Groen NFPC series User manual

P IMPORTANTINFORMATION PKEEPFOROPERATOR PIMPORTANTINFORMATION P
OPERATOR MANUAL OM-NFPC
DOMESTIC
Part Number 121009
MODEL: NFPC
Braising Pan
Stainless Steel
Power Tilting
Electrically Heated
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.
WARNING
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.
.

OM-NFPC
2
IMPORTANT — READ FIRST — IMPORTANT
CAUTION: BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE
OPERATING INSTRUCTIONS, CAUTIONS, AND SAFETY INSTRUCTIONS
CONTAINED IN THIS MANUAL.
WARNING: THIS UNIT IS INTENDED FOR USE IN THE COMMERCIAL HEATING,
COOKING AND HOLDING OF WATER AND FOOD PRODUCTS, PER THE
INSTRUCTIONS CONTAINED IN THIS MANUAL. ANY OTHER USE COULD
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO THE
EQUIPMENT AND WILL VOID WARRANTY.
CAUTION: ELECTRICALLY GROUND THE PAN AT THE TERMINAL PROVIDED.
WARNING: THE BRAISING PAN MUST BE INSTALLED BY PERSONNEL WHO ARE
QUALIFIED TO WORK WITH ELECTRICITY. IMPROPER INSTALLATION
COULD RESULT IN PERSONAL INJURY OR EQUIPMENT DAMAGE.
CAUTION: STAND AWAY FROM THE HOT WATER WHILE TILTING THE PAN TO
EMPTY IT.
WARNING: DO NOT HEAT AN EMPTY PAN FOR MORE THAN FIVE MINUTES AT A
SETTING HIGHER THAN 300o F.
WARNING: AVOID ANY EXPOSURE TO THE STEAM ESCAPING FROM THE COVER
VENT. DIRECT CONTACT COULD RESULT IN SEVERE BURNS
WARNING: AVOID ALL DIRECT CONTACT WITH HOT EQUIPMENT SURFACES. DIRECT
SKIN CONTACT COULD RESULT IN SEVERE BURNS.
WARNING: AVOID ALL DIRECT CONTACT WITH HOT FOOD OR WATER IN THE
BRAISING PAN. DIRECT CONTACT COULD RESULT IN SEVERE BURNS.
WARNING: IF THE PAN CONTAINS ITEMS IN SAUCE OR MELTED FAT, THEY COULD
SLIDE FORWARD SUDDENLY DURING TILTING AND CAUSE THE HOT
LIQUID TO SPLASH OUT.
WARNING: USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY
GROEN OR ITS AUTHORIZED DISTRIBUTORS VOIDS ALL WARRANTIES
AND MAY CAUSE BODILY INJURY AND/OR EQUIPMENT DAMAGE.
SERVICE PERFORMED BY OTHER THAN FACTORY AUTHORIZED
PERSONNEL WILL VOID ALL WARRANTIES.
WARNING: ALWAYS TURN OFF ELECTRIC POWER BEFORE WORKING ON INTERNAL
COMPONENTS.
WARNING: BEFORE ANY CLEANING OPERATION, TURN THE THERMOSTAT TO “OFF”
TO CUT OFF POWER TO THE HEATING ELEMENTS. BEFORE CLEANING
ANY PART OTHER THAN THE INSIDE OF THE PAN DISCONNECT THE
ELECTRICAL SUPPLY AT THE CIRCUIT BREAKER OR FUSE BOX.
WARNING: BE CAREFUL TO AVOID CONTACT WITH THE CLEANER IN ACCORDANCE
WITH SUPPLIER AND MANUFACTURER RECOMMENDATIONS. MANY
CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS MEMBRANES
AND CLOTHING. READ THE WARNINGS AND FOLLOW DIRECTIONS ON
THE CLEANER LABEL.
CAUTION: NEVER LEAVE A CHLORINE SANITIZER IN CONTACT WITH STAINLESS
STEEL FOR LONGER THAN 30 MINUTES. LONGER CONTACT CAN CAUSE
CORROSION.
WARNING: DO NOT USE ANY FUSE WITH A HIGHER AMP RATING THAN THE RATING
SPECIFIED FOR THAT CIRCUIT.

