Gulfstream G450-8 Technical manual

G450-8 Massage chair
Configure: 9640 Model chair

Thank you for purchasing this product.
In order to achieve maximum benefit and safety while using the model 9640 chair,
please read and follow this manual carefully before operating this product.
Please pay particular attention to important safety instructions, indicators and
warnings within.
Keep this manual handy for future reference.
Note: The manufacturer reserves the right to revise chair design and description
without further notice.

Power-down after each use!
servicing
immersed in
keep vents clear
must use gfci class A.
Employing class A ground fault circuit interrupter.

doit utiliser la
classe GFCI A.

3.Fasten chair frame to platform using hardware provided, as per illustration above.
Ensure base fastened securely.
Push rod connectors
Air connector
Compressor
connector
Match numbers on
hose connections
4.To ensure connections for aircompressor and valvesare properly madeas
well as connectionsfor back incline/recline& forward/backward actuators
have been properlymade, test controller functions priorto use.

Program duration
In automatic mode, a selection of three massage-type combinations are available:
Whole body, shoulder and neck and back and waist. In manual mode, a
In manual mode, a selection of three massage functions are available: overall,
fixed and partial area.
With fixed , the massage hands can be moved up or down realtime. Each
massage function has five levels speed options; the width between the two massage
hands can be adjusted three wide, medium and narrow when it is under
flapping, shiatsu or knocking state.
Equipped with 5airbags with four air pressure modes and two strengths.
Seat moves forward/backward and inclines/reclines.
Massage hands return to original position when chair is powered-down.
levels of
Improve
muscles.

3 duration levels 10 mins,20 mins
and 30mins.
Automatic massage programs
Carry on automatic massage
around in carrying thelower
back/waist mainly
Central
of two levels.

Forward
Backward
Incline
recline
movement
Press and hold this button, the chair will move
forward, to stop release your finger.
Press and hold this button, the chair will move
upward, to stop release your finger.
Press and hold this button, the chair will move
backward, to stop release your finger.
Press and hold this button, the chair will move
downward, to stop release your finger.
Movement will stopwhen piston reaches maximum/minimum extention aswell.
2. Component installationinstructions.
1.Align backrestsupport shafts with backrest support seats. Drop-in to engage
locking hook (see fig 1).
2.Lay back backrest andalign electric cylinderbolt with backrest electric
cylinder support andengage backrest electric cylinder support locking
hook (See fig2).
1. Fig 2, disengage #6 & pull backrest forward.
2. Fig 1, lift #3 (both side) & pull backrest up.
#1 support seats
#2 Supporting shaft of the Backrest
#3 Backrest support seats self Locking hook
#4 Electric cylinder bolt
#5 Backrest electric cylinder support
#6 Baxkrest electric cylinder support self locking hook
NOTE: Ensure cylinder connecters are disengaged.
Backrest

1 1 & 2 fasten rectangular L racket (plate) with bolts provided.
2 Put the screws into the rectangular plate.
3 Once rectangular plate is fixed to the frame; the next step is to install the armrests
4 Bolts go through bottom-rear of armrest bracket, then secured with nuts.
5 The seat frame and armrest installation is finished.
POWER-UP
POWER-DOWN
stop power oncontroller
5.To adjust the back simultaneously
Press and hold button to recline/ button to incline. See table page.10
for controller function.
WARNING:DO NOTEXERTANY PRESSUREOTHER THANYOUR OWNWEIGHT
ON THEBACK WHILE ITIS RISING.
Hook & loop ribbon

See table page.10 for controller function.
Name: G450-8 Massage chair
Configure: 9640 Model chair