GREISINGER GMH 5450 User manual

H83.0.01.6C-06
GHM Messtechnik GmbH - Standort Greisinger
D-93128 Regenstauf, Hans-Sachs-Straße 26
+49 (0) 9402 / 9383-0 +49 (0) 9402 / 9383-33 [email protected]
as of version 1.9 GMH 5450
WEEE-Reg.-Nr. DE 93889386
Operating manual
Conductivity measuring device
water-proof, with data logger

Please carefully read these instructions before use!

Please consider the safety instructions!

Please keep for future reference!

H83.0.01.6C-6 Operating manual GMH 5450 page 2 of 20
_____________________________________________________ _____________________________________________________________________________
Index
1GENERAL NOTE......................................................................................................................................................3
2SAFETY......................................................................................................................................................................3
2.1 INTENDED USE.......................................................................................................................................................3
2.2 SAFETY SIGNS AND SYMBOLS................................................................................................................................3
2.3 SAFETY GUIDELINES..............................................................................................................................................3
3PRODUCT SPECIFICATION..................................................................................................................................4
3.1 SCOPE OF SUPPLY ..................................................................................................................................................4
3.2 OPERATION AND MAINTENANCE ADVICE..............................................................................................................4
4HANDLING................................................................................................................................................................5
4.1 DISPLAY ELEMENTS...............................................................................................................................................5
4.2 PUSHBUTTONS.......................................................................................................................................................5
4.3 CONNECTIONS .......................................................................................................................................................6
4.4 POP-UP CLIP...........................................................................................................................................................6
5START OPERATION................................................................................................................................................7
6PRINCIPLES OF THE MEASUREMENTS...........................................................................................................7
6.1 BASICS ABOUT CONDUCTIVITY .............................................................................................................................7
6.2 MEASURING RANGES AND CELL CONSTANTS........................................................................................................7
6.3 CONDUCTIVITY MEASUREMENT............................................................................................................................7
6.4 RESISTIVITY MEASUREMENT.................................................................................................................................8
6.5 TDS MEASUREMENT..............................................................................................................................................8
6.6 SALINITY MEASUREMENT......................................................................................................................................8
6.7 ELECTRODES /MEASURING CELLS.........................................................................................................................9
6.7.1 Assignment bayonet-connector......................................................................................................................9
6.7.2 Design and selection......................................................................................................................................9
6.8 TEMPERATURE COMPENSATION ............................................................................................................................9
6.8.1 Temperature compensation “nLF” according to EN 27888 .........................................................................9
6.8.2 Linear temperature compensation and determination of temperature coefficient “t.Lin“ ............................9
7CONFIGURATION.................................................................................................................................................10
8DATA LOGGER......................................................................................................................................................13
8.1 MANUAL RECORDING (“FUNC-STOR”)................................................................................................................13
8.2 AUTOMATIC RECORDING WITH SELECTABLE CYCLE TIME “FUNC CYCL” .........................................................14
9UNIVERSAL OUTPUT...........................................................................................................................................15
9.1 INTERFACE...........................................................................................................................................................15
9.2 ANALOG OUTPUT.................................................................................................................................................15
10 ADJUSTMENT OF TEMPERATURE INPUT.................................................................................................16
11 AUTOMATIC ADJUSTMENT/CALIBRATION OF CELL CONSTANT ...................................................16
12 GLP........................................................................................................................................................................17
12.1 CALIBRATION INTERVAL (C.INT).....................................................................................................................17
12.2 CALIBRATION STORAGE (READ CAL).............................................................................................................17
13 ALARM (“AL.”) ...................................................................................................................................................18
14 REAL TIME CLOCK (“CLOC”).......................................................................................................................18
15 ACCURACY CHECK / ADJUSTMENT SERVICE ........................................................................................18
16 REPLACING BATTERIES.................................................................................................................................18
17 ERROR AND SYSTEM MESSAGES................................................................................................................19
18 RESHIPMENT AND DISPOSAL.......................................................................................................................19
18.1 RESHIPMENT ....................................................................................................................................................19
18.2 DISPOSAL INSTRUCTIONS.................................................................................................................................20
19 SPECIFICATION.................................................................................................................................................20

H83.0.01.6C-6 Operating manual GMH 5450 page 3 of 20
_____________________________________________________ _____________________________________________________________________________
1 General Note
Read this document carefully and get used to the operation of the device before you use it. Keep this
document within easy reach near the device for consulting in case of doubt.
Mounting, start-up, operating, maintenance and removing from operation must be done by qualified, specially
trained staff that have carefully read and understood this manual before starting any work.
The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended
one, ignoring this manual, operating by unqualified staff as well as unauthorized modifications to the device.
The manufacturer is not liable for any costs or damages incurred at the user or third parties because of the
usage or application of this device, in particular in case of improper use of the device, misuse or malfunction
of the connection or of the device.
The manufacturer is not liable for misprints.
2 Safety
2.1 Intended Use
The device is designed for measuring conductivity, resistivity, salinity and TDS –using external suitable
electrodes (measuring cells). The electrodes are connected via 7-pole bayonet connection.
Please consider: Depending on the measuring range different electrode types may be needed –choose an
appropriate one.
There is the possibility to connect a temperature sensor (Pt1000 or NTC 10k) to the 7-pole bayonet socket.
Generally a suitable temperature sensor is included to the electrode. The measured temperature is used for
the automatic temperature compensation (e.g. Lin or nlF) and is additionally displayed.
The safety requirements (see below) have to be observed.
The device must be used only according to its intended purpose and under suitable conditions.
Use the device carefully and according to its technical data (do not throw it, strike it, etc.)
Protect the device from dirt.
2.2 Safety signs and symbols
Warnings are labeled in this document with the followings signs:
Caution! This symbol warns of imminent danger, death, serious injuries
and significant damage to property at non-observance.

