Groen OM-BTD User manual

This manual provides information for:
OPERATOR MANUAL
IMPORTANT INFORMATION, KEEP FOR OPERATOR
PART NUMBER 121066, REV. D (04/11)
MODELS TD/FPC Domestic
BRAISING PAN
· Stainless Steel
· Table Top Mounted
· Manual Tilting
· Electrically Heated
· 40 Quart Capacity
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors
and liquids in the vicinity of this or any other appliance.
POST IN A PROMINENT LOCATION
Instructions to be followed in the event user smells
gas. This information shall be obtained by consulting
your local gas supplier. As a minimum, turn off the gas
and call your gas company and your authorized service
agent. Evacuate all personnel from the area.
WARNING
Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or
death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this
equipment.
NOTIFY CARRIER OF DAMAGE AT ONCE
It is the responsibility of the consignee to inspect the container upon receipt of
same and to determine the possibility of any damage, including concealed dam-
age. Unified Brands suggests that if you are suspicious of damage to make a
notation on the delivery receipt. It will be the responsibility of the consignee to file
a claim with the carrier. We recommend that you do so at once.
Manufacture Service/Questions 888-994-7636.
Information contained in this document is known to be current and accurate at the time
of printing/creation. Unified Brands recommends referencing our product line websites,
unifiedbrands.net, for the most updated product information and specifications.
1055 Mendell Davis Drive
Jackson, MS 39272
888-994-7636, fax [phone]
unifiedbrands.net

2 OM-TD/FPC
IMPORTANT - READ FIRST - IMPORTANT
CAUTION: BE SURE OPERATORS READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS,
CAUTIONS, AND SAFETY INSTRUCTIONS IN THIS MANUAL.
WARNING: THIS UNIT IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND HOLDING OF
WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED IN THIS MANUAL. ANY OTHER
USE COULD RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT AND WILL VOID
WARRANTY.
WARNING: ELECTRICALLY GROUND THE PAN AT THE TERMINAL PROVIDED.
WARNING: THE BRAISING PAN MUST BE INSTALLED BY PERSONNEL WHO ARE QUALIFIED TO WORK WITH
ELECTRICITY. IMPROPER INSTALLATION COULD RESULT IN PERSONAL INJURY OR EQUIPMENT
DAMAGE.
CAUTION: STAND AWAY FROM HOT WATER OR FOOD PRODUCTS WHILE TILTING THE PAN
WARNING: WHEN TILTING BRAISING PAN FOR PRODUCT TRANSFER:
1) USE CONTAINER DEEP ENOUGH TO CONTAIN AND MINIMIZE SPLASHING.
2) PLACE CONTAINER ON STABLE, FLAT SURFACE, AS CLOSE TO PAN AS POSSIBLE.
3) STAND TO SIDE OF PAN WHILE POURING — NOT DIRECTLY IN POUR PATH OF HOT CONTENTS.
4) RETURN PAN BODY TO LEVEL POSITION AFTER CONTAINER IS FILLED OR TRANSFER IS
COMPLETE.
5) DO NOT OVER FILL CONTAINER. AVOID DIRECT SKIN CONTACT WITH HOT CONTAINER AND ITS
CONTENTS.
WARNING: DO NOT HEAT AN EMPTY PAN FOR MORE THAN FIVE MINUTES AT A SETTING HIGHER THAN 300°F.
WARNING: AVOID ANY EXPOSURE TO THE STEAM ESCAPING FROM THE COVER VENT. DIRECT CONTACT
COULD RESULT IN SEVERE BURNS
WARNING: AVOID ALL DIRECT CONTACT WITH HOT EQUIPMENT SURFACES. DIRECT SKIN CONTACT COULD
RESULT IN SEVERE BURNS.
WARNING: AVOID ALL DIRECT CONTACT WITH HOT FOOD OR WATER IN THE BRAISING PAN. DIRECT CONTACT
COULD RESULT IN SEVERE BURNS.
WARNING: IF THE PAN CONTAINS ITEMS IN SAUCE OR MELTED FAT, THEY COULD SLIDE FORWARD SUDDENLY
DURING TILTING AND CAUSE HOT LIQUID TO SPLASH OUT.
WARNING: USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY THE MANUFACTURER OR
ITS AUTHORIZED DISTRIBUTORS VOIDS ALL WARRANTIES AND MAY CAUSE BODILY INJURY OR
EQUIPMENT DAMAGE. SERVICE PERFORMED BY OTHER THAN FACTORY AUTHORIZED PERSONNEL
WILL VOID ALL WARRANTIES.
WARNING: TURN OFF ELECTRIC POWER BEFORE WORKING ON INTERNAL COMPONENTS.
WARNING: BEFORE ANY CLEANING OPERATION, TURN THE THERMOSTAT TO “OFF” TO CUT OFF POWER TO
THE HEATING ELEMENTS. BEFORE CLEANING ANY PART OTHER THAN THE INSIDE OF THE PAN,
DISCONNECT THE ELECTRICAL SUPPLY AT THE CIRCUIT BREAKER OR FUSE BOX.

