GREISINGER GLMU 400 MP-UNI User manual

Operating Manual
Conductivity-Transmitter
without measuring cell
GLMU 400 MP -UNI
Keep for later use.
www.ghm-group.de
Companies / Brands of the GHM
Englisch

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 2 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
Inhalt
1General Advice ______________________________________________________________________ 3
2Intended use ________________________________________________________________________ 3
2.1 Safety signs and symbols __________________________________________________________________3
2.2 Safety Instructions _______________________________________________________________________3
3Installation _________________________________________________________________________ 4
3.1 Dimensions _____________________________________________________________________________4
3.2 Assignment of elbow-type plug _____________________________________________________________4
3.3 Terminal assignment of meas. cell socket _____________________________________________________4
3.4 Usage of Unit-Labels ______________________________________________________________________5
4Operation __________________________________________________________________________ 5
4.1 General information about the conductivity measuring__________________________________________5
4.1.1 The measuring cell ________________________________________________________________________________ 5
4.1.2 Measuring hints __________________________________________________________________________________ 5
4.1.3 Temperature compensation ________________________________________________________________________ 5
4.1.4 Salinity measuring ________________________________________________________________________________ 6
4.1.5 TDS measuring ___________________________________________________________________________________ 6
5Display functions ____________________________________________________________________ 6
5.1 Currently measured values_________________________________________________________________6
5.1.1 Min/Max Value Memory ___________________________________________________________________________ 6
6Error and system messages ____________________________________________________________ 6
7Configuration _______________________________________________________________________ 8
7.1 'C.rnG': Setting of Cell Constant: Cell constant range ____________________________________________8
7.2 'CELL': Setting of the cell-constant of the connected measuring cell ________________________________8
7.3 'Func': Setting of the measuring function _____________________________________________________8
7.4 'rAnG': Setting of the measuring range (not at “Func SAL”) _______________________________________8
7.5 't.Cor': Setting of temperature compensation method (not at “Func SAL”) __________________________9
7.6 't.Lin': Setting of temperature coefficient (only for t.Cor = Lin) ____________________________________9
7.7 't.rEF': Setting of reference temperature (only for t.Cor = nLF or Lin) _______________________________9
7.8 'C.tdS': Setting of TDS-factor _______________________________________________________________9
7.9 't.InP' t-Input: Temperatureinput____________________________________________________________9
7.10 'dA.Lo': Display at zero output (output scaling) ________________________________________________9
7.11 'dA.Hi': Display at maximum output (output scaling) ____________________________________________9
7.12 'Unit' with Temp-arrow: Temperature unit ____________________________________________________9
7.13 'OFFS' with Temp-arrow: Offset of temperature measuring ______________________________________9
7.14 'SCAL' with Temp-arrow: Scale correction of temperature measuring ______________________________9
8Reshipment and Disposal_____________________________________________________________ 10
8.1 Reshipment ____________________________________________________________________________10
8.2 Disposal instructions_____________________________________________________________________10

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 3 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]

9Calibration Services _________________________________________________________________ 10
10 Specification _____________________________________________________________________ 10
11 Variants/ Measuring Cells and Accessories _____________________________________________ 11
1 General Advice
Read this document carefully and get used to the operation of the device before you use it. Keep this docu-
ment within easy reach near the device for consulting in case of doubt.
Mounting, start-up, operating, maintenance and removing from operation must be done by qualified, specially
trained staff that have carefully read and understood this manual before starting any work.
The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended
one, ignoring this manual, operating by unqualified staff as well as unauthorized modifications to the device.
The manufacturer is not liable for any costs or damages incurred at the user or third parties because of the
usage or application of this device, in particular in case of improper use of the device, misuse or malfunction
of the connection or of the device.
The manufacturer is not liable for misprints.
2 Intended use
The GLMU 400 MP-UNI is a universal transmitter for measuring conductivity or other units based on conduc-
tivity measuring in liquids.
The measurement is performed by means of alternating current flow between the poles of the measuring
cell, being in direct contact with the liquid.
The measurement is displayed via analogue standard signal output and a liquid crystal display.
The 4-20 mA model is supplied by the current loop, the 0-1 or 0-10 V model requires separate power supply.
The configuration of the various parameters has to be checked prior to use.
The measuring cell is included in the scope of supply and prior to measuring a suitable cell has to connected
and configured.
2.1 Safety signs and symbols
Warning notices are marked in this manual as shown below:
DANGER
Warning! Symbol warns of impending danger, death, serious
bodily injury or serious property damage if ignored.
Attention! Symbol warns of potential hazards or hazardous situa-
tions that can cause damage on the equipment or the environ-
ment if ignored.
Note! Symbol indicates incidents that have an indirect impact on
the operation or can trigger an unforeseen reaction if ignored.
2.2 Safety Instructions
This device has been designed and tested in accordance to the safety regulations for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures
and special safety advises given in this manual will be adhered to when using it.
1. Trouble-free operation and reliability of the device can only be guaranteed if it is not subjected to any
other climatic conditions than those stated under “Specification”.
Transporting the device from a cold to a warm environment condensation may result in a failure of the
function. In such a case make sure the device temperature has adjusted to the ambient temperature be-
fore trying a new start-up.

