H3C S3610 Series User manual

H3C S3610 Series Ethernet Switches
Quick Start
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08225A-20080526-C-1.07

Copyright © 2006-2008, Hangzhou H3C Technologies Co.,
Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of Hangzhou H3C
Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF,
NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,
Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT, XGbus,
N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners.
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of
any kind, express or implied.
To obtain the latest information, please access:
http://www.h3c.com
Technical Support
customer_servic[email protected]
http://www.h3c.com

About This Manual
Related Documentation
In addition to this manual, each H3C S3610 Series Ethernet
Switches documentation set includes the following:
Manual Content
H3C S3610&S5510 Series
Ethernet Switches Operation
Manual
It is used for assisting the users
in data configurations and
typical applications
H3C S3610&S5510 Series
Ethernet Switches Command
Manual
It is used for assisting the users
in using various commands.
H3C S3610 Series Ethernet
Switches Installation Manual
It is used for assisting the users
in switch installation, booting up,
hardware and software
maintenance.
Organization
H3C S3610 Series Ethernet Switches Quick Start is organized as
follows:
Chapter Contents
1 Product Overview Introduces the characteristics and technical specifications of S3610 Series Ethernet
Switches.

Chapter Contents
2 Installation
Preparation
Introduces the installation preparation and
precaution of S3610 Series Ethernet
Switches.
3 Installing the
Switch
Introduces the procedures to install an
S3610 Series Ethernet Switch, including the
setup of the mainframe, cards and cables.
4 Lightning
Protection of the
Switch
Introduces lightning protection of S3610
Series Ethernet Switches.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in
Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square
brackets [ ] are optional.
{ x | y | ... }
Alternative items are grouped in braces
and separated by vertical bars. One is
selected.
[ x | y | ... ]
Optional alternative items are grouped in
square brackets and separated by vertical
bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces
and separated by vertical bars. A minimum
of one or a maximum of all can be selected.

Convention Description
[ x | y | ... ] *
Optional alternative items are grouped in
square brackets and separated by vertical
bars. Many or none can be selected.
&<1-n> The argument(s) before the ampersand (&)
sign can be entered 1 to n times.
# A line starting with the # sign is comments.
II. GUI conventions
Convention Description
< > Button names are inside angle brackets.
For example, click <OK>.
[ ]
Window names, menu items, data table
and field names are inside square
brackets. For example, pop up the [New
User] window.
/ Multi-level menus are separated by forward
slashes. For example, [File/Create/Folder].
III. Symbols
Convention Description
Warning Means reader be extremely careful.
Improper operation may cause bodily
injury.
Caution
Means reader be careful. Improper
operation may cause data loss or damage
to equipment.
Note Means a complementary description.

Environmental Protection
This product has been designed to comply with the requirements
on environmental protection. For the proper storage, use and disposal
of this product, national laws and regulations must be observed.

Quick Start
H3C S3610 Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................1-1
1.1 Introduction ........................................................................1-1
1.2 S3610-28TP Ethernet Switch.............................................1-3
1.2.1 Front Panel ..............................................................1-3
1.2.2 Rear Panel...............................................................1-4
1.2.3 Power Supply System .............................................1-4
1.2.4 Cooling System .......................................................1-5
1.3 S3610-28P Ethernet Switch...............................................1-5
1.3.1 Front Panel ..............................................................1-5
1.3.2 Rear Panel...............................................................1-6
1.3.3 Power Supply System .............................................1-6
1.3.4 Cooling System .......................................................1-6
1.4 S3610-28F Ethernet Switch ...............................................1-7
1.4.1 Front Panel ..............................................................1-7
1.4.2 Rear Panel...............................................................1-7
1.4.3 Power Supply System .............................................1-8
1.4.4 Cooling System .......................................................1-8
1.5 S3610-52P Ethernet Switch...............................................1-8
1.5.1 Front Panel ..............................................................1-8
1.5.2 Rear Panel...............................................................1-9
1.5.3 Power Supply System ...........................................1-10
1.5.4 Cooling System .....................................................1-10
1.6 S3610-52M/S3610-52M-DC Ethernet Switch ..................1-10
1.6.1 Front Panel ............................................................1-10
1.6.2 Rear Panel.............................................................1-11