Attention! This symbol warns of possible dangers or dangerous
situations which can provoke damage to the device or environment at
non-observance.
Note! This symbol point out processes which can indirectly influence
operation or provoke unforeseen reactions at non-observance.
2.3 Safety guidelines
This device has been designed and tested in accordance with the safety regulations for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures
and special safety advises given in this manual will be adhered to when using the device.
1. Trouble-free operation and reliability of the device can only be guaranteed if the device is not subjected to
any other climatic conditions than those stated under "Specification".
If the device is transported from a cold to a warm environment condensation may cause in a failure of the
function. In such a case make sure the device temperature has adjusted to the ambient temperature
before trying a new start-up.

H83.0.01.6C-6 Operating manual GMH 5450 page 4 of 20
_____________________________________________________ _____________________________________________________________________________

2. If there is a risk whatsoever involved in running it, the device has to be switched off
immediately and to be marked accordingly to avoid re-starting.
Operator safety may be a risk if:
- there is visible damage to the device
- the device is not working as specified
- the device has been stored under unsuitable conditions for a longer time.
In case of doubt, please return device to manufacturer for repair or maintenance.
3. When connecting the device to other devices the connection has to be designed most thoroughly as
internal connections in third-party devices (e.g. connection GND with protective earth) may lead to
undesired voltage potentials that can lead to malfunctions or destroying of the GMH 5155 and the
connected devices.
This device must not be run with a defective or damaged power supply unit.
Danger to life due to electrical shock!
4. Do not use these products as safety or emergency stop devices or in any other application
where failure of the product could result in personal injury or material damage.
Failure to comply with these instructions could result in death or serious injury and material
damage.
5. This device must not be used at potentially explosive areas! The usage of this device at
potentially explosive areas increases danger of deflagration, explosion or fire due to
sparking.
3 Product Specification
3.1 Scope of supply
The scope of supply includes:
GMH 5450 with 2 AAA batteries
Operating manual
Short form manual
3.2 Operation and maintenance advice
1. Battery operation:
If ‘bAt’ is shown in the lower display the battery has been used up and needs to be replaced. However,
the device will operate correctly for a certain time. If ‘bAt’ is shown in the upper display the voltage is too
low to operate the device; the battery has been completely used up. Battery change: p.r.t. chapter Fehler!
erweisquelle konnte nicht gefunden werden..
The battery has to be taken out, when storing device above 50°C. We recommend taking out
battery if device is not used for a longer period of time.
After recommissioning the real-time clock has to be set again.
2. Treat device and sensor carefully. Use only in accordance with above specification. (do not throw, hit
against etc.). Protect plug and socket from soiling.
3. USB or mains operation:
When connecting a mains cable or USB interface cable, please take care to connect only allowed
components.
The output voltage of a connected power supply unit has to be between 4.5 and 5.5 V DC.
Don’t apply overvoltage!
We recommend operation with interface cable USB 5100. Then device is supplied by the USB interface of
the connected PC or USB power supply adapter.

H83.0.01.6C-6 Operating manual GMH 5450 page 5 of 20
_____________________________________________________ _____________________________________________________________________________
4 Handling
4.1 Display elements
1
Main display: conductivity (mS/cm, µS/cm)
resistivity (kΩcm, MΩcm)
TDS / total dissolved solids (mg/l)
salinity (SAL)
2
Secondary display: measuring value temperature
3
Arrows to selected measuring unit
4
Rating of battery state
5
Display elements to show minimum / maximum / memorized
measuring value
6
nLF, NaCl, Lin:display element for selected temperature
compensation
7
%/K, 1/cm: additional configuration units
8
logg-arrow: logger is ready
arrow flashing: automatic recording (Logg CYCL) is active
4.2 Pushbuttons
On / off key, backlight
press shortly: activate backlight or switch on instrument
press longer: switch off instrument
set / menu:
press shortly: manual temperature input (if no
temperature probe is connected)
press for 2 sec. (menu): invoke configuration menu
min / max:
press shortly: min. or max. value is displayed
press for 2 sec: the corresponding value is deleted
cal: only at mode ‘cond’=conductivity:
press for 2 sec: start cell constant adjustment
store / enter:
Logger off: hold and save current measuring value
(‘HLD’ is displayed)
Logger on: Operation of data logger –chapter 8
Set/Menu: confirm settings, return to measuring

H83.0.01.6C-6 Operating manual GMH 5450 page 6 of 20
_____________________________________________________ _____________________________________________________________________________
4.3 Connections
Universal output: interface, supply, analog output
(see chapter 9 “Universal Output”)
7-pole bayonet socket: connection for electrode /
measuring cell and temperature probe
4.4 Pop-up clip
Handling:
•Pull at label “open” in order to swing open the pop-up clip.
•Pull at label “open” again to swing open the pop-up clip further.
Pop-up clip closed
Pop-up clip at position 90°
Pop-up clip at position 180°
Function:
• The device with a closed pop-up clip can be plainly laid onto a table or attached to a belt, etc.
• The device with pop-up clip at position 90° can be set up on a table, etc.
• The device with pop-up clip at position 180° can be suspended from a screw or the magnetic holder
GMH 1300.
Device attached to a belt
Device set up on a table
Device suspended from
magnetic holder
GMH 1300