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 4 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
2. General instructions and safety regulations for electric, light and heavy current plants, including domestic
safety regulations (e.g. VDE), have to be observed.
3. Whenever there may be a risk whatsoever involved in running it, the device has to be
switched off immediately and to be marked accordingly to avoid re-starting. Operator safety
may be a risk if:
- there is visible damage to the device
- the device is not working as specified
- the device has been stored under unsuitable conditions for a longer time
In case of doubt, please return device to manufacturer for repair or maintenance.
4. Do not use this product as safety or emergency stop device or in any other application where
failure of the product could result in personal injury or material damage.
Failure to comply with these instructions could result in death or serious injury and material
damage.
3 Installation
3.1 Dimensions
General elbow-type plug installation instructions
To mount the connection cable (2-, or 3-wire depending on type of
device) the elbow-type plug screw has to be loosened and the cou-
pling insert has to be removed by means of a screw driver at the
position indicated (arrow).
Pull out connection cable through glanding and connect to the
loose coupling insert as described in the wiring diagram.
Replace loose coupling insert onto the pins at the transmitter hous-
ing and turn cover cap with cable outlet in the direction desired untill
it snaps on (4 different starting positions at 90° intervals).
Re-tighten the screw at the angle plug.
3.2 Assignment of elbow-type plug
4-20 mA (2-wire-connection).
voltage (3-wire connection).
1 = supply +
2 = GND / signal
1 = signal +
3 = supply +Uv
(4) = supply -Uv
The type current or voltage output is set by works and cannot be changed
3.3 Terminal assignment of meas. cell socket
contact no.
2 pole-cell
4 pole-cell
1
temperature +
temperature +
2
temperature GND
temperature GND
3
supply 1 (electrode 1)
supply 1 (outer electrode 1)
4
signal 1 (electrode 1)
signal 1 (outer electrode 1)
5
signal 2 (electrode 2)
signal 2 (inner electrode 2)
6
supply 2 (electrode 2)
supply 2 (inner electrode 2)
7
not used
not used
DANGER
DANGER

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 5 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
3.4 Usage of Unit-Labels
As the transmitter is a multiple purpose device, many different display units are possi-
ble, e.g. µS/cm, kOhm·cm.
Therefore unit-labels (within scope of supply) can be shoved between the case cover
and the front foil behind the transparent unit-window.
To replace a label, unscrew the cover, pull out the old label (if present) and shove in the
new one.
The unit depends on the settings of the Cell-constant, the function and the measuring range!
Please refer to table in chapter “Configuration of the device”
4 Operation
4.1 General information about the conductivity measuring
4.1.1 The measuring cell
During the measurement, the conductivity measuring cell must be dipped at least in so far, that at least the
electrodes and the integrated temperature sensor is “under water”.
Example for measuring cell without thread: Practical immersion depth 30...110 mm.
The measuring cell can either be stored dry or in water. After dry storage a “wetting time” has to be consid-
ered until the final precision is achieved.
Attention: Measuring cells with graphite electrodes must never come into contact with water-
repellent materials such as oil or silicone.
If conductivity measured is much higher or lower than expected this may be due to the measuring being
soiled with non-conducting or conducting extraneous materials. The measuring cell has to be cleaned e.g.
with a watery soap solution.
When measuring media at low conductivity the measuring cell has to get sufficient flow.
GLMU 200 MP: cost optimized 2 pole cell, suitable e.g. for pure water / drinking water / sweat water
GLMU 400 MP: 4 pole cell, especially suitable for applications above 2000 µS/cm e.g. sewage water, sea
water etc.
4.1.2 Measuring hints
Conductivity measuring is comparably easy to perform, the precision of the instrument is very constant if it is
used as intended. Depending on the necessary accuracy the instruments can be used up to several years
without re-calibration of the cell constant.
If the accuracy should be controlled or improved, this is done by means of suitable reference solutions and
the adjusting of the cell factor.
Attention! Wrong handling of reference solution can make them useless very fast.
4.1.3 Temperature compensation
The conductivity of aqueous solution is temperature dependent. The dependency itself is strongly dependent
on the kind of solution. For the most applications e.g. in fish farming etc., the non linear temperature com-
pensation of natural waters is precise (“nLF” according to EN 27888). The most common reference tempera-
ture is 25 °C.