Quick Start
H3C S3610 Series Ethernet Switches Table of Contents
ii
1.6.3 Power Supply System ...........................................1-13
1.6.4 Cooling System .....................................................1-13
1.7 LEDs ................................................................................1-14
1.7.1 LEDs of the S3610-28TP Ethernet switch.............1-14
1.7.2 LEDs of the S3610-28P Ethernet switch...............1-21
1.7.3 LEDs of the S3610-28F Ethernet switch ...............1-26
1.7.4 LEDs of the S3610-52P Ethernet switch...............1-34
1.7.5 LEDs of the S3610-52M/S3610-52M-DC Ethernet
switch..............................................................................1-34
1.8 Specifications of the S3610 Series ..................................1-36
1.9 SFP modules....................................................................1-38
1.9.1 100 Mbps SFP modules ........................................1-38
1.9.2 1000 Mbps SFP modules ......................................1-38
Chapter 2 Installation Preparation...............................................2-1
2.1 Safety Precautions .............................................................2-1
2.2 Installation Site...................................................................2-1
2.2.1 Temperature/Humidity.............................................2-2
2.2.2 Cleanness................................................................2-2
2.2.3 Electromagnetic Susceptibility.................................2-3
2.2.4 Laser Safety ............................................................2-4
2.3 Installation Tools ................................................................2-4
Chapter 3 Installing the Switch....................................................3-1
3.1 Installing a Switch ..............................................................3-1
3.1.1 Cabinet Mounting ....................................................3-1
3.1.2 Desk Mounting.........................................................3-8
3.2 Connecting the Power Cord and the Ground Wire ............3-8
3.2.1 Connecting the AC Power Cord ..............................3-8
3.2.2 Connecting the DC-Input Power Cord...................3-10

Quick Start
H3C S3610 Series Ethernet Switches Table of Contents
iii
3.2.3 Connecting the Ground Wire.................................3-15
3.2.4 Multi-power Input...................................................3-19
3.3 Connecting the Switch to a Console Terminal.................3-20
3.3.1 Console Cable .......................................................3-20
3.3.2 Connecting the Console Cable..............................3-21
3.4 Installation of the Optional Interface Modules..................3-22
3.4.1 Installation of the Optional Interface Modules .......3-22
3.4.2 Removal of Optional Interface Modules ................3-23
3.5 Verifying Installation.........................................................3-24
Chapter 4 Lightning Protection of the Switch ............................4-1
4.1 Installation of Lightning Arrester for AC Power (Socket Strip
with Lightning Protection).........................................................4-1
4.2 Installation of Lightning Arrester for Network Port .............4-4

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-1
Chapter 1 Product Overview
1.1 Introduction
H3C S3610 Series Ethernet Switches (the S3610 series) are
L2/L3 wire speed Ethernet switches developed by Hangzhou H3C
Technologies Co., Ltd. They are intelligent network management
switches intended for networks where high performance, dense port
distribution, and ease of installation are required.
The S3610 series are designed to operate on the convergence
and access layer of intranets and metropolitan area networks (MANs).
They support both IPv4 and IPv6 and thus offer abundant services
and routing functionalities.
Currently, S3610 series contain the following models.
Table 1-1 Models in the S3610 series
Model Power
supply
Total
service
ports
Number
of 100
Mbps
ports
Number
of 1000
Mbps
uplink
ports
Console
port
S3610
-28TP
AC-input
DC-input 28
24 fixed
10Base-
T/100Ba
se-TX
Ethernet
ports
2 × 1000
Mbps SFP
ports
2 ×
10/100/10
00MBase-
T Ethernet
ports
One

