IEI Technology IKARPC-W10A User manual

IKARPC-W10A-BT In-vehicle Panel PC
Page I
User Manual
MODEL:
IKARPC-W10A-BT
10.1” In-
V
ehicle Panel PC with Touchscreen,
Intel® AtomProcessor E3826, OBD-II, GPS, USB 2.0/3.0,
HDMI, RS-232/422/485, RoHS Compliant, IP 64 Front Panel
Rev. 1.03 – February 7, 2017

IKARPC-W10A-BT In-vehicle Panel PC
Page II
Revision
Date Version Changes
February 7, 2017 1.03 Updated power cable part number and image
Added HDD/SSD installation instruction (Section 3.5)
July 27, 2016 1.02 Updated Section 4.3: Mobile AP
July 23, 2015 1.01 Added a SD card compatibility issue notice.
April 28, 2015 1.00 Initial release

IKARPC-W10A-BT In-vehicle Panel PC
Page III
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

IKARPC-W10A-BT In-vehicle Panel PC
Page IV
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any
directions or instructions contained therein can help avoid making
mistakes.
HOT SURFACE
This symbol indicates a hot surface that should not be touched without
taking care.

IKARPC-W10A-BT In-vehicle Panel PC
Page V
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 FEATURES................................................................................................................... 2
1.3 FRONT PANEL............................................................................................................. 3
1.3.1 LED Indicators................................................................................................... 4
1.4 REAR PANEL............................................................................................................... 5
1.5 BOTTOM PANEL.......................................................................................................... 5
1.6 RIGHT SIDE PANEL ..................................................................................................... 6
1.7 TOP PANEL ................................................................................................................. 7
1.8 SYSTEM SPECIFICATIONS............................................................................................ 7
1.9 DIMENSIONS............................................................................................................. 10
2 UNPACKING................................................................................................................11
2.1 PACKING LIST........................................................................................................... 12
2.2 OPTIONAL ITEMS...................................................................................................... 13
3 INSTALLATION ......................................................................................................... 16
3.1ANTI-STATIC PRECAUTIONS...................................................................................... 17
3.2 INSTALLATION PRECAUTIONS................................................................................... 17
3.3 SD CARD INSTALLATION.......................................................................................... 18
3.4 SIM CARD INSTALLATION........................................................................................ 19
3.5 HDD/SSD INSTALLATION ........................................................................................ 20
3.6 MOUNTING THE SYSTEM .......................................................................................... 24
3.7 EXTERNAL I/O CONNECTORS ................................................................................... 25
3.7.1 COM Port Connection..................................................................................... 25
3.7.2 GPIO and RS-422/485 Connection.................................................................. 26
3.7.3 OBD-II Connection.......................................................................................... 27
3.7.4 Power Input Connection.................................................................................. 29
3.8 POWER-ON PROCEDURE........................................................................................... 30
3.8.1 Power State ...................................................................................................... 31
3.9 SYSTEM MAINTENANCE........................................................................................... 31

IKARPC-W10A-BT In-vehicle Panel PC
Page VI
4 SOFTWARE DRIVERS.............................................................................................. 32
4.1 UTILITY CDAUTO RUN ........................................................................................... 33
4.2 DRIVERS................................................................................................................... 34
4.3 MOBILE AP.............................................................................................................. 36
4.3.1 Installation....................................................................................................... 36
4.3.2 Usage ............................................................................................................... 37
5 BIOS.............................................................................................................................. 39
5.1 INTRODUCTION......................................................................................................... 40
5.1.1 Starting Setup................................................................................................... 40
5.1.2 Using Setup...................................................................................................... 40
5.1.3 Getting Help..................................................................................................... 41
5.1.4 BIOS Menu Bar................................................................................................ 41
5.2 MAIN........................................................................................................................ 42
5.3ADVANCED............................................................................................................... 44
5.3.1 ACPI Settings................................................................................................... 45
5.3.2 Super IO Configuration ................................................................................... 46
5.3.2.1 Serial Port n Configuration....................................................................... 46
5.3.3 Hardware Monitor........................................................................................... 50
5.3.4 Power Management......................................................................................... 51
5.3.5 SMS/RTC Wake Settings................................................................................... 53
5.3.6 Serial Port Console Redirection ...................................................................... 54
5.3.7 CPU Configuration.......................................................................................... 57
5.3.8 IDE Configuration........................................................................................... 59
5.3.9 USB Configuration........................................................................................... 60
5.4 CHIPSET ................................................................................................................... 61
5.4.1 North Bridge Configuration............................................................................. 62
5.4.1.1 Intel IGD Configuration............................................................................ 63
5.4.2 South Bridge Configuration............................................................................. 64
5.5 SECURITY................................................................................................................. 65
5.6 BOOT........................................................................................................................ 66
5.7 SAVE &EXIT............................................................................................................ 68
6 INTERFACE CONNECTORS................................................................................... 70
6.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 71