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 6 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
Arrow to Temp indicates
temperature display
4.1.4 Salinity measuring
The salinity (salt content) of seawater can be determined in the measuring mode „SAL“ (basis: International
Oceanographic Tables; IOT)
The salinity of standard-seawater is 35 ‰ (35 g salt per 1 kg seawater).
The values are displayed in ‰ or g/kg, an additional commonly used unit for this value is “PSU“ (Practical
Salinity Unit).
4.1.5 TDS measuring
At the TDS measuring the dry residues or total dissolved solids value is calculated by means of the conduc-
tivity and a calculation factor (C.tdS). This factor has to be evaluated for the referring type of solution.
The values are displayed in mg/l.
5 Display functions
5.1 Currently measured values
During normal operation the conductivity display value is displayed.
By short press of key ‘SET’ (1) the temperature in [°C] will displayed for 10 seconds.
display of conductivity value display temperature
5.1.1 Min/Max Value Memory
watch Min values (Lo): press ‘down‘(2) shortly once display changes between ‘Lo‘ and Min values
watch Max values (Hi): press ‘up‘(3) shortly once display changes between ‘Hi‘ and Max values
restore current values: press ‘down‘(2) or ’up’(3) once again current values are displayed
clear Min-values: press ‘down’(2) for 2 seconds Min values are cleared. The display shows shortly ‘CLr‘.
clear Max-values: press ‘up’(3) for 2 seconds Max values are cleared. The display shows shortly ‘CLr‘.
After 10 seconds the currently measured values will be displayed again.
6 Error and system messages
Display
Description
Possible fault cause
Remedy
Err.1
measuring range exceed-
ed
Wrong signal
Temperature above 140°C not allowed.
Choose right measuring range for con-
ductivity
Err.2
Measuring value below
measuring range
Wrong signal
Temperature below -5°C not allowed.
Choose right measuring range for con-
ductivity
Err.7
System fault
Error in device
Disconnect from supply and reconnect.
If error remains: return to manufacturer
Err.9
Sensor error
Sensor or cable defective
Check sensor, cable and connections
Er.11
Calculation not possible
Calculation variable miss-
ing or invalid
Check temperature
Er.12
Measuring Cell fault
Cell cannot be driven
Clean/Restart or return to manufacturer
Er.13
Measuring Cell fault
Cell cannot be driven
Clean/Restart or return to manufacturer

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 7 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
8.8.8.8
Segment test
The transducer performs a display test for 2 seconds after power up.
After that it will change to the display of the measuring.

