At the end of their useful life, discard batter-
ies with a precaution for our environment.
The battery contains material that is danger-
ous to you and the environment. You must
remove and discard these materials separate-
ly at a equipment that accepts lithium-ion
batteries.
8 INSTALLATION
8.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine before
use.
WARNING
• If parts of the machine are damaged, do not use the
machine.
• If you do not have all the parts, do not operate the
machine.
• If the parts are damaged or missing, contact the service
center.
1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local
regulations.
8.2 INSTALL THE BATTERY PACK
Figure 2.
WARNING
• If the battery pack or charger is damaged, replace the
battery pack or the charger.
• Stop the machine and wait until the motor stops before
you install or remove the battery pack.
• Read, know, and do the instructions in the battery and
charger manual.
1. Align the lift ribs on the battery pack with the grooves in
the battery compartment.
2. Push the battery pack into the battery compartment until
the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
8.3 REMOVE THE BATTERY PACK
Figure 2.
1. Push and hold the battery release button.
2. Remove the battery pack from the machine.
8.4 INSTALL THE BLADE
Figure 3.
1. Remove battery pack.
2. Rotate the blade clamp lock counterclockwise. Hold the
lock in the open position.
3. Insert saw blade between blade clamp and saw bar.
4. Close blade clamp lock.
5. Reinstall the battery pack.
8.5 REMOVE THE BLADE
Figure 3.
1. Remove battery pack.
2. Rotate the blade clamp lock counterclockwise. Hold the
lock in the open position.
3. Remove the saw blade.
8.6 INSTALL THE EDGE GUIDE
Figure 4.
Put the edge guide through the two slots in the base of the
machine.
Adjust to the necessary width and lock in place with the edge
guide screw.
9 OPERATION
WARNING
Always wear eye protection.
5
English EN

WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
9.1 START THE MACHINE
Figure 5.
NOTE
The machine can not work when the lock-off button is on
the center.
1. Push the lock-off button to the left or right side to unlock
the trigger.
2. Pull the trigger to turn the machine ON.
Variable speed
The machine has a variable speed switch that delivers higher
speed with increased trigger pressure and lower speed with
decreased trigger pressure.
9.2 STOP THE MACHINE
Figure 5.
1. Release the switch trigger.
9.3 ORBITAL MOTION
Orbital motion provides faster, more effcient cutting.
Choose from four orbital adjustment position for fine to
aggressive cutting.
0
1
2
3
0
Hard materials such as metals or thin sheet
metals. This setting can be used with knife
blades, grit edge blades, rasp work, and
down cutting blades.
0
1
2
3
1
Soft materials where cleaner cutting or del-
icate scrolling work is performed.
0
1
2
3
2
Medium density materials such as harder
woods or particle board.
0
1
2
3
3
Soft materials such as wood, plastics, etc.
and when fast cutting is more important
than a clean cut.
9.4 ADJUST THE FOOTPLATE ANGLE
Figure 6.
The footplate may be tilted to allow angle cuts up to 45° in
either direction.
1. Switch the trigger to the right.
2. Adjust the angle as needed.
3. Switch the trigger to the original position.
9.5 OPERATE THE MACHINE
Figure 7.
NOTE
For best performance, always select a specified blade for
the particular application and type of material you wish to
cut.
General cutting
1. Put the front of the saw base on the workpiece
2. Align cutting edge of the blade with the line on your
workpiece
3. Start the saw and move it forward on the work surface.
Plunge cutting
1. Make the line of cut clearly on the workpiece.
2. Set the cutting blade at 0.
3. Put the front of the saw base on the workpiece
4. Use high speed to start the machine and slowly lower the
blade into the workpiece until the blade cuts through the
wood.
WARNING
To decrease the risk of injury, keep hands away from the
blade and all moving parts. Always wear safety gloves or
glasses with side shields.
10 MAINTENANCE
CAUTION
Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
WARNING
Remove the battery pack from the machine before
maintenance.
10.1 CLEAN THE MACHINE
CAUTION
The machine must be dry. Humidity can cause risks of
electrical shocks.
6
English
EN

• Clear the unwanted material out of the air vent with a
vacuum cleaner.
• Do not spray the air vent or put the air vent in solvents.
• Clean the housing and the plastic components with a
moist and soft cloth.
10.2 GENERAL MANINTENANCE
• Before each use, examine the machine for damaged,
missing, or loose parts such as screws, nuts, bolts and
caps.
• Clean the machine with a dry cloth. Do not use slovents.
WARNING
Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
CAUTION
Use only approved replacement parts.
11 TECHNICAL DATA
Voltage 24 V
Strokes per minute 0-3000 min-1
Cutting angle 0-45°
Orbital motion 4 settings
Blade changing Tool-Free
Weight without battery 2.2 kg
Battery model G24B2/G24B4 and other
BAG series
Charger model 2913907 and other CAG ser-
ies
Measured sound pressure
level
88.5dB(A), KpA= 3 dB(A)
Measured sound power level 99.5dB(A), KwA= 3 dB(A)
Vibration 4.2 m/s2, K = 1.5 m/s2
The recommended ambient temperature range:
Item Temperature
Appliance storage tempera-
ture range
32°F (0°C) - 113°F (45°C)
Appliance operation temper-
ature range
32°F (0°C) - 113°F (45°C)
Battery charging temperature
range
39°F (4°C) - 104°F (40°C)
Charger operation tempera-
ture range
39°F (4°C) - 104°F (40°C)
Item Temperature
Battery storage temperature
range
32°F (0°C) - 113°F (45°C)
Battery discharging tempera-
ture range
32°F (0°C) - 113°F (45°C)
12 WARRANTY
(The full warranty terms and conditions can be found on
Greenworks webpage)
The Greenworks warranty is 4 years on the product, and 2
years on batteries (consumer/private usage) from the date of
purchase. This warranty covers manufacturing faults. A faulty
product under warranty might be either repaired or replaced.
A unit that has been misused or used in other ways then
described in the owner’s manual might be rejected for
warranty. Normal wear, and wear parts are not considered as
warranty. The original manufacturer warranty is not affected
by any additional warranty offered by a dealer or retailer.
A faulty product must be returned to the point of purchase in
order to claim for warranty, together with the proof of
purchase (receipt).
7
English EN