H83.0.01.6C-6 Operating manual GMH 5450 page 7 of 20
_____________________________________________________ _____________________________________________________________________________
5 Start Operation
Connect electrodes, turn device on via key.
After segment test the device displays some information on its configuration:
if zero point or slope correction is active
(see chapter 10 Adjustment of temperature input)
If a measuring cell will be connected to the instrument the first time or if the measuring cell was changed, the
referring cell parameters in the instrument have to be entered, before measuring:
,und . Please refer to chapter Fehler! Verweisquelle konnte nicht gefunden
werden. Configuration
After that the device is ready for measuring.
6 Principles of the measurements
6.1 Basics about conductivity
Definition of conductivity : The ability of a material to conduct electric current:
l: length of the material
A: diameter
R: measured resistance
Unit , common for liquids: and
The conductivity is the reciprocal value of the resistivity.
(The conductance is the reciprocal value of the measured resistance R)
6.2 Measuring ranges and cell constants
Different measuring ranges can be realized depending on the used electrode. Therefore the device offers
four cell constant ranges to choose, depending on the correspondent cell constant K:
CELL rAnG
Selectable cell constant K
Application
0.01
0.004000 - 0.015000•1/cm
Ultra-pure water, electrodes with K = 0.01
0.1
0.04000 - 0.15000•1/cm
Ultra-pure water, electrodes with K = 0.1
1
0.4000 - 1.5000•1/cm
Standard electrodes e.g. with K= 0.55 or K=1
10
4.000 - 15.000 •1/cm
Electrodes with K=10 (for extremely high conductivities)
The cell constant can be selected manually in the configuration menu (see chapter 7 “Configuration”) or with
the adjustment/calibration function. Then there are two possibilities:
- automatically with an reference solution (temperature compensated)
- adjustment/calibration of the displayed value if actual value of solution is known
6.3 Conductivity measurement
The conductivity measurement is a rather uncomplicated measurement. The standard electrodes are stable
for a long time if used correctly and can be adjusted by an integrated Cal-function.
Attention: The device covers a wide measuring range, however a electrode suitable for the
measuring range has to be used.
Range
CELL
- rAnG
1
2
3
4
5
0.01
0.000 - 5.000 µS/cm
0.00 - 50.00 µS/cm
0.0 - 500.0 µS/cm
0 - 5000 µS/cm
0.00 - 50.00 mS/cm
0.1
0.00 - 50.00 µS/cm
0.0 - 500.0 µS/cm
0 - 5000 µS/cm
0.00 .. 50.00 mS/cm
0.0 - 500.0 mS/cm
1
0.0 - 500.0 µS/cm
0 - 5000 µS/cm
0.00 - 50.00 mS/cm
0.0 –500.0 mS/cm
0 - 1000 mS/cm
10
0 - 5000 µS/cm
0.00 - 50.00 mS/cm
0.0 - 500.0 mS/cm
0 –1000 mS/cm
---
If the range selection is set to „Auto Range“, the range with the best resolution is automatically selected.
However, logger or interface operation requires a manual/fixed selection of the measuring range from the
table above (No logger/interface operation with Auto-range!).


H83.0.01.6C-6 Operating manual GMH 5450 page 8 of 20
_____________________________________________________ _____________________________________________________________________________
6.4 Resistivity measurement
The resistivity is the reciprocal value of the conductivity and the device displays it in kOhm•cm (MOhm•cm).
Range
CELL
- rAnG
1
2
3
4
0.01
0.10 - 50.00 kOhm•cm
0.1 - 500.0 kOhm•cm
0.000 - 5.000 MOhm•cm
0.000 - 50.00 MOhm•cm
0.1
0.010 - 5.000 kOhm•cm
0.01 - 50.00 kOhm•cm
0.0 - 500.0 kOhm•cm
0.000 - 5.000 MOhm•cm
1
0.0010 - 0.5000 kOhm•cm
0.001 - 5.000 kOhm•cm
0.00 - 50.00 kOhm•cm
0.0 - 500.0 kOhm•cm
10
---
0.0001 - 0.5000 kOhm•cm
0.000 - 5.000 kOhm•cm
0.00 - 50.00 kOhm•cm
If the range selection is set to „Auto Range“, the range with the best resolution is automatically selected.
However, logger or interface operation requires a manual/fixed selection of the measuring range from the
table above (No logger/interface operation with Auto-range!).
6.5 TDS measurement
At the TDS (total dissolved solids) measurement the filtrate dry residue is determined by means of the
conductivity and a conversion factor (C.tdS). Well suited for easy concentration measurements of e.g. salt
solutions. The determined value is displayed in mg/l.
Range
CELL
- rAnG
1
2
3
4
0.01
0.000 - 5.000 mg/l
0.00 - 50.00 mg/l
0.0 - 500.0 mg/l
0 - 5000 mg/l
0.1
0.00 - 50.00 mg/l
0.0 - 500.0 mg/l
0 - 5000 mg/l
---
1
0.0 - 500.0 mg/l
0 - 5000 mg/l
---
---
10
0 - 5000 mg/l
---
---
---
Displayed value TDS = conductivity [in µs/cm, nLF-temp. comp. at 25°C] •C.tdS (input at menu)
Approximately:
C.tdS
0.50
Monovalent salts with 2 ion types (NaCl, KCl, etc.)
0.50
Natural waters / surface waters, drinking water
0.65 - 0,70
e.g. salt concentration of aqueous fertilizer solutions
Attention: This are only approximate values –good for estimations, but no precise measurement.
For precise measurements the conversion value has to be determined for the corresponding solution for the
relevant concentration range.
This may be done by comparison with known reference solutions or by actually evaporating a certain amount
of solution with determined conductivity and subsequent weighing of the dry residue.
6.6 Salinity measurement
At the salinity measurement “SAL” the salinity (salt content) of seawater is determined (based on:
International Oceanographic Tables; IOT). Standard seawater has a salinity of 35 ‰ (35 g salt per 1 kg
seawater).
Commonly the measured value is displayed dimensionless in ‰ (g/kg).
Additionally the term “PSU” (Practical Salinity Unit) is sometimes used, the displayed value is the same.
The salinity measurement has its “own” temperature compensation, i.e. the temperature is automatically
taken into account for the salinity measurement. The menu settings regarding the temperature compensation
are ignored.
Attention: The salt composition of the different seas is not the identical. Depending on place,
weather, tides, etc. there may be considerable divergences to the 35 ‰ according to IOT.
Additionally the salt composition may influence the ratio between salinity and actual salt content.
For many salts of the seawater aquaristics the corresponding tables are available (salt weight to salinity
according to IOT or conductivity). Considering these tables, very precise salinity measurements can be
performed (Therefore we recommend the 4-pole graphite measuring cells LF 400 or LF 425.).