OM-BTD/FPC 3
WARNING: BE CAREFUL TO AVOID CONTACT WITH CLEANING PRODUCTS IN ACCORDANCE WITH SUPPLIER
AND MANUFACTURER RECOMMENDATIONS. MANY CLEANERS ARE HARMFUL TO THE SKIN, EYES,
MUCOUS MEMBRANES AND CLOTHING. READ THE WARNINGS AND FOLLOW DIRECTIONS ON THE
CLEANER LABEL.
CAUTION: NEVER LEAVE A CHLORINE SANITIZER IN CONTACT WITH STAINLESS STEEL FOR LONGER THAN 30
MINUTES. LONGER CONTACT CAN CAUSE CORROSION.
WARNING: DO NOT USE ANY FUSE WITH A HIGHER AMP RATING THAN THE RATING SPECIFIED FOR THAT
CIRCUIT.
IMPORTANT - READ FIRST - IMPORTANT

4 OM-TD/FPC
Important Operator Warnings ....................................................page 2-3
References.................................................................................... page 4
Equipment Description.................................................................. page 5
Inspection and Unpacking ............................................................ page 6
Initial Start-Up............................................................................... page 7
Operation ...................................................................................... page 8
Sequence of Operation ............................................................... page 9
Cleaning................................................................................... page 10-11
Maintenance................................................................................ page 11
Troubleshooting............................................................................ page 12
Wiring Diagram ....................................................................... page 15-16
Service Log ........................................................................... page 17-18
KLENZADE SALES CENTER ECOLAB. Inc.
370 Wabasha
St. Paul, Minnesota 55102
800/352-5326 or 612/293-2233
NATIONAL FIRE PROTECTION ASSOCIATION
60 Battery March Park
Quincy, Massachusetts 02269
NFPA/70 - The National Electrical Code
NSF INTERNATIONAL
789 N. Dixboro Road
P.O. Box 130140
Ann Arbor, Michigan 48113-0140
UNDERWRITERS LABORATORIES, INC.
333 Pngsten Road
Northbrook, Illinois 60062
ZEP MANUFACTURING CO.
1310-T Seaboard Industrial Blvd.
Atlanta, Georgia 30318
Table of Contents
References

OM-BTD/FPC 5
The 10-gallon, table top, electrically heated braising pan provides a 40 quart, stainless
steel pan body mounted for tilting and equipped with electric heating elements and a
thermostatic control. The braising pan serves as a braising unit, griddle, fry pan, kettle,
or bain-marie, and with optional equipment may be used also as an oven or food
warmer/server.
The pan body Is made of heavy-duty stainless steel welded into one piece with a
polished interior and semi-deluxe finish on the exterior. A pouring lip is molded into
the front wall. The cooking surface is stainless steel clad plate fitted with clamped-on
electric heating elements to provide efficient heat transfer over the entire surface.
The heating elements and all other electrical components of the unit are enclosed
for safety. The thermostat and indicator light are contained in a compact control
console mounted to the right of the pan body. Installation requires only one electrical
connection.
The pan body and control console are mounted on a base plate. A convenient handle
on the right side of the pan body facilitates tilting.
Optional equipment includes:
1. Fill faucet with swing spout
2. One piece, lift-off cover
3. Support stand
Equipment Description
BRAISING PAN CHARACTERISTICS
Capacity 10 gal (40 Quarts) 38 liters
Pan Width 18 inches (inside) 457 mm (inside)
Pan Length (front to back) 27 inches (inside) 686 mm (inside)
Pan Depth 7 inches 178 mm
Base Width 28.5 inches 724 mm
Base (front to back) 18 inches 457 mm
kW at 208 Volts 5.7 KW
kW at 240 Volts 6.0 KW
kW at 380 Volts 6.0 KW
kW at 480 Volts 6.0 KW