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 8 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
7 Configuration
In the configuration the devices parameters can be changed.
The jumper has to be set, p.r.t. figure right hand side. To set or
remove jumper, the housing cover has to be removed. Ex works
the jumper is set.
To change parameters press “SET” (key 1) two seconds, then the
parameter selection is started with the first parameter (display
shows “C.rnG”).
By pressing “SET” the desired parameter is selected, the editing of
the parameter values happens via keys (key 3) or (key 2).
Pressing “SET” again (after editing the parameter values) returns
to the parameter selection
Pressing “SET” again after the last parameter finishes the configu-
ration, stores the changes and restarts the device.
7.1 'C.rnG': Setting of Cell Constant: Cell constant range
0.01
Purewater, cells with K = 0.003…0.012
0.1
Purewater, cells with K =0.03…0.12
1
Standard cells with K = 0.3 … 1.2
10
Cells with K =3…12
7.2 'CELL': Setting of the cell-constant of the connected measuring cell
Possible inputs: 0.300...1.200
Cell constant K = C.rnG * CELL (Unit is 1/cm)
Example : Cell with K = 0.412: 'C.rnG' = 1, CELL = 0.412
Cell with K = 0.120: 'C.rnG' = 0.1, CELL = 1.200
Cell with K = 0.22: not supported
7.3 'Func': Setting of the measuring function
Possible inputs: cond conductivity
reSi: resistivity
tdS: TDS (total dissolved solids
SAL: Salinity = salt content of sea water
7.4 'rAnG': Setting of the measuring range (not at “Func SAL”)
The measuring range is depending on the function set above. Possible inputs:
C.rnG = 0.01
Range (rAnG) r 4
Bereich (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 5000 µS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
0.00 –20.00 µS/cm
0.000 –2.000 µS/cm
Resistivity (rESi)
1 - 5000 Ohm·cm
0.00 -20.00 kOhm·cm
0 - 200 kOhm·cm
0 - 2000 kOhm·cm
TDS (tdS)
0.00 –20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
0.00 –20.00 mg/l
0.000 –2.000 mg/l
C.rnG = 0.1
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0.00 - 50.00 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
0.00 –20.00 µS/cm
Resistivity (rESi)
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00-20.00 kOhm·cm
0 - 200 kOhm·cm
0 - 2000 kOhm·cm
TDS (tdS)
0.0 –200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
0.00 –20.00 mg/l
C.rnG = 1
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 500 mS/cm
0.0 - 200.0 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
Resistivity (rESi)
1.00 - 50.00 Ohm·cm
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00 - 20.00 kOhm·cm
0 - 200 kOhm·cm
TDS (tdS)
0 - 1000 g/l
0.0 - 200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
Salinity (SAL)
0.0 - 70.0
C.rnG = 10
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 5000 mS/cm
0 - 2000 mS/cm
0.0 - 200.0 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
If the jumper is removed from the
shown contacts, the configura-
tion is inaccessible,
values are protected.

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 9 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
Resistivity (rESi)
0.10 - 5.000 Ohm·cm
1.00-50.00 Ohm·cm
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00-20.00 kOhm·cm
TDS (tdS)
0 - 2000 g/l
0.0 - 200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
7.5 't.Cor': Setting of temperature compensation method (not at “Func SAL”)
Possible inputs: off: no temperature compensation
nLF:non linear compensation for natural water according to EN 27888 (DIN 38404).
For measurings of ground and surface water, drinking water or pure water.
Attention: restricted temperature range: -5..105 °C
Lin: linear temp. compensation (for other aqueous solutions, factor has to be entered)
7.6 't.Lin': Setting of temperature coefficient (only for t.Cor = Lin)
Possible input: 0.300 .. 5.000 [%]
If it is only measured in a narrow conductivity range, the temperature compensation factor of this range can
be determined.
7.7 't.rEF': Setting of reference temperature (only for t.Cor = nLF or Lin)
Possible input: 20 °C or 25 °C
7.8 'C.tdS': Setting of TDS-factor
Calculation factor for TDS (Total Dissolved Solids)-measurements, possible input: 0.40 .. 1.00.
The calculation factor depends on the composition of the medium and has to be determined for each type.
7.9 't.InP' t-Input: Temperatureinput
ntc: NTC 10k / Pt: Pt1000
7.10 'dA.Lo': Display at zero output (output scaling)
Enter the display value at which the output should have 4 mA (or 0 V).
The value range is depending on the selected measuring function (Func) and range (rAnG).
7.11 'dA.Hi': Display at maximum output (output scaling)
Enter the value at which the output should have 20 mA (or 1 / 10 V).
The value range is depending on the selected measuring function (Func) and range (rAnG).
7.12 'Unit' with Temp-arrow: Temperature unit
Temperature unit: All referring settings and displays are done in this unit.
Choice between °C and °F (ex works: °C)
7.13 'OFFS' with Temp-arrow: Offset of temperature measuring
The offset of the measuring will be shifted by this value, the input is in °C. Calculation: see below.
Max. input range: -5.0...5.0 °C or 'oFF' (= 0.0°) (factory setting = off)
7.14 'SCAL' with Temp-arrow: Scale correction of temperature measuring
The scale of the measuring is changed by this value. Calculation: see below.
Max. input range: -5.00...5.00 or 'oFF' (= 0.00) (factory setting = off)
The adjusting of the temperature by means of offset and scale is intended to be used to compensate devia-
tions of the measuring. It is recommended to keep the scale correction deactivated (“oFF”). The display val-
ue is given by following formula:
Temperature display = measured value - offset
With a scale correction (just for calibration laboratories, etc) the formula changes:
Temperature display = (meas. value - offset) * ( 1 + scale correction/100)
After pressing key 1 again, the instrument will restart (display 8888).