H83.0.01.6C-6 Operating manual GMH 5450 page 9 of 20
_____________________________________________________ _____________________________________________________________________________
6.7 Electrodes / measuring cells
6.7.1 Assignment bayonet-connector
device pin assignment
1: electrode I+
2: electrode U+
3: electrode U-
4: electrode I-
5: temperature sensor
6: temperature sensor
7: not connected
6.7.2 Design and selection
Basically there are two types of measuring cells: 2-pole and 4-pole cells. The operation is done similarly; the
4-pole measuring cells can compensate polarization effects and –up to some degree –soiling due to its
complex measuring method.
2-pole measuring cell
4-pole measuring cell
The selection of a suitable electrode depends on the desired application.
The widest range of application is guaranteed by high-quality 4-pole graphite measuring cells
(LF 400 or LF 425, all the above applications and: seawaters, titration and sewage).
For low conductivities (<10 0µS/cm) stainless steel measuring cells offer advantages (LF 200 RW,
pure and ultrapure water, boiler water, osmosis, filter technology).
2-pole platinum electrodes with glass shaft are good solution for used in petrol, diesel, etc. with low
conductivities (< 1000 µS/cm) (LF 210)
6.8 Temperature compensation
The conductivity of aqueous solutions depends on its temperature. The temperature dependency is strongly
dependent on the type of solution. The temperature compensation recalculates solutions’ conductivity to a
consistent reference temperature. The most common reference temperature is 25 °C.
6.8.1 Temperature compensation “nLF” according to EN 27888
For most applications (e.g. in the area of fish farming, surface or drinking water measurements, etc.) the non-
linear temperature compensation for natural water (“nLF”, according to EN 27888) is sufficiently accurate.
The common reference temperature is 25 °C.
Recommended application range of nLF-compensation: between 60 µS/cm and 1000 µS/cm.
6.8.2 Linear temperature compensation and determination of temperature coefficient “t.Lin“
If the actual function needed for exact temperature compensation is not known, “linear temperature
compensation” is normally selected (Menu, t.Cor = Lin, t.Lin corresponds ), i.e. one assumes that the
actual temperature dependency at the considered concentration range is approximately equal:
Temperature coefficient of about 2.0 %/K are most common.
A temperature coefficient can be determined for example by measuring a solution with deactivated
temperature compensation at two different temperatures (T1 and T2).

H83.0.01.6C-6 Operating manual GMH 5450 page 10 of 20
_____________________________________________________ _____________________________________________________________________________
TKlin is the value input at the menu “t.Lin”.
LFT1 conductivity at temperature T1
LFT2 conductivity at temperature T2
7 Configuration
Some menu points depend on current device settings (e.g. some points are locked if logger
memory contains data sets).
To change device’s settings, press “menu” for 2 seconds. This will activate the configuration menu
(main display: “SEt”). Pressing “menu” changes between the menus points, pressing jumps to the
referring parameters, which can be selected with key .
The parameter value can be changed with or .
Pressing “menu” again jumps back to the main configuration menu and saves the settings.
Pressing “enter” finishes the configuration.
Pressing “menu” and “store” at the same time for more than 2 seconds will reset the
device to factory defaults.
If there are data sets stored and logger is set to “manual recording” (“Func Stor”) the first
menu point displayed is “rEAd Logg” (see chapter 8 “Data Logger”)
If no key is pressed for more than 2 minutes the configuration will be aborted. All changes will
be discarded!
Menu
Parameter
Value
Description
or
rEAd Logg: Read manual recordings,
see chapter 8.1 Manual recording (“Func-Stor”)
Set Configuration: General configuration
Input: Selection of measured variable
**
Cond
Conductivity
rES
Resistivity
SAL
Salinity
tdS
Total dissolved solids
TDS measurement: conversion factor (only if Inp = tdS)
0.40 - 1.00
Conversion factor for TDS measurement
Cell Range: Adjustment of cell constant: cell constant range
0.01
Ultrapure water, electrodes with K ~ 0.01
0.1
Ultrapure water, electrodes with K ~ 0.1
1
Standard electrodes, i.e. with K= 0.55 or K=1
10
Electrodes with K=10
Cell Factor: Adjustment of cell constant: multiplication factor
0.4000 -
1.5000
Multiplication factor of cell constant
Cell constant CELL = CELL Range * CELL Factor
t-Input: Selection of temperature input type
ntc
NTC 10k sensor
Pt
Pt1000 sensor
Range: Selection of display range (conductivity, resistivity or tdS)
Auto
Automatic range selection
e.g. 500.0 µS/cm
Example for CELL rAng 1 and InP Cond:
others in chapter 6.26.1
…
1000 mS/cm
Example for CELL rAng 1 and InP Cond: others in chapter 6.2
Automatic adjustment/calibration with reference solution (only if Inp = Cond)
Edit
Manual adjustment to reference value
REF.S
Choice of standard reference solutions