6 OM-TD/FPC
Internal wiring for the Braising Pan is supplied complete. When you receive the unit, it
is ready for connection. A wiring diagram is located inside the console on the side of
the pan, as well as in this manual.
Your pan was performance-tested at the factory to confirm that its controls and
heating elements were functioning correctly.
Installation is as follows:
1. Set the unit in place on a level surface. The unit must be level to avoid uneven
cooking across the pan.
2. Provide the proper electric power supply as specified on the electrical
information plate. Observe local codes and/or The National Electrical Code in
accordance with ANSI/NFPA 70 - latest edition.
3. Bringing the electrical service through the entrance in the control box, make
a waterproof connection with the incoming lines. A BX connection is not
recommended. GROUND THE UNIT ELECTRICALLY AT THE TERMINAL PROVIDED.
WARNING
THE BRAISING PAN MUST BE INSTALLED
BY PERSONNEL WHO ARE QUALIFIED TO
WORK WITH ELECTRICITY. IMPROPER
INSTALLATION COULD RESULT IN PERSONAL
INJURY OR EQUIPMENT DAMAGE.
Installation

OM-BTD/FPC 7
Initial Start-Up
Now that the Braising Pan has been installed, you should test it to ensure that it is
operating correctly.
1. Remove all literature and packing materials from the interior and exterior of the
unit.
2. Turn on the electrical power to the unit.
3. Put enough water into the pan to cover its bottom to a depth of ¼” to ½” (6 to 13
mm). With the pan body in the horizontal position, note how the water covers the
pan bottom. This is a good method to use for confirming that the unit is properly
leveled.
4. Set the thermostat to 235°F. The heating indicator light should come on to show
that the pan is heating. Heating should continue until the water boils.
5. To shut the unit down, turn the thermostat dial to “OFF.”
6. Position a container for the pour-off. Turn the handwheel clockwise to pour the
water out. This will confirm that the pan body tilts from horizontal to vertical.
CAUTION
STAND AWAY FROM THE HOT WATER
WHILE TILTING THE PAN TO EMPTY IT.

8 OM-TD/FPC
Operation
The operator controls braising pan operation with the thermostat dial, which is located
on the right front of the unit. Setting the dial sends electric power to turn the heaters
on or off and sets the operating temperature of the pan.
A. To Start Pan
1. Turn on the electric power supply to the unit.
2. Turn the thermostat dial to a desired setting between 100 and 400°F
(38 and 204°C). The red indicator light will glow, showing that the pan
is heating. The light will cycle on and off, which indicates that the pan is
being held at the set temperature. Once in each cycle the contactors in the
control box will make a clicking sound. This is normal.
3. For best braising or frying results, preheat the pan before you put in any
food. To get an even temperature across the pan, preheat at a setting of
300°F (149°C) or less for 15 minutes (several thermostat on/off cycles).
B. Cooking
1. To simmer or slowly heat an item, set the dial at about 210°F (99°C)
or lower. Put the optional cover on the pan to keep moisture loss at
a minimum, or leave it off to help dry or reduce the product. Set the
thermostat higher to cook or drive moisture off faster. The thermostat may
be adjusted to any setting in its range to cook exactly as you wish.
2. When using the optional cover, leave the cover vent open to allow excess
steam to escape. For longer simmering, you may wish to close the vent to
retain moisture.
3. Be careful when lifting the optional cover. Lift its rear edge a few inches to
allow any steam or and hot vapor to escape the pan. Then tilt it further to
allow any hot condensate to roll off the cover and back into the pan.
4. To pour or dump product, remove grease, or assist cleaning, first remove
the cover, then tilt the pan. Be careful!
C. To Shut Down the Pan
1. Turn the thermostat dial to “OFF”.
2. For prolonged shut-down, or before cleaning the outside of the unit,
completely shut off the power supply to the unit.
D. Routine Cleaning
After each use, turn the thermostat to ”OFF” and clean all food-contact surfaces.
At the end of each day, or at least once every 12 hours, turn off electric power
to the unit, and clean both the interior and the exterior. See detailed cleaning
instructions in the Maintenance section of this manual.
WARNING
DO NOT HEAT AN EMPTY PAN FOR MORE
THAN FIVE MINUTES AT SETTINGS ABOVE
300°F. DAMAGE TO THE PAN COULD RESULT.
WARNING
AVOID ANY EXPOSURE TO THE STEAM
ESCAPING FROM THE COVER VENT.
DIRECT CONTACT COULD RESULT IN
SEVERE BURNS.
WARNING
AVOID ALL DIRECT CONTACT WITH HOT
EQUIPMENT SURFACES. DIRECT SKIN
CONTACT COULD RESULT IN SEVERE BURNS.
AVOID ALL DIRECT CONTACT WITH HOT
FOOD OR WATER IN THE BRAISING PAN.
DIRECT CONTACT COULD RESULT
IN SEVERE BURNS.
WARNING
IF THE PAN CONTAINS ITEMS IN SAUCE OR
MELTED FAT, THEY COULD SLIDE FORWARD
SUDDENLY DURING TILTING AND CAUSE THE
HOT LIQUID TO SPLASH OUT.