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 10 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
8 Reshipment and Disposal
8.1 Reshipment
All devices returned to the manufacturer have to be free of any residual of measuring media
and other hazardous substances. Measuring residuals at housing or sensor may be a risk for
persons or environment
Use an adequate transport package for reshipment, especially for fully functional devices.
Please make sure that the device is protected in the package by enough packing materials.
8.2 Disposal instructions
Batteries must not be disposed in the regular domestic waste but at the designated collecting
points.
The device must not be disposed in the unsorted municipal waste! Send the device directly to
us (sufficiently stamped), if it should be disposed. We will dispose the device appropriate and
environmentally sound.
9 Calibration Services
Factory calibration certificate - DKD certificate - official certifications:
If the measuring instrument is supposed to receive a factory calibration certificate, it has to be sent to the
manufacturer. Just the manufacturer can check the factory settings and correct them if necessary.
10 Specification
Measuring range 1 (one of the following can be configured):
C.rnG = 0.01
Range (rAnG) r 4
Bereich (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 5000 µS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
0.00 –20.00 µS/cm
0.000 –2.000 µS/cm
Resistivity (rESi)
1 - 5000 Ohm·cm
0.00 -20.00 kOhm·cm
0 - 200 kOhm·cm
0 - 2000 kOhm·cm
TDS (tdS)
0.00 –20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
0.00 –20.00 mg/l
0.000 –2.000 mg/l
C.rnG = 0.1
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0.00 - 50.00 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
0.00 –20.00 µS/cm
Resistivity (rESi)
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00-20.00 kOhm·cm
0 - 200 kOhm·cm
0 - 2000 kOhm·cm
TDS (tdS)
0.0 –200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
0.00 –20.00 mg/l
C.rnG = 1
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 500 mS/cm
0.0 - 200.0 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
0.0 - 200.0 µS/cm
Resistivity (rESi)
1.00 - 50.00 Ohm·cm
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00 - 20.00 kOhm·cm
0 - 200 kOhm·cm
TDS (tdS)
0 - 1000 g/l
0.0 - 200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
0.0 - 200.0 mg/l
Salinity (SAL)
0.0 - 70.0
C.rnG = 10
Range (rAnG) r 4
Range (rAnG) r 3
Range (rAnG) r 2
Range (rAnG) r 1
Range (rAnG) r 0
Conductivity (cond)
0 - 5000 mS/cm
0 - 2000 mS/cm
0.0 - 200.0 mS/cm
0.00 - 20.00 mS/cm
0 - 2000 µS/cm
Resistivity (rESi)
0.10 - 5.000 Ohm·cm
1.00-50.00 Ohm·cm
1.0 - 500.0 Ohm·cm
1 - 5000 Ohm·cm
0.00-20.00 kOhm·cm
TDS (tdS)
0 - 2000 g/l
0.0 - 200.0 g/l
0.00 - 20.00 g/l
0 - 2000 mg/l
Meas. range 2 Temperature (only display) -5.0...140.0 °C (resolution 0.1°C or 0.1°F, NTC10k or Pt1000)
Attention: Consider application range of measuring cell
Accuracy: (at nominal temperature = 25°C)
Measuring: conductivity: ±0,5% of measured value ±0,3 FS (-RW: ±1% of m. value ±0,3 FS
Depending on measuring cell eventually worse
temperature: ±0.1°C of measured value ±1 Digit
Add. output signal: ±0.2 % FS
Temp. compensation: non linear function, linear function (coefficient configurable) or none

