Grossenbacher Systeme WebPanel WP-284 Series User manual

WebPanel
WP-284-x
Grossenbacher Systems AG
Spinnereistrasse 10, CH-9008 St. Gallen
T [phone] / F [phone]
info gesys.ch / www.gesys.ch
Grossenbacher Systems GmbH
Feldwiesenstrasse 8, DE-79807 Lottstetten
T [phone] / F [phone]
sales.de gesys.ch
OPERATING INSTR CTIONS
ARM
i.MX 8
Quad

WebPanel
WP-284-x
Grossenbacher Systems AG
Spinnereistrasse 10, CH-9008 St. Gallen
T [phone] / F [phone]
info gesys.ch / www.gesys.ch
Grossenbacher Systems GmbH
Feldwiesenstrasse 8, DE-79807 Lottstetten
T [phone] / F [phone]
sales.de gesys.ch
Copyright notice
These operating instructions and all illustrations contained therein are protected by copy-
right. Any use outside the limits of copyright law is prohibited without the prior written
consent of Grossenbacher Systeme AG and is punishable by law. This applies to
reproductions, translations, microfilming, storage, and processing in electronic systems.
The Grossenbacher Systeme AG accepts no liability for damage, caused by the use of
incorrect or inadequate information or due to missing information in these documents.
The Grossenbacher Systeme AG reserves the right to change this document in part or in
full.
All brand and product names are trademarks or registered trademarks of their respective
titleholders/owners.
Overview of changes
Version Date of issue Change / Remark
01 15.11.2023 / wm First release in English.
Bases on German version with Doc-ID 122514-03.
02 14.12.2023 / wm Corrections, additions, and alignments with the SmartPanel
operating instructions.
Bases on German version with Doc-ID 122514-04.

Contents
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
I
-
Contents
1 Introduction ........................................................................................................................... 3
1.1 Means of presentation ............................................................................................................... 3
1.1.1 Section-related warnings ................................................................................................ 3
1.1.2 Embedded warnings ....................................................................................................... 4
1.1.3 Other means of presentation ......................................................................................... 4
1.2 Symbols used in the instructions ............................................................................................... 5
1.3 Warranty and liability ................................................................................................................. 5
1.4 Applicable documents ............................................................................................................... 5
1.5 Order numbers WP-284-x .......................................................................................................... 6
1.6 Service / Product support .......................................................................................................... 6
2 Security .................................................................................................................................. 7
2.1 Intended use .............................................................................................................................. 7
2.1.1 Structural changes to the devices .................................................................................. 7
2.1.2 Foreseeable misuse ........................................................................................................ 7
2.2 Requirements for personnel ...................................................................................................... 8
3 Description ............................................................................................................................. 9
3.1 Device overviews ....................................................................................................................... 9
3.1.1 Devices for VESA mounting ............................................................................................ 9
3.1.2 Devices for front installation ........................................................................................ 10
3.2 Connections / Interfaces .......................................................................................................... 11
3.3 Technical data .......................................................................................................................... 12
3.3.1 Dimensions ................................................................................................................... 12
3.3.2 Power supply / Power consumption ............................................................................ 12
3.3.3 Electromagnetic compatibility / Protection class ......................................................... 14
3.3.4 Specifications ................................................................................................................ 15
3.3.5 Ambient conditions ...................................................................................................... 16
3.3.6 Certification .................................................................................................................. 16
4 Transportation / Storage / Scope of delivery ......................................................................... 17
4.1 Transportation .......................................................................................................................... 17
4.2 Storage ..................................................................................................................................... 17
4.3 Scope of delivery ...................................................................................................................... 17
5 Assembly .............................................................................................................................. 19
5.1 Preparatory measures .............................................................................................................. 19
5.2 Dimensions / Installation cut-out............................................................................................. 20
5.2.1 WP-284-07P-000 (7.0" front installation) ..................................................................... 20
5.2.2 WP-284-10P-000 (10.1" front installation) ................................................................... 22
5.2.3 WP-284-15P-000 (15.6" front installation) ................................................................... 24
5.2.4 WP-284-18P-000 (18.5" front installation) ................................................................... 26
5.2.5 WP-284-07P-000 (7.0" VESA) ....................................................................................... 28
5.2.6 WP-284-10P-000 (10.1" VESA) ..................................................................................... 29