H83.0.01.6C-6 Operating manual GMH 5450 page 11 of 20
_____________________________________________________ _____________________________________________________________________________
REF.S: Choice of standard reference solutions for automatic adjustment/cal.
1413 µS/cm
Reference solution 0.01 M KCL
2760 µS/cm
0.02 M KCL
12.88 mS/cm
0.1 M KCL
50 mS/cm
Sea-water reference solution KCL
111.8 mS/cm
1 M KCL
Unit t: Selection of temperature unit
°C
All temperature values in degree Celsius
°F
All temperature values in degree Fahrenheit
Temperature compensation (not for InP = SAL)
oFF
No temperature compensation of conductivity measurement
nLF
Non-linear function for natural waters according to EN 27888
(ISO 7888), ground, surface and drinking water
NaCl
Compensation for weak NaCl-solutions (pure and ultrapure water)
Lin
Linear temperature compensation
Compensation coefficient (only if t.Cor = Lin)
0.300 3.000
Temperature compensation coefficient in %/K
Reference temperature of temperature compensation (only if t.Cor = Lin or nLF)
25 °C / 77 °F
Reference temperature 25 °C / 77 °F
20 °C / 68 °F
Reference temperature 20 °C / 68 °F
Adjustment/Calibration: Adjustment reminder period (factory setting: 180)
1 …730
Adjustment reminder period (in days)
oFF
No adjustment reminder
Auto Hold: Automatic measuring value identification (only if Logger = oFF)
on
Auto measuring value identification (only if Logger = oFF) Auto Hold
oFF
Standard hold function on keypress (only if Logger = oFF)
Auto Power-Off : Selection of power-off delay
1...120
Power-off delay in minutes.
Device will be automatically switched off as soon as this time has
elapsed if no key is pressed/no interface communication takes place.
oFF
Automatic power-off function deactivated (continuous operation)
Background illumination
oFF:
Illumination deactivated
5 … 120
Turn off illumination after 5… 120s (factory settings: 5 s)
on:
Illumination always on

H83.0.01.6C-6 Operating manual GMH 5450 page 12 of 20
_____________________________________________________ _____________________________________________________________________________
Menu
Parameter
Value
Description
or
Set Output: Configuration of universal output
oFF
Interface and analog output off -> minimal power consumption
SEr:
Serial interface activated
dAC:
Analog output activated
01,11..91
Base address for serial interface communication
0.0000 µS/cm
.. 1000 mS/cm
Measuring value that should correspond to output 0 V
e.g. for 0.0000 µS/cm
0.0000 µS/cm
.. 1000 mS/cm
Measuring value that should correspond to output 1 V
e.g. for 100.0 mS/cm
Set Corr: Measurement correction
**
Zero point adjustment / offset of temperature measurement
**
oFF
No zero point adjustment for temperature measurement
-5.0 … 5.0°C
Offset of temperature measurement in °C
Slope adjustment of temperature measurement
**
oFF
No slope adjustment for temperature measurement
-5.00 … 5.00
Slope correction of temperature measurement in [%]
Set Alarm: Configuration of alarm function
On / No.So
Measuring channel cond/rES/TDS/SAL: alarm on with buzzer / without
buzzer
OFF
No alarm function for measuring channel cond/rES/TDS/SAL
0.0000 µS/cm
.. 1000 mS/cm
Min-alarm limit for cond/rES/TDS/SAL (not if AL. 1. oFF)
0.0000 µS/cm
.. 1000 mS/cm
Max-alarm limit for cond/rES/TDS/SAL (not if AL. 1. oFF)
On / No.So
Temperature measurement: alarm on with buzzer / without buzzer
OFF
No alarm function for temperature measurement
-5.0 ..+100.0 °C
Min-alarm limit for temperature (not if AL. 2. oFF)
-5.0 ..+100.0 °C
Max-alarm limit for limit temperature (not if AL. 2. oFF)
Set Logger: Configuration of logger function
**
Selection of logger function
*
oFF
No logger activated
Stor
Store: Manual recording
CYCL
Cyclic: Cyclic logger
0:01... 60:00
Cycle time in [minutes:seconds] (for cyclic logger)
**
Set Clock: Einstellen der Echtzeituhr
HH:MM
Clock: set time hours:minutes
YYYY
Year: set year
TT.MM
Date: set date day.month
rEAd CAL: Read calibration data:
see chapter 12.2 “Calibration storage (rEAd CAL)”
(*) If logger memory contains data sets parameters marked with (*) cannot be called. You
have to clear memory to change these parameters!
(**) If logger is running parameters marked with (**) cannot be called.

H83.0.01.6C-6 Operating manual GMH 5450 page 13 of 20
_____________________________________________________ _____________________________________________________________________________
8 Data Logger
No logger operation possible with auto-range! The measuring range has to be selected
explicitly –see chapter 7 “Configuration”–
The device supports two different logger functions:
“Func-Stor”: Manual recording by keypress “store”
Additional input of measuring point (L-Id) is needed
“Func-CYCL”: Automatic recording at intervals of set cycle time
The logger stores 2 measuring values per data set.
One data set consists of: meas. value cond/rES/TDS/SAL (one of them)
meas. value temperature
measuring point L-Id (only for “Func-Stor”)
time and date (when data set is saved)
For the evaluation of the data the software GSOFT3050 (version V3.0 or higher) has to be used. The
software also allows easy configuration and starting of the logger.
When the logger is activated (Func Stor or Func CYCL) the hold function is no more available, the key
“store” is solely used for the operation of the logger functions.
8.1 Manual recording (“Func-Stor”)
a) Save measurements manually:
Up to 1000 measurements can be saved if logger function “Func store” is selected. (see “Configuration”):
Press “store” shortly:data set is saved (“St. XX” is displayed shortly,
where XX is the number of the data set)
Input of the measuring point “L-Id”: Selection of measuring point via keys or .
Number 0…19999 or text assigned to number 1…40
(comfortable assignment of texts can be done with gratis software GMHKonfig)
Confirm input with .
If logger storage is full, the following is displayed:
b) Read manual recordings:
Saved data sets can be viewed both with PC-software GSOFT3050 and directly on the device display.
Press “menu” for 2 seconds: is displayed
“rEAd LoGG”is only displayed if data sets have been already stored! Otherwise the
configuration menu is displayed:
Press shortly: Change between measuring values, measuring point and date+time
of the currently selected data set
or
Change between different data sets
Quit display of recordings
c) Clear manual recordings:
If data sets have been stored, they can be deleted with the “store” key:
Press “store” for 2 seconds: Call menu “Clear”
Select with: or .
Clear nothing (cancel)
Clear all data sets