OM-BTD/FPC 9
Sequence of Operation
The following “action-reaction” outline is provided to help you understand how the
braising pan actually functions.
When you start the pan by turning the thermostat dial from “OFF” to a desired
temperature, the thermostat switch closes. This action causes the contactors to close,
allowing power to flow to the heating elements and the indicator light. When the
temperature of the pan rises to the value set on the thermostat dial, the thermostat
switch opens and causes the contactors to open. This stops the flow of power to the
heaters and indicator light.
As soon as the thermostat senses that the pan has cooled below the set temperature,
the thermostat switch closes, the contactors close, and the heaters and indicator light
come on again.
This on-off cycling continues, holding the pan at the set temperature. These cycles
cause the indicator light to go on and off during normal operation.
If the pan temperature rises above 425°F (218°C) for any reason, a high-limit
thermostat shuts off power until the pan cools. At that point the thermostat
automatically resets and allows normal operation to begin again.
Setting the thermostat dial to “OFF” shuts down all control and heating circuits.
The thermostat controls heating by alternately feeding full power and completely
cutting off power. The pan will heat as fast as it can until it reaches the set
temperature, no matter what that temperature is. Turning the thermostat dial to a
higher setting will only cause heating to continue longer, until the pan reaches the
higher temperature. It will not make the pan heat any faster.

10 OM-TD/FPC
Cleaning
WARNING
BEFORE ANY CLEANING OPERATION,
TURN THERMOSTAT DIAL TO “OFF” TO
CUT ANY POWER TO THE HEATING
ELEMENTS. BEFORE CLEANING ANY PART
OTHER THAN THE INSIDE OF THE PAN,
DISCONNECT ELECTRICAL SUPPLY AT
CIRCUIT BREAKER OR FUSE BOX.
A. Suggested Tools
1. Cleaner, such as Klenzade
2. Brushes in good condition
3. Cloth for cleaning controls
4. Chlorine sanitizer such as Klenzade
5. Heavy Duty Cleaner, such as Klenzade LC-30
B. Procedure
1. Clean all food-contact surfaces soon after use. It is best to clean the pan
before it has completely cooled. If the unit is in continuous use, completely
clean and sanitize both the inside and outside at least once every 12 hours.
2. To remove any large amount of food left in the pan, tilt the pan all the way
up and flush it with lukewarm water. Do not damage the surface of the pan
by scraping it with a metal tool. Scratches make the surface more difficult
to clean, and provide ideal breeding places for bacteria.
3. Following the supplier’s directions, make up a warm solution of the cleaner.
Carefully wash the inside and outside of the pan body with the cleaning
solution.
4. Use a cloth moistened with cleaning solution to clean controls, the control
console, and electric conduit.
5. Rinse the pan very well with lukewarm water, and drain it completely.
6. As part of the daily cleaning program, clean all inside and outside surfaces
that may have been soiled. Remember to check such parts as the electri-
cal console and other remote spots. Clean between the pan body and the
console using a brush.
7. To remove materials stuck to the equipment, use a brush, sponge, cloth,
plastic or rubber scraper, or plastic wool with the cleaning solution. To
make washing easier, let the cleaning solution sit in the unit and soak
into the residue, or briefly heat the solution. Do not use any gritty cleaner
or metal tool that might scratch the surface. Scratches make the surface
harder to clean and provide places for bacteria to grow. Do not use steel
wool. Small bits of steel wool left in the surface of the unit can cause rust-
ing and pitting.
8. The outside of the unit may be polished with a recognized stainless steel
cleaner such as Zepper from the Zep Manufacturing Company.
9. When the equipment needs to be sanitized, use a sanitizing solution
equivalent to one that supplies 100 parts per million available chlorine.
Get advice about the best sanitizing agent from you supplier of sanitizing
products.
10. Following supplier instructions, apply the sanitizing agent after the unit has
been cleaned and drained. Thoroughly drain off the sanitizer.
CAUTION
KEEP WATER AND CLEANING SOLUTIONS
OUT OF CONTROLS AND ELECTRICAL
EQUIPMENT. DO NOT SPRAY OR HOSE
THE CONTROL BOX OR OTHER
ELECTRICAL CONNECTIONS. THEY ARE
NOT WATER-PROOF.
Don’t use metal implements or
steel wool when cleaning.
Use a brush, sponge, cloth, plastic or
rubber scraper, or plastic wool to clean.
CAUTION
MOST CLEANERS ARE HARMFUL TO THE
SKIN, EYES, MUCOUS MEMBRANES, AND
CLOTHING. PRECAUTIONS SHOULD BE
TAKEN. WEAR RUBBER GLOVES,
GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. READ THE
WARNINGS AND CAREFULLY FOLLOW THE
DIRECTIONS ON THE CLEANER LABEL.