Contents
-
II
-
Doc
-
ID: 1
22515
-
02
WP
-
284
-
x
5.2.7 WP-284-15P-000 (15.6" VESA) ...................................................................................... 30
5.3 Device installation ................................................................................................................... 31
6 Connection ............................................................................................................................ 33
6.1 Power supply ........................................................................................................................... 33
6.2 Data connections ..................................................................................................................... 36
6.2.1 Ethernet interface ......................................................................................................... 36
6.2.2 USB interface ................................................................................................................ 38
7 ser interface ....................................................................................................................... 39
7.1 Setup menu ............................................................................................................................. 39
7.2 Access to the setup menu ....................................................................................................... 40
7.3 Configure network .................................................................................................................. 41
7.4 Configure server ...................................................................................................................... 42
7.5 Save/reject settings ................................................................................................................. 42
8 Cleaning / Repairs ................................................................................................................. 43
8.1 Cleaning ................................................................................................................................... 43
8.2 Repairs ..................................................................................................................................... 43
9 Disposal ................................................................................................................................ 45

1 Introduction
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
3
-
1Introduction
These operating instructions are an integral part of the WebPanel device series WP-284-x
(hereinafter referred to as device, devices or WebPanel).
The operating instructions must be read, understood, and applied by all persons responsible
for installing the devices.
In addition to the operating instructions, generally applicable, statutory, and other binding
regulations on accident prevention and environmental protection in the country of use
must be observed.
1.1 Means of presentation
As a note and as a direct warning of dangers, text passages in these operating instructions
that require special attention are marked as follows:
1.1.1 Section-related warnings
Section-related warnings apply not only to a specific action, but to all actions within a
section.
Structure
SIGNAL WORD
Symbol to
explain the
danger
Nature
and source of
the
danger
Possible consequences of non-compliance
►Measures to avoid the danger
Hazard levels
DANGER
Danger with a high degree of risk
If the danger is not avoided, this will result in death or serious injury.
WARNING
Danger with medium degree of risk
If the danger is not avoided, it can result in death or serious injury.

1 Introduction
-
4
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
CA TION
Danger with low risk level
If the danger is not avoided, this may result in minor or moderate bodily
injury.
NOTE
Risk of property damage with a low degree of risk
If the danger is not avoided, this can result in material damage.
1.1.2 Embedded warnings
Embedded warnings apply to specific actions and are directly integrated into the action.
Structure
SIGNALWORD Nature and source of danger
Possible consequences of non-compliance
►Measures to avoid the danger
Hazard levels
‒ DANGER / WARNING / CA TION
‒ NOTE
For explanations of the hazard levels, see chapter "1.1.1".
1.1.3 Other means of presentation
The info symbol refers to important information about the device.
- Texts that follow this marking are enumerations.
►
Texts that follow this marking describe measures in warnings and action steps.
" "
Texts in quotation marks are references to other chapters or sections.

1 Introduction
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
5
-
1.2 Symbols used in the instructions
In warnings, special dangers are additionally marked as follows:
Danger to life due to electric current
This symbol warns of the danger to life from electric current.
General dangers
This symbol warns of general dangers that can occur during all phases
of the device's life.
ESD protection measures
This symbol warns of destruction due to electrostatic discharges on
electronic components if ESD protective measures are not observed.
1.3 Warranty and liability
The obligations agreed in the delivery contract, the general terms and conditions, as well as
the delivery conditions of the device(s) and the statutory regulations, valid at the time the
contract is concluded, shall apply.
All information and notes in these operating instructions have been compiled taking into
account the applicable standards and regulations, the state of the art and our many years of
knowledge and experience.
Warranty and liability claim for personal injury and damage to property are excluded if they
are attributable to one or more of the following causes:
‒Defects caused by improper use or improper handling of the devices
‒Consequential damage caused by failure or malfunction of the device(s)
‒Non-observance of the operating instructions
‒Use of unqualified or untrained personnel
‒Structural modifications to the devices
1.4 Applicable documents
Document Document No.
No document defined -

