GrowMax Water MAXQUARIUM 000PPM User manual

MAXQUARIUM 000PPM
Ultra- ure Reverse Osmosis/Deionization
Water System Up to 500 L/D of ure Water
GROWMAX WATER
™
U l t r a - P u r e W a t e r f o r A q u a r i u m s
ATER SYSTEMS FOR AQUAPONICS
Don't forget to register your system online
and obtain your 2 year warranty at:
www.GrowmaxWater.com
• ENGLISH

Description:
The Maxquarium 000 PPM is a Reverse Osmosis + De-ionization Water System
optimized for aquarium, hydroponic and aquaponic uses. Eliminates up to 99%
of chlorine and reduces sediment down to 5 microns. Also eliminates up to 100%
of all salts and heavy metals, providing 000 ppm pure water. This system is built
to give maximum amount of flow from the membrane. Please read the following
setup and maintenance guide to get the maximum results from your system.
ENGLISH
System Includes:

1
10
2
4
7
6
5
9
3
8
1. Main unit
2. Inlet tubing
3. Sediment filter
4. Green coconut carbon filter
5. Reverse osmosis membrane
6. Pressure gauge
7. De-ionization filter
8. Outlet tubing
9. Shut-off valve
10. Inlet Connectors
1. Membrane Housing
2. Purified Water Line
3. Waste Water Line (Black)
4. Automatic Shut-off Valve
5. Flow Restrictor
Note:
Do not install the unit where the source/inlet pressure may e more than 80 psi
(5 kg/cm2) or there are excessive water hammer/spike pro lems. If your inlet
pressure is more than 80 psi, install a pressure regulator, availa le at your
Grow Max Water dealer or your local hardware store.
Protect unit again t freezing.
System Set Up:
1
235
4

How to Connect and Disconnect
Tubing to Quick Connect Fittings:
Push tube firmly into the fitting connector all the way to until the tube stops.
Try to pull the tube out to check the security. If the tube pulls out, then push
all the way in again.
To disconnect the tubing. First make sure the system is de-pressurized by
turning off inlet water. Push in the "collet" that holds the tube into the fitting
connector. While pushing in the collet you can now simply pull out the tubing.
Push in Collet
Remove Tube
Initial Set Up:
Depending where you want to install the system, you have the option
of using one of the three inlet connectors included in the system.
1. Push in the 3/8" white inlet tubing into the 3/8” fitting on the filter housing
on the right side of the system.
2. Connect the 1/4” blue purified water tubing to the outlet of the Automatic
Shut-off valve.
3. Connect the 1/4” black waste water tubing to the outlet of the flow restrictor.
You are now ready to connect the other end of the 3/8" inlet tubing to your inlet
water connector.
Upon initial start up of system, slowly turn the source water on until the carbon,
sediment, and deionization filters have water in the housings. Next, open source
water up all the way (do not exceed 80 psi). Flush the system for 15 minutes
when the system is new and/or when you replace your membrane.
Note:
It may take up to 24 hours of running the system for the PPM & pH of the
purified water to sta ilize.

Filter Changes & Recommended Maintenance:
RE LACEMENT SCHEDULE:
150 GPD membrane element -6 Months to 2 years.
Carbon Filter 10 x 2.5” -Change every 4 -6 months or as needed.
Sediment Filter 10” x 2.5” - Change every 4 -6 months or as needed.
De-ionization Filter 10" x 2.5" - Change as needed depending on your water quality needs.
atch our Videos on www.Growmax ater.com
• How to change the RO Membrane • How to change the filters
• How to use the quick fittings
Replacements:
Replacements are available at your Growmax Water dealer or at:
www.GrowmaxWater.com
OWER GROW 500 Replacement arts
MAXQUARIUM 000 M Replacement arts
Important Information
& Performance Parameters:
The flow of purified water is determined by the GPD rating of the membrane, inlet
pressure, inlet temperature, and inlet PPM. The MAXQUARIUM Reverse
Osmosis system has the capacity to produce up to 150 gpd (500 liters per day).
The parameters for optimum operation are: Water temperature 25ºC, Inlet water
pressure 3 to 5 kg/cm2 and water quality of 550 ppm or less.
You will notice in colder areas or in the winter, when water temperatures
are lower, that the flow rate will be slower. If your inlet pressure is less than
60 psi, you may experience less than the rated 150 GPD flow rate. A minimum
of 40 psi is required to properly operate the system. The higher the inlet pressure,
the better the flow. A booster pump kit is available as an option in case of low
pressure and is necessary if your pressure is below 40 psi.
The RO membranes included with the filter can handle water up to 1000 PPM and
with a hardness of 170 PPM or 20º hf of hardness. Note that this is considered both
very contaminated and very hard water and may shorten the life of your membrane.
Note:
The first minute of RO water produced are higher in PPM than after the system
has run a few minutes.

arranty:
A one year warranty comes with each system and protects against
manufacturer defects on all components. The warranty does not include
obstructed filters due to lack of regular maintenance of due to excessive
sediment, chlorine, iron, silica, manganese, or sulphur in your water. The
warranty also does not include damage to the unit from use outside of
normal grow and garden installation parameters.
lease see below how to ADD an
EXTRA ONE YEAR to your WARRANTY.
Technical Support and Contact: ENGLISH ONLY.
If you have a particular application or setup question, please contact
Growmax Water IN ENGLISH ONLY direct at:
[e-mail]
*Register your product online
to obtain your 2 YEAR
product warranty!
www.Growmax ater.com
Optional Accessories:
Kills 100% of all bacteria
and viruses. Ensures the
safest water.
UV Sterilizer Kit
This de-ionization filter is designed to serve as a post-polishing
stage for any Reverse Osmosis system delivering ultra pure
000 PPM water.
De-Ionization Kit
Fill any tank or
reservoir unattended.
Float Valve Kit
Recommended for low inlet
pressure under 40 PSI
(3kg/cm2). Boosts pressure
to 60+ PSI (4kg/cm2).
Easy connection.
Booster ump Kit