H83.0.01.6C-6 Operating manual GMH 5450 page 14 of 20
_____________________________________________________ _____________________________________________________________________________
Clear the latest data set
Confirm selection and quit menu “Clear”
8.2 Automatic recording with selectable cycle time “Func CYCL”
If logger function “Func CYCL” is selected (see “Configuration”) the device will automatically record
measuring values at intervals of the set cycle time.
The logger’s cycle time can be set from 1s to 60min (see “Configuration”).
Up to 10000 measurements can be saved if logger function “Func CYCL” is selected.
a) Start recording:
Press “store” for 2 seconds:Start menu, press again: automatic recording is started
Each storage process is signaled by shortly displaying “St.XXXXX”, where XXXXX is the number of the
saved data set.
If the logger memory is full, the recording stops automatically and the display shows .
b) Stop recording:
Press “store” for 2 seconds:If recording is running the “stop” menu is displayed
Select with or .
Do not stop recording (cancel)
Stop recording
If recording is running the “stop” menu is displayed
If you try to switch off the device while cyclic recording is active you will be asked
whether the recording should really be stopped.
The device can only be switched off if the recording is stopped. Auto-off function is
deactivated as long as cyclic recording is active.
c) Clear recordings:
Press “store” for 2 seconds:
If there are data sets stored and recording is already stopped the menu “Clear” is displayed
Select with or .
Clear nothing (cancel)
Clear all data sets
Clear latest data set
Confirm selection and quit menu “Clear”

H83.0.01.6C-6 Operating manual GMH 5450 page 15 of 20
_____________________________________________________ _____________________________________________________________________________
9 Universal Output
The output can be used either as serial interface (for USB 5100 interface converter) or as analog output
(0-1V). If the output is not needed, it is strongly recommended to deactivate it (Out oFF) to lower power
consumption. This increases battery life time.
If the device is used together with interface adapter USB 5100 the device is supplied from the interface.
device pin assignment:
1: external supply +5V, 50mA
2: GND
3: TxD/RxD (3.3V Logic)
4: +UDAC, analog output

Only suitable adaptor cables are
permitted (accessories)!
9.1 Interface
The following standard software packages are available:
GSOFT3050: Operating and evaluation software for the integrated logger function
EBS20M / -60M: 20-/60-channel software for measuring value display
GMHKonfig: Configuration Software (for free on internet)
In case you want to develop your own software we offer a GMH3000-development package including:
a universally applicable Windows functions library ('GMH3x32e.DLL') with documentation, can be used
by all ‘established’ programming languages, suitable for:
Windows XP™, Windows Vista™, Windows 7™, Windows 8™
Programming examples Visual Basic™, Delphi 1.0™, Testpoint™ etc.
The device has 2 channels:
- Channel 1: current measuring value (Cond, rES, TDS or SAL) and base
address
- channel 2: temperature value
The measuring-/ alarm- and display range values read back from the interface are
always in the selected measurement unit!
Attention: The auto-range-function should be turned off if interface
is used.
9.2 Analog output
An analog voltage 0-1V can be tapped at the universal output socket (mode: “Out dAC”).
The analog output can be easily scaled with DAC.0 and DAC.1.
Please take care not to load the analog output too heavily, otherwise the output value will be distorted and
the power consumption will rise. Loads up to approx. 10 kOhm are unproblematic.
If the displayed value goes beyond DAC.1 the output voltage will be 1V.
If the displayed value falls below DAC.0 the output voltage will be 0V.
In error case (Err.1, Err.2, ----, etc.) the output voltage will be slightly higher than 1V.


H83.0.01.6C-6 Operating manual GMH 5450 page 16 of 20
_____________________________________________________ _____________________________________________________________________________
10 Adjustment of temperature input
The temperature input can be adjusted with offset and scale. A reasonable adjustment presumes reliable
references (e.g. ice water, controlled precision water bath, etc.).
If the inputs are adjusted (i.e. offset and scale are different from default settings) the device will shortly
display “Corr” after turned on.
Default setting for offset and scale are ‘off’ = 0.0, i.e. inputs are not changed.
Zero point correction: Displayed value = measured value –OFFS
Zero point and slope correction: Displayed value = (measured value –OFFS) * (1 + SCAL / 100)
Displayed value °F = (meas. value °F - 32°F - OFFS) •(1 + SCAL / 100)
11 Automatic adjustment/calibration of cell constant
Besides the direct input of the cell constant (see below) via the menu (“CELL FACt”) the cell constant can
also be determined automatically (Please select CELL rAnG in menu before):
Manual adjustment or Adjustment with reference solution
Menu selection: “CAL Edit”“CAL rEF.S”
Menu selection of desired solution
1413 µS/cm 0.01 M KCL
2.76 mS/cm 0.02 M KCL
12.88 mS/cm 0.1 M KCL
50 mS/cm KCL
111.8 mS/cm 1 M KCL
Values for 25°C, the temperature
dependency of those solutions are known
by the device and are compensated
automatically.
Press Cal-key for 2 s,
start of calibration “actual value” e.g. “1823 µS/cm”“value of solution” e.g. “1413µS/cm”
and CAL with rotary symbol and CAL with rotary symbol
Calibration
Select desired display value wait until device measures stable value
with buttons “up” and “down”
and confirm with “enter”
Afterwards the device returns to the normal measuring operation mode or –if so –displays an error
message.
The resulting cell constant can be seen in the menu at “CELL rAng” and the calibration history.
Error messages of automatic adjustment/calibration:
CAL Err.1
Cell constant too high
Determined cell constant must not exceed 1.5 * cell range
CAL Err.2
Cell constant too small
Determined cell constant must not fall below 0.4 * cell range
CAL Err.3
Solution of wrong range
Wrong cell range / wrong solution / far beyond tolerance
CAL Err.4
Wrong temperature
Beyond permitted temperature:
0.0 –34.0 °C (or 0.0 –27.0 °C at 111.8 mS/cm)
Alternative to automatic adjustment:
Manual calculation of cell constant with a reference solution
Example KCl-solution c= 0.01 M: 1413 μS cm-1 at 25°C
At other temperatures switch temperature compensation off (t.Cor = oFF) and use the referring conductivity!
Conductivitydisplayed = 1900 μS cm-1 if selected cell constant is 1.000 cm-1 (CELL FACt = 1.000)
Conductivity of solution at solution temperature 25 °C: Conductivityreal = 1413 μS cm-1
Cell constant k = conductivityreal / conductivitydisplayed [cm-1]
= 1413 / 1970 * cm-1 = 0.7437 cm-1 (Enter CELL FACt of 0.7437)