1 Introduction
-
6
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
1.5 Order numbers WP-284-x
Type Format Structure / Mounting Order number
WP-284-07P-003 7.0" Front installation 5082033
WP-284-10P-002 10.1" Front installation 5082031
WP-284-15P-002 15.6" Front installation 5082032
WP-284-18P-000 18.5" Front installation 5082039
WP-284-07P-004 7.0" VESA 5082035
WP-284-10P-003 10.1" VESA 5082041
WP-284-15P-003 15.6" VESA 5082042
1.6 Service / Product support
For technical information, please contact our customer service:
Manufacturer address Representation Germany
Grossenbacher Systems AG
Spinnereistrasse 10
CH-9008 St. Gallen
Switzerland
Grossenbacher Systems GmbH
Feldwiesenstrasse 8
DE-79807 Lottstetten
Germany
Tel: [phone]
Fax: [phone]
E-Mail: info gesys.ch
Homepage: www.gesys.ch
Tel: [phone]
Fax: [phone]
E-Mail: sales.de gesys.ch
Homepage: www.gesys.ch
In addition, our employees are constantly interested in new information and experiences
that result from the application and can be valuable for the improvement of our products.

2 Security
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
7
-
2Security
►Read the operating instructions thoroughly before installing and connecting the devices.
►In addition to the operating instructions, also observe the existing national/regional
work safety and accident prevention regulations.
2.1 Intended use
The devices are designed for use in industrial and commercial applications.
The operational safety of the devices is only guaranteed if they are used as intended.
The devices are designed exclusively for
‒indoor use,
‒installation in higher-level machines/systems,
‒the visualization of control processes in machines/systems.
These devices are equipment of protection class III and may only be supplied with safety
extra-low voltage (SELV/PELV).
The devices are not intended for any use other than that listed here; this is considered
improper use.
Intended use also includes
‒observance of the operating instructions,
‒compliance with the operating conditions and technical specifications.
2.1.1 Structural changes to the devices
Structural changes (extensions and conversions) mean that warranty and liability claim for
personal injury and property damage are excluded.
►Replace devices that are not in perfect condition immediately.
Parts and components that are not supplied by Grossenbacher Systeme AG are not
approved for use on the devices.
2.1.2 Foreseeable misuse
Any use of the devices that goes beyond the intended use and/or any other use may result
in damage to the devices.
In particular:
‒The devices must not be switched on when dew is present. After a change of location
from cold to warm, the temperature of the devices must be allowed to equalize before
commissioning.
‒No safety-relevant functions - in terms of personal, machine and system protection - may
be implemented via the devices.

2 Security
-
8
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
2.2 Requirements for personnel
The devices may only be installed, connected, commissioned, and repaired by technically
qualified personnel.
Technically qualified personnel
Technically qualified staff is
‒as project planning personnel, familiar with the safety concepts of automation
technology.
or
‒has been instructed as operating personnel in the use of automation technology
equipment and has knowledge of how to operate the devices.
or
‒are qualified to carry out repairs on such equipment as commissioning and service
personnel, as a result of competent training in automation technology.
or
‒are qualified to commission circuits and devices/systems in accordance with safety
engineering standards.
Obligation of the staff
All persons responsible for installation are obliged to observe the basic regulations on work
safety and accident prevention and to read the safety instructions and warnings in these
operating instructions.

3 Description
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
9
-
3Description
The WebPanel device series WP-284-x is based on a powerful and energy-efficient RISC
processors (Arm Cortex-A) and is used in the function of a web browser (web panel) for
display and operation (HMI) in industrial and commercial environments.
3.1 Device overviews
3.1.1 Devices for VESA mounting
The following illustration shows the structure of the device for VESA mounting, using the
10.1-inch version as an example. The structure of the 7.0-inch and 15.6-inch versions is
identical to that of the 10.1-inch version.
Pos. Element
1 Display
2 Holder for VESA mounting

3 Description
-
10
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
3.1.2 Devices for front installation
The following illustration shows the structure of the device for front installation, as an
example in the 10.1-inch version. The structure of the 7.0-inch, 15.6-inch and 18.5-inch
versions is identical to that of the 10.1-inch version.
Pos. Element
1 Counter frame
2 Display
3 Round cord (Ø 3 mm)
4 Lock nut
Version for 7.0-inch, 10.1-inch: M4
Version for 15.6-inch, 18.5-inch: M5

