Grizzly T10880 User manual

Model T10880 & T10881
G0442 & G0601 Cartridge Filter Replacement
with HEPA Filter Upgrade Kit
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step One:
Remove the filter L-braces from the blower housing, as shown above, by loosening and removing (6) 5/16” x
1” hex bolts, (12) 5/16” flat washers, and (6) 5/16” hex nuts. Remove and set the cartridge filter aside.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Two:
Remove the outlet port from the blower housing by loosening and removing (4) 5/16” x 1” hex bolts, (8) 5/16”
flat washers, and (4) 5/16” hex nuts.
!

!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Three:
Remove the mounting bracket that secures the intake barrel to the upper stand leg by loosening and removing (8)
5/16” x 1” hex bolts, (16) 5/16” flat washers, and (8) 5/16” nuts. Next, loosen and remove (8) 3/8” x 3/4” hex
bolts, (16) 3/8” flat washers, and (8) 3/8” nuts on the leg stand side. NOTE: Replace the mounting brackets with
the new types one at a time. DO NOT remove all old mounting brackets at once.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Four:
After each mounting bracket has been replaced with the new type, make sure to tighten all the bolts and nuts
securely before moving on to the next step.
!
!
!
!

!
!
!
!
!
!
!
!
!
!
!
!
!
Step Five:
Attach the rubber gasket to the outlet opening on the blower housing, then attach the outlet connector by
securing and fastening (10) 3/8” x 1” hex bolts, (20) 3/8” flat washers, and (10) 3/8” nuts.!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Six:
Assemble the HEPA leg stand, which consists of three segments: upper, middle and lower. Secure and fasten
using (8) 3/8” x 1” hex bolts, (16) 3/8” flat washers, and (8) 3/8” nuts. !
!
!
!
!
!

!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Seven:
Attach the HEPA leg stand to the outlet connector, as shown above, by securing and fastening (4) 3/8” x 1” hex
bolts, (8) 3/8” flat washers, and (4) 3/8” nuts. !
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Eight:
Attach the rubber gasket to the square top of the HEPA filter, as shown above. Take the filter adapter and attach
it to the square top of the HEPA filter with (16) 5/16” x 1” hex bolts and 5/16” flat washers. Tighten and secure
all bolts and nuts.
!
!
!
!

!
!
!
!
!
!
!
!
!
!
!
!
!
Step Nine:
Attach the rubber gasket to the outlet opening, then attach the filter adapter and HEPA filter to the blower
housing with (16) 3/8” x 1” hex bolts, (30) 3/8” flat washers, and (14) 3/8” nuts. Tighten and secure all bolts
and nuts.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Step Ten:
Fit the plastic canister collection bag over the bottom of the HEPA canister filter, and clamp in place with the
metal bag clamp, as shown above.
!
UPGRADE COMPLETE!