OM-BTD/FPC 11
CAUTION
NEVER LEAVE A CHLORINE SANITIZER IN
CONTACT WITH STAINLESS STEEL
SURFACES FOR LONGER THAN 30 MINUTES.
LONGER CONTACT CAN CAUSE CORROSION.
Cleaning
11. After the unit has been cleaned, sanitized and drained, let all surfaces air
dry unless the unit must be used again right away.
12. It is recommended that the unit be sanitized just before use. Follow the
directions of the sanitizer supplier.
13. About once a week (more often if the water is very hard), use a heavy duty
cleaner to remove mineral deposits or film left by hard water or foods. Fol-
low the supplier’s directions very carefully, and thoroughly rinse the unit off
as soon as cleaning is finished.
14. If especially difficult cleaning problems persist, contact your cleaning
product supplier for help. The supplier has a trained technical staff with
laboratory facilities to serve you.
Maintenance
Your Braising Pan is designed to require minimum maintenance, but some parts may
require replacement after prolonged use. After installation, no user adjustment should be
necessary. If a service need arises, only authorized personnel should perform the work.
Service personnel should check the unit at least once a year. This should include
inspecting wires and connections and cleaning inside the control console. A Maintenance
and Service Log is provided at the rear of this manual. Each time work is performed,
enter the date on which it was done, what was done, and who did it.
WARNING
USE OF REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY THE MANUFACTURER OR
AN AUTHORIZED DISTRIBUTOR CAN CAUSE
INJURY TO THE OPERATOR AND DAMAGE
TO THE EQUIPMENT AND WILL VOID ALL
WARRANTIES.SERVICE PERFORMED BY OTHER
THAN FACTORY-AUTHORIZED PERSONNEL WILL
VOID ALL WARRANTIES.
WARNING
ELECTRICAL POWER MUST BE SHUT OFF
BEFORE WORK IS DONE ON INTERNAL
COMPONENTS.