IKARPC-W10A-BT In-vehicle Panel PC
Page VII
6.2 INTERNAL PERIPHERAL CONNECTORS...................................................................... 72
6.2.1 Battery Connector (BT1).................................................................................. 73
6.2.2 BIOS Flash Connector (JSPI1)........................................................................ 73
6.2.3 Camera Connector (WEB1)............................................................................. 73
6.2.4 Clear CMOS Connector (C_CMOS1) ............................................................. 74
6.2.5 Debug Port Connector (DBG_PORT1)........................................................... 74
6.2.6 LED Connector (JLED1)................................................................................. 74
6.2.7 LVDS Connector (LVDS1)............................................................................... 75
6.2.8 Microphone Connector (JMIC1) ..................................................................... 76
6.2.9 PCIe Mini Socket for 3.75G Module (MINI_PCIE1) ...................................... 76
6.2.10 PCIe Mini Socket for Wireless Module (MINI_PCIE2)................................. 77
6.2.11 PCIe Mini Socket (MINI_PCIE3) .................................................................. 78
6.2.12 Programming Connector (JMCU1)............................................................... 79
6.2.13 Programming Connector (JOBD1)................................................................ 79
6.2.14 Speaker Connector (JSP1)............................................................................. 79
6.2.15 Touch Panel Connector (TOUCH1)............................................................... 80
A REGULATORY COMPLIANCE.............................................................................. 81
B SAFETY PRECAUTIONS......................................................................................... 86
B.1 SAFETY PRECAUTIONS............................................................................................. 87
B.1.1 General Safety Precautions............................................................................. 87
B.1.2 Anti-static Precautions .................................................................................... 88
B.1.3 Product Disposal............................................................................................. 89
B.2 MAINTENANCE AND CLEANING PRECAUTIONS ........................................................ 90
B.2.1 Maintenance and Cleaning.............................................................................. 90
B.2.2 Cleaning Tools................................................................................................. 90
C OBD-II READER COMMAND ................................................................................ 92
C.1 SELECT A CHIP INITIAL MODE:UPDATE F/WOR RUN F/W.................................... 93
C.2 BOOT MODE ............................................................................................................ 93
C.3 RUN MODE.............................................................................................................. 93
C.4 INTO CAN_STANDARD V2.2.B (CAN STANDARD).................................................. 95
C.5 INTO TELEMATICS (VEHICEL INFORMATION) ........................................................... 97
D WATCHDOG TIMER .............................................................................................. 101

IKARPC-W10A-BT In-vehicle Panel PC
Page VIII
E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 104

IKARPC-W10A-BT In-vehicle Panel PC
Page IX
List of Figures
Figure 1-1: IKARPC-W10A-BT Panel PC ......................................................................................2
Figure 1-2: Front View....................................................................................................................3
Figure 1-3: LED Indicators.............................................................................................................4
Figure 1-4: Rear Panel....................................................................................................................5
Figure 1-5: Bottom View ................................................................................................................6
Figure 1-6: Right Side Panel..........................................................................................................6
Figure 1-7: Top Panel.....................................................................................................................7
Figure 1-8: Dimensions (unit: mm).............................................................................................10
Figure 3-1: I/O Cover of the Side Panel......................................................................................18
Figure 3-2: Install SD Card...........................................................................................................18
Figure 3-3: SIM Card Slot Access Panel Retention Screws.....................................................19
Figure 3-4: Install SIM Card.........................................................................................................20
Figure 3-5: Back Cover Retention Screws.................................................................................21
Figure 3-6: HDD Holder Bracket Retention Screw ....................................................................22
Figure 3-7: HDD Installation ........................................................................................................23
Figure 3-8: Secure HDD with Holder Bracket ............................................................................23
Figure 3-9: VESA Mount Retention Screw Holes ......................................................................24
Figure 3-10: RS-232 Connector (COM1, COM2).........................................................................25
Figure 3-11: GPIO and RS-422/485 Connector ..........................................................................26
Figure 3-12: OBD-II Connector....................................................................................................27
Figure 3-13: OBD-II Cable and J1939/FMS Cable......................................................................28
Figure 3-14: OBD-II Connector Pinouts......................................................................................28
Figure 3-15: J1939/FMS Connector Pinouts ..............................................................................28
Figure 3-16: Power Input Connector...........................................................................................29
Figure 3-17: ACC Power Cable....................................................................................................29
Figure 3-18: Optional Cigarette Lighter Cable...........................................................................30
Figure 4-1: Utility CD Menu..........................................................................................................34
Figure 4-2: Mobile AP–Connection.............................................................................................37
Figure 4-3: Mobile AP–Dial Up ....................................................................................................38
Figure 6-1: Main Board Layout Diagram (Front Side)...............................................................71

