Panasonic Circuit Protector Elements UNHZ204 User manual

This product complies with the RoHS Directive (EU 2002/95/EC).
Circuit Protector Elements
1
Publication date: November 2006 SQB00037BED
UNHZ204
Circuit Protector Elements
For overcurrent protection
■Features
•Sharp cutoff characteristics and low voltage drop
•Flame retardant package and low heat generation, high density
mounting is possible.
■Absolute Maximum Ratings Ta=25°C
Parameter Symbol Rating Unit
Operating ambient temperature Topr −55 to +125 °C
Storage temperature Tstg −55 to +125 °C
■Usage Notes
•Package shall be overheated and dangerous for overcurrent.
•This device should be used only to the secondary circuit.
Package will be damaged for added overpower.
•This device is not electrical fuse legally. Please draw a clear line between electrical fuse from this device.
Parameter Min Typ Max Unit
Rated voltage 50 V
Rated current 1.5 A
Internal Resistance 27 35 43 mΩ
Cutoff current *3.0 A
■Electrical Characteristics Ta=25°C ±3°C
Note) *: Measurement condition of cutoff current shall be at Ta=25°C, t =1 s
Tolerance of cutoff current shall be ±20%
Marking Symbol: H4
Unit: mm
SMini2-F1 Package
5˚
5˚
1.25
±0.1 0.7 ±0.1
2.5
±0.2
1.7
±0.1
0.4
±0.1
0 to 0.1
(0.15)
0.16
0.5
±0.1
1
2
+0.1
–0.06
0.35 ±0.1
0 to 0.1
2
1
Lead Connection

This product complies with the RoHS Directive (EU 2002/95/EC).
UNHZ204
2SQB00037BED
−25 150250 100 12550 75
0.6
1.1
1.0
0.9
0.8
0.7
Cutoff current ratio
Ambient temperature T
a
(°C)
Cutoff current ratio TaI2t t
Cutoff current characteristics
10 10
2
10
3
1
1
10
10
2
10
3
10
4
T
a
= 25°C
Cutoff line of real ability by pulse
Limit line of real ability by pulse
Recommendable limit line by pulse
t (ms)
I
2
t (A
2
•ms)
0642
10
−3
1
10
−1
10
−2
+20%−20%
T
a
= 25°C
Cutoff current (A)
Cutoff time t (s)

Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
–Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
–Any applications other than the standard applications intended.
(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
 Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.