H83.0.01.6C-6 Operating manual GMH 5450 page 17 of 20
_____________________________________________________ _____________________________________________________________________________
12 GLP
GLP (Good Laboratory Practice) includes regular check of devices and accessories. For pH measurements it
is highly important to ensure correct pH calibration. The device provides the following functions to help with
this.
GLP (Good Laboratory Practice) includes regular check of devices and accessories. For pH measurements it
is highly important to ensure correct pH calibration. The device provides the following functions to help with
this.
12.1 Calibration interval (C.Int)
You can input the interval after which the device reminds you to recalibrate.
The interval times should be chosen according to the application and the stability of the electrode. “CAL”
flashes on the display as soon as the interval has expired.
12.2 Calibration storage (rEAd CAL)
The last 16 calibrations are stored with results and date and can be read out.
Display calibration data:
Historical calibration data can be comfortably read out via PC software GMHKonfig and GSOFT3050 or
displayed directly at the device:
Press for 2 seconds:
The display will show:
or (configuration level)
Press several times until this is
displayed:
read cal. = “read calibration data”
Press shortly: switch between:
- CELL = cell constant
- C.rEF = reference value, at which cell constant has been adjusted
- Display of date+time of data set
or
Change between the different calibration data sets
Quit calibration data set display

H83.0.01.6C-6 Operating manual GMH 5450 page 18 of 20
_____________________________________________________ _____________________________________________________________________________
13 Alarm (“AL.”)
There are 3 possible settings:
off (AL.oFF), on with buzzer (AL.on), on without buzzer (AL.no.So).
Alarm is given in the following cases (if alarm active, AL.on or AL.no.So):
-Lower alarm boundary (AL. Lo) under-run
-Upper alarm boundary (AL. Hi) over-rum
-Sensor error
-Low battery (bAt)
-Err.7: system error (always with buzzer!)
In case of an alarm (and when polling the interface) the ‘PRIO’-flag is set in the returned interface message.
14 Real Time Clock (“CLOC”)
The real time clock is used for chronological assignment of the logger data and calibration points. Please
check the settings when necessary.
15 Accuracy Check / Adjustment Service
You can send the device to the manufacturer for adjustment and inspection.
Calibration certificate - DKD certificate - official certifications:
If the measuring instrument is supposed to receive a calibration certificate, it has to be sent to the
manufacturer (declare test points).
If the device is certificated together with a suitable sensor very high overall accuracies are possible.
Basic settings can only be checked and –if necessary –corrected by the manufacturer.
A calibration protocol is enclosed to the device ex works. This documents the precision reached by the
production process.
16 Replacing Batteries
Before changing batteries, please read the following instruction and
follow it step by step.
Not following the instruction may cause harm to the instrument or the
protection against ingress of water and dust may be lost!
Avoid unnecessary opening of the instrument!
1. Open the 3 Phillips screws at the backside of the instrument.
2. Lay down the still closed instrument, so that the display side
points upwards.
The lower half of the housing incl. the electronics should be kept
lying down during battery change.
This avoids loss of the 3 sealing rings placed in the screw holes.
3. Lift off upper half of housing. Keep an eye on the six function
keys, to be sure not to damage them.
4. Change carefully the two batteries (Type: AAA).
5. Check: Are the 3 sealing rings placed in the housing?
Is the circumference seal of the upper half sound and clean?
6. Close the housing, taking care that it is positioned correctly,
otherwise the sealing may be damaged. Afterwards press the
two halves together, lay the instrument with display pointing
downwards and screw it together again
Take care to screw only until you feel increasing resistance,
higher screwing force does not result in higher water protection!

