Grohe Grohtherm Wireless User manual

D.....1 I.....2 N.....3 GR .....5 TR .....6 BG .....7 RO .....9
GB .....1 NL .....2 FIN .....4 CZ .....5 SK .....6 EST .....8 RUS .....9
F.....1 S.....3 PL .....4 H.....5 SLO .....7 LV .....8
E.....2 DK .....3 UAE .....4 P.....6 HR .....7 LT .....8
Grohtherm Wireless!
Grohtherm Wireless!
95.668.131/ÄM 207883/05.07
Installation Instructions

Please pass these instructions on to the end user!
1 2

4A
A
B
3
X
2 5
C
D
B
E
9*28 407
7
1.
2.
3.
10
6
Ø6
500-900
33
65
Ø25
1
8
43

5
Installation
This shower combination allows water
connection by two different methods. All
parts for both executions are contained in the
product.
Options are:
•Connection via elbow outlet, see Page 3,
Fig. [1].
•Connection via telescopic pipe set, see
Page 3, Fig. [2].
For the decision please pay attention to local
electric wiring and water lines.
Refer to the dimensional drawing on
Page 1.
Elbow outlet method
1.Lay out and install elbow outlet if used, see
Fig. [3].
2.Insert non-return valve (X)
Telescopic pipe set method
1.Lay out telescopic pipe set if used and sho-
wer rail in accordance to the dimensions
given in Fig. [2].
2.Pull off caps (A) from shower rail (B), see
Fig. [4].
3.Push glide bush (C) to the top end of the
shower rail (B) and insert tube (D) of
telescopic pipe set, see Fig. [5].
4.Mount push fit connection (E) to Ø 15mm
copper pipe (not included).
5.Insert Ø 15mm copper pipe with push fit
connection (E) in shower rail from below
and fasten.
Shower Rail
-Install shower rail for both installation
possibilities, see Pages 4 and 7, Figs. [6]
to [13].
Fix telescopic pipe set
1.Push on ceiling rosette (G), see Page 7,
Fig. [14].
2.Feed the tube (D) and Ø 15mm copper
pipe through deck / ceiling, cover with
ceiling clamp (H) and fasten, see Fig. [15].
3.Mount ceiling clamp (H) with screws (I) to
deck / ceiling.
4.Secure Ø 15mm copper pipe by turning the
push fit (J), see Fig. [16].
Handspray
1.Insert throttle (Y) into hand shower, see
Page 8, Fig. [17].
2.Tighten hose (K) by hand only.
3.Connect hose to elbow outlet or bottom of
shower rail.
Setting the spray types
By turning the adjusting ring (L), the different
spray types can be set, see Fig. [17].
Shower head positions
By pressing the button (M), the shower head
can be adjusted in 45° steps, Fig. [17].
•Position as hand shower, see Fig. [18].
•Position as side shower, see Fig. [19].
•Position for e. g. cleaning purposes, see
Fig. [20].
Connect mixed water outlet of Base Unit to
shower combination.
Open cold and hot water supply.
Check the pipework and connections to the
shower controller for leaks.
The Shower Set is now ready for use.
Installation

6
Inspect and clean all parts, replace as
necessary and grease with special grease.
Disassembling handspray, see Fig. [21].
Unscrew spray face plate (N) using a 3mm
allen key.
Assemble in reverse order.
•Grease seals (O) of spray face plate (P).
•When reassembling the spray face
plate (N), the stop (P) must be at the back.
•Filter (R) must always be re-installed!
Quick-decalcification, see Fig. [22].
We guarantee that the SpeedClean nozzles
will function unchanged for a period of 5
years. With SpeedClean nozzles simply rub
fingers over the rose to remove limescale.
Care
For directions on care, refer to the
accompanying Care Instructions.
Maintenance
Replacement Parts
No. Description Cat.-No. Pack- ing
unit
4 Sliding Rail Element 12 353 1
5 Non-Return Valve 08 565 1
Optional accessory
6 Spacer Disc 28 407 1
No. Description Cat.-No. Pack- ing
unit
1 Seal 06 768 5
2 Cover Cap 11 482 1
3 Bracket 45 923 1
3.1 Fixing Set 45 924 1

3mm
11
13
15
H
D
I
12 17
L
M
K
Y
18
19 2014 G
D
16
J
21
3mm
N
R
O
P
O
22
7 8