3 Description
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
11
-
3.2 Connections / Interfaces
The pin assignment and interfaces are the same for the devices in the device series
WP-284-x (VESA mounting and front installation) and are designed identically.
Pos. Element Abbreviation Description
1 Ethernet (LAN) ETH see chapter "6.2.1"
2 USB USB see chapter "6.2.2"
3 Power supply Supply see chapter "6.1"

3 Description
-
12
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
3.3 Technical data
3.3.1 Dimensions
Device Format Structure /
Installation type
Length
(mm)
Width
(mm)
Depth
(mm)
WP-284-07P-003 7.0" Front installation 205.0 144.0 35.5
WP-284-10P-002 10.1" Front installation 269.4 185.7 35.5
WP-284-15P-002 15.6" Front installation 404.0 251.0 38.5
WP-284-18P-000 18.5" Front installation 470.0 290.0 44.5
WP-284-07P-004 7.0" VESA 197.0 136.0 41.1
WP-284-10P-003 10.1" VESA 261.0 177.3 41.1
WP-284-15P-003 15.6" VESA 395.6 242.6 45.0
3.3.2 Power supply / Power consumption
Parameters Value
Nominal voltage +24 VDC
Protective extra-low voltage (PELV), protection class III
Permissible voltage range 19.2 - 30.0 VDC, absolute with ripple
(nominal voltage -20/-25 %)
Transient 35.0 V, for a duration < 100 ms
Electrical isolation No
0V-terminal connected to housing potential (FE)
Reverse polarity protection Yes, diode
No operation possible if polarity is reversed
Protection fuse
(interrupting capability)
Yes, lead fuse,
cannot be changed from outside
(1)
7.0": 1.5 AT (300A 32VDC)
10.1": 1.5 AT (300A 32VDC)
15.6": 1.5 AT (300A 32VDC)
18.5": 2.5 AT (300A 32VDC)
Max. current consumption
(2)
in operation without backup
charging current
7.0": 0.70 A 24V (0.85 A 19.2V)
10.1": 0.60 A 24V (0.75 A 19.2V)
15.6": 0.90 A 24V (1.15 A 19.2V)
18.5": 1.45 A 24V (1.80 A 19.2V)

3 Description
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
13
-
Parameters Value
Max. current consumption
(2)
with backup charging current
7.0": 0.95 A 19.2V
10.1": 0.85 A 19.2V
15.6": 1.25 A 19.2V
18.5": 2.30 A 19.2V
Max. inrush current (I
2
t) 7.0": 0.7 A
2
s
10.1": 0.7 A
2
s
15.6": 0.7 A
2
s
18.5": 0.06 A
2
s
Max. power consumption
(2)
w/o backup charging current
7.0": 16.0 W (13.0 W w/o load on USB port)
10.1": 14.0 W (11.0 W w/o load on USB port)
15.6": 21.5 W (18.5 W w/o load on USB port)
18.5": 34.5 W (31.5 W w/o load on USB port)
Backup charging current
(2)
(after power on)
7.0": 2.0 W peak, time constant (τ) 220 ms
10.1": 2.0 W peak, time constant (τ) 220 ms
15.6": 2.0 W peak, time constant (τ) 220 ms
18.5": maximum 10 W, for a maximum of 4 s
Voltage dips and bridging
(3)
(backup)
7.0": typ. 18 ms 24V (min. 8 ms)
10.1": typ. 18 ms 24V (min. 8 ms)
15.6": typ. 18 ms 24V (min. 8 ms)
18.5": min. 60 ms, over the entire voltage range
Max. load current at the USB
port
0.5 A (high powered port), current-limited,
short-circuit-proof
(1) The fuse can/may only be replaced by service personnel from Grossenbacher
Systeme AG.
(2) After switching on or a voltage dip with bridging, the backup storage is
charging/recharging for a short time (backup charging current after power on).
This additional power must be considered when determining the maximum power
consumption and current limit of the power supply.
(3) Bridging of short voltage dips, with temporary display backlight switch-off

3 Description
-
14
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
3.3.3 Electromagnetic compatibility / Protection class
Parameters Execution
EMC immunity Interference immunity for industrial environments,
in accordance with EN 61000-6-2
EMC interference
radiation
Interference emission for residential, commercial and
light-industrial environments,
in accordance with EN 61000-6-3
Protection class
(4)
Front component of the device: IP 65
Rear component of the device: IP 20
(4) IP protection class according to comparable device design.
The device is only suitable for indoor use.