IKARPC-W10A-BT In-vehicle Panel PC
Page X
Figure 6-2: Main Board Layout Diagram (Solder Side).............................................................71

IKARPC-W10A-BT In-vehicle Panel PC
Page XI
List of Tables
Table 1-1: LED Indicators ..............................................................................................................4
Table 1-2: Technical Specifications..............................................................................................9
Table 2-1: Packing List.................................................................................................................13
Table 2-2: Optional Items.............................................................................................................15
Table 3-1: RS-232 Connector Pinouts ........................................................................................25
Table 3-2: GPIO and RS-422/485 Connector Pinouts................................................................26
Table 3-3: OBD-II Connector Pinouts .........................................................................................27
Table 3-4: Power Input Connector Pinouts................................................................................29
Table 3-5: Power State and Ignition System..............................................................................31
Table 5-1: BIOS Navigation Keys................................................................................................41
Table 6-1: Peripheral Interface Connectors...............................................................................73
Table 6-2: Battery Connector (BT1) Pinouts..............................................................................73
Table 6-3: BIOS Flash Connector (JSPI1) Pinouts....................................................................73
Table 6-4: Camera Connector (WEB1) Pinouts .........................................................................73
Table 6-5: Clear CMOS Connector (C_CMOS1) Pinouts...........................................................74
Table 6-6: Debug Port Connector (DBG_PORT1) Pinouts........................................................74
Table 6-7: LED Connector (JLED1) Pinouts...............................................................................75
Table 6-8: LVDS Connector (LVDS1) Pinouts............................................................................75
Table 6-9: Microphone Connector (JMIC1) Pinouts..................................................................76
Table 6-10: PCIe Mini Socket for 3.75G Module (MINI_PCIE1) Pinouts...................................77
Table 6-11: PCIe Mini Socket for Wireless Module (MINI_PCIE2) Pinouts..............................78
Table 6-12: PCIe Mini Socket (MINI_PCIE3) Pinouts.................................................................79
Table 6-13: Programming Connector (JMCU1) Pinouts ...........................................................79
Table 6-14: Programming Connector (JOBD1) Pinouts............................................................79
Table 6-15: Speaker Connector (JSP1) Pinouts........................................................................79
Table 6-16: Touch Panel Connector (TOUCH1) Pinouts...........................................................80

IKARPC-W10A-BT In-vehicle Panel PC
Page 1
Chapter
1
1 Introduction

IKARPC-W10A-BT In-vehicle Panel PC
Page 2
1.1 Overview
Figure 1-1: IKARPC-W10A-BT Panel PC
The IKARPC-W10A-BT is a 10.1” panel PC designed for in-car use. At the heart of the
system is the Intel® Atomprocessor E3826, offering low power in a powerful package.
The system also offers a multimedia experience with a built-in 2-megapixel camera, HDMI
port, speaker, line-in jack and mic-in jack. The OBD-II connection and GPS functionality
make the IKARPC-W10A-BT an ideal system for in-vehicle applications.
Two serial ports, one GPIO and RS-422/485 port, one external USB 3.0 port, and one
external USB 2.0 port ensure simplified connectivity to a variety of external peripheral
devices. Optional wireless networking capabilities include 802.11b/g/n Wi-Fi, 3.75G, and
Bluetooth 2.1.
1.2 Features
The IKARPC-W10A-BT features the following:
Projected capacitive touchscreen
Intel® Atom® processor E3826 (dual-core, 1.46 GHz, 7 W TDP)
Pre-installed 2.0 GB DDR3 SDRAM memory
Support OBD-II, CAN-bus and digital I/O
GPS functionality with external antenna connector
2-megapixel front-facing camera and speaker

IKARPC-W10A-BT In-vehicle Panel PC
Page 3
Two RS-232 ports and one RS-422/485 port
Optional 802.11b/g/n wireless connection
Optional 3.75G connectivity with dual SIM and an external antenna
Optional Bluetooth 2.1
IP 64 compliant front panel
RoHS compliance
1.3 Front Panel
The front of the IKARPC-W10A-BT is a flat panel screen with a plastic frame. The
components on the front panel are listed below:
2-megapixel camera
Ambient light sensor
LED indicators (see Section 1.3.1)
Figure 1-2: Front View
NOTE:
The automatic screen-dimming function is controlled by the BIOS
option. To enable or disable the function, please refer to Section
5.4.1.1 (LVDS AUTO DIMMING Control option).