H83.0.01.6C-6 Operating manual GMH 5450 page 19 of 20
_____________________________________________________ _____________________________________________________________________________
17 Error and System Messages
Error messages for measurement
Description
What to do?
No display or
confused
characters,
Device does not
react on keypress
Battery empty
Replace battery
Mains operation: wrong voltage or polarity
Check power supply, replace it if necessary
System error
Disconnect battery and power supply, wait shortly,
then reconnect
Device defective
Return to manufacturer for repair
Err.1
Measured value above allowable range
Check: pressure not within sensor range?
-> measuring value to high!
Sensor defective
Return to manufacturer for repair
Err.2
Measured value below allowable range
Check: pressure not within sensor range?
-> measuring value to low!
Sensor defective
Return to manufacturer for repair
Err.7
System error
Return to manufacturer for repair
Value extremely out of measuring range
Value extremely out of measuring range
----
Could not calculate display value
• measuring range or input range
exceeded
Check range parameter
• measured values are instable
Wait for signal regulation of the device
> CAL <
CAL flashing in
upper display
Either preset calibration interval has
expired or last calibration is not valid
Device has to be calibrated!
NO . AVTO
LO66 RAN6
Logger could not be started
Auto range for the display range is active
=> change the parameter in the configuration menu
Error messages for automatic cell constant adjustment/calibration:
CAL Err.1
Cell constant too high
Determined cell constant must not exceed
1.2* cell range
CAL Err.2
Cell constant too small
Determined cell constant must not fall below
0.4* cell range
CAL Err.3
Solution of wrong range
Wrong cell range / wrong solution / far
beyond tolerance
CAL Err.4
Wrong temperature
Beyond permitted temperature:
0.0 –34.0 °C (or 0.0 –27.0 °C at 111.8 mS/cm)
If “bAt” is flashing the battery will be exhausted soon. Further measurements are possible for short time. If
“bAt” is displayed continuously the battery is ultimately exhausted and has to be replaced. Further
measurements aren’t possible any more.
18 Reshipment and Disposal
18.1 Reshipment
All devices returned to the manufacturer have to be free of any residual of measuring media and
other hazardous substances. Measuring residuals at housing or sensor may be a risk for
persons or environment
Use an adequate transport package for reshipment, especially for fully functional devices.
Please make sure that the device is protected in the package by enough packing materials.

H83.0.01.6C-6 Operating manual GMH 5450 page 20 of 20
_____________________________________________________ _____________________________________________________________________________
18.2 Disposal instructions
Batteries must not be disposed in the regular domestic waste but at the designated collecting
points.
The device must not be disposed in the unsorted municipal waste! Send the device directly to us
(sufficiently stamped), if it should be disposed. We will dispose the device appropriate and
environmentally sound.
19 Specification
*) choice of electrode may limit the operational range, although a larger theoretical range is available from the
instrument’s side. Please refer to chapter 6.7
Measuring
ranges
count
5
Cell constant 0.4 … 1.5
Cell constant 0.04 … 0.15
Cell constant 0.004 … 0.015
Conductivity 1 *)
0.0 ... 500.0 µS/cm
0.00 ... 50.00 µS/cm
0.000 ... 5.000 µS/cm
” 2 *)
0 ... 5000 µS/cm
0.0 ... 500.0 µS/cm
0.00 ... 50.00 µS/cm
” 3 *)
0.00 ... 50.00 mS/cm
0 ... 5000 µS/cm
0.0 ... 500.0 µS/cm
” 4 *)
0.0 ... 500.0 mS/cm
0.00 ... 50.00 mS/cm
---
” 5 *)
0 ... 1000 mS/cm
---
---
Resistivity
0.0010 ... 500.0 kOhm*cm
0.010 ... 5000 kOhm*cm
0.0001 ... 50.00 MOhm*cm
TDS
0.0 ... 5000 mg/l
0.00 ... 5000 mg/l
0.000 ... 5000 mg/l
Salinity
0.0 ... 70.0 g/kg (PSU)
Temperature
-5.0 ... +100.0 °C, Pt1000 or NTC (10k)
23.0 ... 212.0 °F
Supported cell constants
4.000 …15.000 / cm; 0.4000 …1.5000 / cm; 0.04000 …0.15000 / cm;
0.004000 …0.015000 / cm
Accuracy
Conductivity
±0.5% of m.v. ±0.1 % FS (system accuracy is dependent on electrode!)
Temperature
±0.2 K
Connections
Conductivity,
Temperature
7-pole bayonet socket for connection of different measuring cells
Supported temperature sensors Pt1000 and NTC 10k
Interface / ext.
supply
4-pole bayonet socket for serial interface and supply (USB Adapter USB 5100)
Analog output 0-1V, adjustable
Display
4 ½ - digit, 7-segment, illuminated (white)
Add. functions
Min / max / hold function
Adjustment/
Calibration
Cell constant manually or automatically via selectable reference solution
GLP
Selectable adjustment intervals (1 to 730 days, CAL-warning after expiration)
Storage: latest 16 adjustments
Data logger
Real-time clock
Cyclic: 10000 data sets, cycle time selectable: 1s … 60 min
Single: 1000 data sets (with measuring point input, 40 selectable measuring point
texts or numbers)
Alarm
2 alarm channels with separate limit values for conductivity (or resistivity, TDS, SAL)
and temperature
Alerting: buzzer / visual / interface
Housing
Break-proof ABS housing, incl. silicone protective cover
Protection class
IP65 / IP67
Dimensions
L*W*H [mm]
160 * 86 * 37 incl. silicone protective cover,
approx. 250 g incl. battery and cover
Working conditions
-25 to 50 °C; 0 to 95 % RH (non condensing)
Storage temperature
-25 to 70 °C
Power supply
2*AAA battery (included in scope of supply) or external
Current
consumption
6.25 mA (for Out = oFF, equivalent to 160 h), backlight ~10mA (auto-off)
Battery indicator
4-stage battery state indicator,
Change battery display for exhausted battery: “bAt”, warning: “bAt” flashing
Auto-off function
Device will be automatically switched off if no key is pressed/no interface
communication takes place for the time of the power-off delay. The power-off delay
can be set to values between 1and 120 min.; it can be completely deactivated.
EMC
The device corresponds to the essential protection ratings established in the
Regulations of the Council for the Approximation of Legislation for the member
countries regarding electromagnetic compatibility (2004/108/EG)
Additional fault: <1%