12 OM-TD/FPC
Troubleshooting
Your Braising Pan will operate smoothly and efficiently if properly maintained. However, the following is a list of checks to make in
the event of a problem. If the actions suggested do not solve the problem, call your authorized Service Representative. For the phone
number of the nearest agency, call your area representative or the Parts and Service Department. If an item on the list is followed by
X, the work should only be performed by a qualified service representative.
SYMPTOM WHO WHAT TO CHECK
Pan will not heat, but
indicator light comes on.
Authorized
Service Rep Only
a. Heating elements for short circuit. X
Pan will not heat, and indicator
light will not light.
User a. That power supply is on.
b. Fuse(s).
Authorized
Service Rep Only
c. For loose or broken wires. X
d. Thermostat functioning, by listening for a click when the switch opens or closes. X
e. Contactor functioning. X
Pan continues to heat after it
reaches desired temperature.
User a. Thermostat dial setting. Turn down if too high.
Authorized
Service Rep Only
b. Thermostat functioning. X
c. Thermostat calibration. X
d. Contactor, to determine if it is de-energized. X
Pan does not reach
desired temperature.
User a. Thermostat dial setting. Turn up if too low.
Authorized
Service Rep Only
b. Heating elements for ground short or open (burned out) element. X
c. Thermostat functioning, by listening for a click when the switch opens or closes. X
d. Thermostat calibration. X
e. Contactor functioning. X
Rapid clicking noise
(chattering).
User a. For low voltage.
Authorized
Service Rep Only
b. Contactor for dirt or corrosion on the contacts. X
Uneven cooking due to
“hot spots.”
User a. That the pan body is level.
Uneven cooking due to
“cold spots.”
Authorized
Service Rep Only
a. For open (burned out) heating element. X
b. That elements are fastened tightly to pan body. X
c. That the pan body is level. X
WARNING
USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY THE MANUFACTURER OR THEIR AUTHORIZED DISTRIBUTORS
CAN CAUSE INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND WILL VOID ALL WARRANTIES. SERVICE PERFORMED
BY OTHER THAN FACTORY-AUTHORIZED PERSONNEL WILL VOID ALL WARRANTIES.

OM-BTD/FPC 13
To order parts, contact your authorized Service Agency. Supply the model designation (TD/FPC), part description, part number and
quantity required. Where applicable, provide the voltage and phase as well.
KEY DESCRIPTION PART NO.
1 Outboard Support Assembly 003696
2 Thermostat, High Limit 012840
3 Clamp, Strip Heater 012844
4 Bar, Bus, 36” 012845
5 Heater, Strip 208 Volt,
950 Watts
012842
5 Heater, Strip 240 Volt,
1000 Watts
012843
5 Heater, Strip 480 Volt,
1000 Watts
012908
6 Transformer, 380 Volt 001860
6 Transformer, 480 Volt 012827
7 Fuse, 1 AMP, 480 Volt 004324
8 Contactor, 208 & 240 Volt,
1 Phase
009178
8 Contactor, 208 & 240 Volt,
3 Phase
009210
8 Contactor, 480 Volt, 3 Phase 009574
9 Block, Terminal 003119
10 Thermostat, Control 012838
11 Knob, Thermostat 003908
12 Light, Indicator,
208 & 240 Volt
016028
12 Light, Indicator, 480 Volt 002986
13 Block, Pillow, 1-1/2” ID 002989
14 Collar, Set 1-1/2” ID 003118
15 Washer, Plain. 1/2” 002213
16 Tilt Detent Assembly 002970
17 Nut, Cap, 3/8-24 003188
18 Washer, Lock, 3/8 005618
19 Handle 012694
Parts List

14 OM-TD/FPC
Electrical Parts
CONTACTOR HEATER INDICATOR LIGHT TRANSFORMER
MODEL Qty Part No. Qty Part No. Part No. Part No.
208 V/1 Ph 1 9178 6 12842 16028 None
208 V/3 Ph 1 9210 6 12842 16028 None
240 V/1 Ph 1 9178 6 12843 16028 None
240 V/3 Ph 1 9210 6 12843 16028 None
380 V/3 Ph 1 9574 6 12843 2986 1860
480 V/3 Ph 1 9574 6 12908 2986 12827

OM-BTD/FPC 15
Wiring Diagram

16 OM-TD/FPC
Wiring Diagram

OM-BTD/FPC 17
Service Log
Model No: Purchased From:
Serial No: Location:
Date Purchased: Date Installed:
Purchase Order No: For Service Call:
Date Maintenance Performed Performed By

18 OM-TD/FPC
Service Log
Model No: Purchased From:
Serial No: Location:
Date Purchased: Date Installed:
Purchase Order No: For Service Call:
Date Maintenance Performed Performed By

OM-BTD/FPC 19

PART NUMBER 121066, REV. D (04/11)
1055 Mendell Davis Drive • Jackson MS 39272
888-994-7636 • 601-372-3903 • Fax [phone]
unifiedbrands.net
© 2011 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.