IKARPC-W10A-BT In-vehicle Panel PC
Page 4
1.3.1 LED Indicators
The LED indicators on the front panel show the status of power, HDD, Wi-Fi and
GPRS/HSUPA connection.
Figure 1-3: LED Indicators
Red The system is off with power connected
Blue The system is turned on
At regular intervals: low voltage warning
(configured by BIOS option: Section 5.3.4)
Power LED
Blinking At irregular intervals (long-short-short):
GPS antenna is not connected.
Off Wi-Fi is not connected
Wi-Fi LED Green Wi-Fi is connected
Off HDD is not active
HDD LED Blinking HDD is active
Green SIM1 is used for 3.75G connection
3.75G LED Red SIM2 is used for 3.75G connection
Table 1-1: LED Indicators

IKARPC-W10A-BT In-vehicle Panel PC
Page 5
1.4 Rear Panel
The rear panel has VESA mounting screw holes and a 2 W speaker. It also contains a SIM
card slot access panel.
Figure 1-4: Rear Panel
1.5 Bottom Panel
The following I/O connectors can be found on the bottom panel:
1 x 9 V–30 V power input connector
1 x GbE LAN connector
1 x HDMI port
1 x OBD-II/CAN-bus connector
2 x RS-232 serial ports
1 x RS-422/485 serial port and GPIO
1 x USB 3.0 connector
1 x GPS antenna connector
1 x 3.75G antenna connector (optional)

IKARPC-W10A-BT In-vehicle Panel PC
Page 6
Figure 1-5: Bottom View
1.6 Right Side Panel
The right side panel provides access to the following I/O connectors:
1 x Audio line-out jack
1 x Audio mic-in jack
1 x USB 2.0 connector
1 x SD card slot
Figure 1-6: Right Side Panel

IKARPC-W10A-BT In-vehicle Panel PC
Page 7
1.7 Top Panel
The top panel has a power button. Press the power button for 4–6 seconds to power
on/off the system.
Figure 1-7: Top Panel
1.8 System Specifications
The technical specifications for the IKARPC-W10A-BT systems are listed in Table 1-2.
System
CPU Intel® Atom™ processor E3826 (dual-core, 1.46 GHz, 7W TDP)
Memory Pre-installed 2 GB DDR3 SDRAM memory
Audio One 2 W speaker
Camera 2-megapixel front-facing camera
Watchdog Timer Software programmable supports 1~255 sec. system reset
Real-time Clock Battery backup RTC
Storage
SD Card One SD card slot (SD 2.0 compatible, max. 32 GB)
HDD One on-board SATA 3Gb/s connector supports 2.5” flash disk
Display
LCD 10.1” TFT LCD with LED backlight
Max. Resolution 1280 x 800 (WXGA)
Brightness (cd/m2) 350
Contrast Ratio 800:1
Pixel Pitch (mm) 0.0565 (W) x 0.1695 (H)
Viewing Angle 150 (H)/ 145 (V)
Touchscreen Projected capacitive touchscreen with USB interface

IKARPC-W10A-BT In-vehicle Panel PC
Page 8
Auto-dimming Ambient light sensor on the front panel
Communication
LAN 1 x 10/100/100 Mbps RJ-45 (PCIe GbE RTL8111E)
GPS Built-in u-blox LEA-6S GPS module with external antenna connector
Wireless LAN (Optional) 802.11b/g/n 1T1R PCIe Mini Wi-Fi module
Bluetooth (Optional) Bluetooth 2.1 (combo with WWAN)
WWAN (Optional) Optional u-blox LISA-U200 3.75G UMTS/HSPA+ module supports:
HSPA/UMTS-800/850/1900/2100 MHz
Quad-band EDGE/GPRS/GSM-850/900/1800/1900MHz
Power
Power Input 4-pin (2x2) Molex power connector supports DC or ACC power
DC Power 9 V ~ 30 V DC input via optional cigarette lighter power cable
ACC Power ACC power on/off mode with software configurable delay time
Physical Character
Construction Material ABS + PC plastic
Mounting VESA 100 mm x 100 mm
Dimensions (W x H x D) 277 mm x 186 mm x 27 mm
Operation Temperature -10°C ~ 60°C with air flow
Storage Temperature -20°C ~ 70°C
Humidity 5% ~ 95%, non-condensing
Weight (Net/Gross) 1.3 kg/2.2 kg
Operating Shock Half-sine wave shock 5 G, 11 ms, 3 shocks per axis
Operating Vibration MIL-STD-810G 514.6C-1 (with SSD)
IP Level IP 64 compliant front panel
Certifications CE, FCC, e-MARK
Connectors and Buttons
Antenna Connectors 1 x GPS antenna SMA female connector
1 x 3.75G antenna SMA female connector (optional)
Expansion Slot 2 x SIM card slots
2 x Full-size PCIe Mini card slot (one is reserved for 3.75G module)
1 x Half-size PCIe Mini card slot (reserved for Wireless LAN module)
I/O Connector Bottom Panel:
1 x 9 V~ 30 V DC input connector
1 x 10/100/1000 Mbps LAN