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 11 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
Min-/Max-Value Memory: Min and max measured values are stored
Output signal: refer to type plate, freely scaleable
Scaling: By entering display values for 4mA (or 0V) and 20mA (or 1V/10V) output
Connection: 4 - 20 mA type: 2-wire –output signal electrically isolated
options AV01 (0-1 V), AV10 (0-10 V): 3-wire –output signal electrically isolated
Auxiliary energy (supply voltage):Uv = 12 - 30 V DC (4-20 mA)
Uv = 12 - 30 V DC, max. 10mA (0-1V)
Uv = 18 - 30 V DC, max. 10 mA (0-10 V)
or refer to type plate
Rev. voltage protection: 50 V permanent
Perm. impedance (at 4-20mA): RA(Ohm) < ( (Uv –12 V) / 0.02 A )
Example: for Uv = 18V: RA < (18 V –12 V) / 0.02 A => RA < 300 Ohm
Permissible load (at 0-...V): RL(Ohm) > 3000 Ohm
Adjusting: via keys. Conductivity by editing cell constant K (CELL)
Temperature by offset and scale.
Display: approx. 10 mm high, 4-digit LCD-display
Ambient conditions for electronics:
Nominal temperature: 25°C
Operating condition: -25 to 50°C, 0 to 95 %RH (non-condensing)
Storage temperature: -25 to 70°C
Housing: ABS (IP65)
Dimensions: 82 x 80 x 55 mm (without elbow-type plug and sensor connector)
Mounting: With holes for wall mounting (in housing - accessible after cover has been removed).
Mounting distance: 50 x 70mm, max. shaft diameter of mounting screws is 4 mm.
Electrical connection: elbow-type plug conforming to DIN 43650 (IP65),
max. wire cross section: 1.5 mm², wire/cable diameter from 4.5 to 7 mm
EMC: In accordance with EN61326 +A1 +A2 (appendix A, class B), additional errors: < 1% FS.
When connecting long leads adequate measures against voltage surges have to be taken.
The electrode connections have to be protected sufficiently against ESD pulses, if the de-
vice is used in areas with risk of ESD.
11 Variants/ Measuring Cells and Accessories
Type/ Application
Best Value:
Laboratory grade cells
Standard cable length: 1 m
Option -PG (PG13.5
Thread), max. 6 bar @22°C
Standard cable length: 1 m
Professional, Fieldmounting
M12; G1/2A,
max. 16 bar @22°C
Standard cable length: 5 m
4 pole graphite cells,
Especially for operation
above 2000 µS/cm, “dirty
applications”, Sea water,
etc.
5 ranges
0.1µS/cm..500 mS/cm
Ø12mm 4-pole cell LFE-400
Graphite; C= 0.55, -5…+80 °C
Ø12mm 4-pole cell LFE-400-PG
Graphite; C= 0.55; -5…+80 °C
Ø16mm 4-pole-cell
LFE-430
Graphite, C= 0.4;
0-60°C (wider on
request)
2 pole graphite cells,
Suitable for Sweat/ Drinking
Water
Recommended range up to
2000 µS/cm
Ø12mm 2-pole cell LFE-202
Graphite; C=1.0; -5 … +80
Ø12mm 2-pole cell LFE-202-PG
Graphite; C= 1.0; -5 … +80°C
Ø16mm 2-pole cell
LFE-230
Graphite; C=0.9;
0-60°C (wider on
request)
Purewater measuring cells

T46.0.21.6C-02 Operating Manual GLMU 400 MP_UNI (without measuring cell) page 12 of 10
GHM GROUP –Greisinger | GHM Messtechnik GmbH
Hans-Sachs-Str. 26 | 93128 Regenstauf | GERMANY
Phone [phone] | Fax [phone]
www.greisinger.de |[e-mail]
Recommended range up to
200 µS/cm
Ø12mm 2-pole cell LFE-240-RW
Stainless steel/PEEK; C= 0.1
; -5 … +80°C
Ø12mm 2-pole cell
LFE-220
Stainless
steel/PEEK; C= 0.1;
-10…+100 °C
2pole glass/platinum cell,
suitable for organic liquids
(like alcohol, gasoline ,
diesel etc.)
Recommended range up to
1000 µS/cm
Ø12mm 2-pole cell LFE-210
Glass/Platinum; C=1.0
-
Accessories
PG13.5 Plug
on thread
adapter for
pressure less
use ,for Ø12mm shafts
GWA1Z G1A
Thread adapter:
from PG13,5 to G1”,
plastic, max. 6bar
-
GKL100: Conductivity control solution (100ml bottle, 1413 µS/cm)
GKL101: Conductivity control solution (250ml bottle, 84 µS/cm)
GKL102: Conductivity control solution (250ml bottle, 50 mS/cm)