OM-NFPC
3
Table of Contents
IMPORTANT OPERATOR WARNINGS .................................................. 3
REFERENCES ...................................................................... 3
EQUIPMENT DESCRIPTION .......................................................... 4
INSTALLATION ..................................................................... 5
INITIAL START-UP .................................................................. 6
OPERATION ....................................................................... 6
SEQUENCE OF OPERATION .......................................................... 8
CLEANING ......................................................................... 9
MAINTENANCE .................................................................... 10
TROUBLESHOOTING ............................................................... 11
PARTS LISTS ..................................................................... 12
DIAGRAMS & SCHEMATICS ......................................................... 13
MAINTENANCE LOG ................................................................ 22
WARRANTY ....................................................................... 23
References
ECONOMICS LABORATORY, INC.
St. Paul, Minnesota 55102
NATIONAL FIRE PROTECTION ASSOCIATION
60 Battery March Park
Quincy, Massachusetts 02269
NFPA/70 The National Electrical Code
NATIONAL SANITATION FOUNDATION
3475 Plymouth Rd.
Ann Arbor, Michigan 48106
UNDERWRITERS LABORATORIES, INC.
333 Pfingsten Rd.
Northbrook, Illinois 60062
ZEP MANUFACTURING
1390 Lunt Avenue
Elk Grove Village, Illinois 60007

OM-NFPC
4
Equipment Description
The Groen NFPC is a stainless steel, electrically
heated Braising Pan which is equipped with
integrated heating elements, a power tilting
mechanism, electrical controls and a hinged
cover. The Braising Pan serves as a braising
unit, griddle, fry pan, oven, kettle, bain-marie, or
food warmer and server. It can also be adapted
for use as a non-pressure steamer.
Construction of the pan body employs heavy-
duty stainless steel welded into a solid piece. It
has a polished interior and a semi-deluxe
exterior finish. A pouring lip is welded to the top
of the front wall. The cooking surface is a
stainless steel clad plate fitting with clamped-on
electrical heating elements. The elements are
positioned to ensure uniform heat transfer over
the entire surface. The pan is mounted on an
open-leg frame which is fabricated from tubular
stainless steel.
An electrically powered mechanism tilts the pan
forward. A three position switch on the front of
the control console gives the operator positive,
smooth-acting control of tilt.
Heating elements and other electrical
components are enclosed for safety. The
thermostat, heating indicator light, and tilting
switch are contained in a compact control
console which is mounted to the right of the pan
body.
The thermostat provides automatic control of
cooking temperature. Turning the thermostat
dial starts and stops heating and sets the pan
temperature. Only one electrical connection is
required to install the unit.
A vented, heavy gauge, one-piece, stainless
steel cover with a rear condensate drip shield on
the underside is standard on the Braising Pan. A
fully enclosed spring-type actuator counter
balances the cover to maintain either the opened
or closed position. The cover opens to the back.
It is hinged to the frame, so it moves
independently from the pan body.
The following models and options are available:
Model Pan Dimensions, Inches
Left to
Right Depth Front to Back
NFPC-3 31e7 or 9 25¼
NFPC-4 41e7 or 9 25¼
Optional Equipment (Either Model)
1. Fill faucet with swing spout and water hose
2. Model REJ Steamer Insert
3. Casters

OM-NFPC
5
Installation
Internal wiring for the Braising Pan is supplied
complete. When you receive it, the unit is ready
for connection. A wiring diagram is inside the
control box on the right side of the pan, as well
as in this manual (Pp 14-21). Your pan was
operated and tested at the factory to confirm that
all controls and heating elements were
functioning correctly.
Installation is as follows:
1. Set the unit in place and level it by turning
the adjustable feet. Make sure the tilting
mechanism has been rotated to its lowest
position and check levelness by placing a
spirit level on the bottom of the pan. The
unit must be level to avoid uneven cooking
across the pan.
2. At the electrical service entrance in the
bottom of the control box, make a
waterproof connection with the incoming
power line. A BX connection is not
recommended.
CAUTION
ELECTRICALLY GROUND THE PAN AT THE
TERMINAL PROVIDED.
3. Provide the proper electrical supply as
specified on the electrical plate attached to
the equipment. Observe local codes
and/or the National Electrical Code in
accordance with ANSI/NFPA 70 — latest
edition.
WARNING
THE BRAISING PAN MUST BE INSTALLED
BY PERSONNEL WHO ARE QUALIFIED TO
WORK WITH ELECTRICITY. IMPROPER
INSTALLATION COULD RESULT IN
PERSONAL INJURY OR EQUIPMENT
DAMAGE.
4. Any mechanical or electrical change must
be approved by the Groen Food Service
Engineering Department.
ELECTRICAL DATA*
Voltage Phase Power and Current Draw
NFPC-3 NFPC-4
208 1 11.4 KW - 54.8 AMP 14.25 KW - 68.5 AMP
208 3 11.4 KW - 31.6 AMP 14.25 KW - 39.6 AMP
240 1 12 KW - 50 AMP 15 KW - 62.5 AMP
240 3 12 KW - 28.9 AMP 15 KW - 36.1 AMP
380 3 12 KW - 18.2 AMP 15 KW - 22.8 AMP
480 1 12 KW - 25 AMP 15 KW - 31.25 AMP
480 3 12 KW - 14.5 AMP 15 KW - 18 AMP
Power tile motor draws 6 AMP at 120 Volts, Single Phase
*All data at 60 Hz.