3 Description
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
15
-
3.3.4 Specifications
Kind Execution
Screen technology TFT-LCD
Screen size
and resolution
7.0": 1024 x 600 (WSVGA, 16:9)
10.1": 1280 x 800 (WXGA, 16:10)
15.6": 1366 x 768 (HD, 16:9)
18.5": 1920 x 1080 (FHD, 16:9)
Display area 7.0": 154 x 86 mm
10.1": 217 x 136 mm
15.6": 344 x 194 mm
18.5": 409 x 230 mm
Image contrast 500:1
Backlight
(5)
LED, dimmable via software
Service life: 50000 hours
Brightness: 350 cd/m
2
Touch screen PCAP touch
Processor Arm Cortex-A53, NXP i.MX8M-Mini, Quad Core
Working memory 2 GB, DDR4, soldered
Nonvolatile memory (SSD) 8 GB, MLC eMMC, soldered
Real-time clock (RTC) not available
Communication interfaces Ethernet: Gigabit (1000Base-T)
USB: USB host 2.0, type A, 1.5/12/480 Mb/s
Device cooling passive (fan-less)
Cover glass Scratch-resistant glass,
glass thickness typ. 1 mm
(5) The intensity of the display backlighting can be set by the application. The backlight is
temporarily switched off, in the event of power supply interruptions, which can be
detected and bridged by the system.

3 Description
-
16
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x
3.3.5 Ambient conditions
Kind Condition
Climate operation Temperature
(6)
: 0 - 50 °C
Rel. humidity: 10 - 85 %, non-condensing
Climate storage/transport Temperature: -20 - 70 °C
Rel. humidity: 10 - 85 %, non-condensing
Vibration operation 10 - 53 Hz: 0.35 mm
53 - 500 Hz: 2 g
Vibration transport 10 - 84 Hz: 0.35 mm
84 - 500 Hz: 5 g
Shock 15 g / 11 ms
Max. height for operation 2000 m above sea level
(6) Temperature measurement: 5 cm below the WebPanel (vertical installation).
3.3.6 Certification
Device Format Structure /
Mounting
Certification
WP-284-07P-003 7.0" Front installation CE
WP-284-10P-002 10.1" Front installation CE, UL approval (AZOT2.E492671)
WP-284-15P-002 15.6" Front installation CE
WP-284-18P-000 18.5" Front installation CE
WP-284-07P-004 7.0" VESA CE
WP-284-10P-003 10.1" VESA CE, UL approval (AZOT2.E492671)
WP-284-15P-003 15.6" VESA CE

4 Transportation / Storage / Scope of delivery
WP
-
284
-
x
Doc
-
ID: 122515
-
02
-
17
-
4Transportation / Storage / Scope of delivery
4.1 Transportation
Check for transport damage
►Check the device for visible transport damage and report any transport damage
immediately to the delivery office.
Protection of the device
►Only use the original packaging to transport the device.
►Observe the ambient conditions (see chapter "3.3.5").
4.2 Storage
►Observe the ambient conditions (see chapter "3.3.5").
Recommendation: Store the unit at room temperature.
4.3 Scope of delivery
WebPanel for front installation
The scope of delivery of the device consists of the following components:
‒WebPanel
‒Round cord seal
‒Counter frame
‒4x lock nut, M4 or M5 (depending on version)
‒3-pin power supply connector, MSTB 2,5/ 3-STF-5,08 (Phoenix Contact, or compatible)
WebPanel for VESA mounting
The scope of delivery of the device consists of the following components:
‒WebPanel
‒3-pin power supply connector, MSTB 2,5/ 3-STF-5,08 (Phoenix Contact, or compatible)

4 Transportation / Storage / Scope of delivery
-
18
-
Doc
-
ID: 122515
-
02
WP
-
284
-
x