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-2
Model Power
supply
Total
service
ports
Number
of 100
Mbps
ports
Number
of 1000
Mbps
uplink
ports
Console
port
S3610
-28P
AC-input
DC-input 28
24 fixed
10Base-
T/100Ba
se-TX
Ethernet
ports
4 × 1000
Mbps SFP
ports
One
S3610
-28F
AC-input
DC-input 28
24 x 100
Mbps
SFP
ports
2 × 1000
Mbps SFP
ports
2 ×
10/100/10
00MBase-
T Ethernet
ports
One
S3610
-52P
AC-input
DC-input 52
48 fixed
10Base-
T/100Ba
se-TX
Ethernet
ports
4 × 1000
Mbps SFP
ports
One

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-3
Model Power
supply
Total
service
ports
Number
of 100
Mbps
ports
Number
of 1000
Mbps
uplink
ports
Console
port
S3610
-52M AC-input One
S3610
-52M-
DC
DC-input
Dependi
ng on
the
inserted
interfac
e
module,
52 at
most.
Dependi
ng on the
inserted
interface
module,
up to 48
10/100
Mbps
electrical
ports or
48 100
Mbps
SFP
ports
4 × 1000
Mbps SFP
ports
4 ×
10/100/10
00 Mbps
electrical
ports One
1.2 S3610-28TP Ethernet Switch
1.2.1 Front Panel
On its front panel the S3610-28TP provides 24 fixed
10Base-T/100Base-TX Ethernet ports, two 1000 Mbps SFP ports, two
10/100/1000Base-T Ethernet ports and one Console port, as shown in
Figure 1-1.

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-4
(1): 100 Mbps Ethernet port status LEDs
(2): 1000 Mbps SFP port status LEDs
(3): 1000 Mbps Ethernet port status LEDs
(4): Console port (5): 7-segment numerical display
(6): Port mode switch button (7): Port mode switch LED
(8): Power LED (9): DC-input power LED
Figure 1-1 Front panel of an S3610-28TP Ethernet switch
1.2.2 Rear Panel
（1）（2）（3）（1）（2）（3）
(1): AC-input power socket
(2): DC-input power socket
(3): Grounding screw
Figure 1-2 Rear panel of an S3610-28TP Ethernet switch
1.2.3 Power Supply System
The S3610-28TP supports power load sharing between the AC
and DC power supply. It can also be powered by the AC power supply
or DC power supply only.

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-5
I. AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz
II. DC input:
Rated voltage range: -48 V to -60 V
Max voltage range: -36 V to -72V
1.2.4 Cooling System
S3610-28TP Ethernet switch provide one fan for heat dissipation.
1.3 S3610-28P Ethernet Switch
1.3.1 Front Panel
On its front panel the S3610-28P provides 24 fixed
auto-negotiation 10Base-T/100Base-TX Ethernet ports, four 1000
Mbps SFP ports and one Console port, as shown in Figure 1-3.
(1): 100 Mbps Ethernet port status LEDs
(2): 1000 Mbps SFP port status LEDs (3): Console port
(4): 7-segment numerical display (5): Port mode switch button
(6): Port mode switch LED (7): Power LED
(8): DC-input power LED

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-6
Figure 1-3 Front panel of the S3610-28P
1.3.2 Rear Panel
（1）（2）（3）（1）（2）（3）
(1): AC-input power socket
(2): DC-input power socket
(3): Grounding screw
Figure 1-4 Rear panel of the S3610-28P
1.3.3 Power Supply System
The S3610-28P supports power load sharing between the AC
and DC power supply. It can also be powered by the AC power supply
or DC power supply only.
I. AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz
II. DC input:
Rated voltage range: -48 V to -60 V
Max voltage range: -36 V to -72V
1.3.4 Cooling System
S3610-28P Ethernet switch provide one fan for heat dissipation.

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-7
1.4 S3610-28F Ethernet Switch
1.4.1 Front Panel
On its front panel the S3610-28F provides 24 x 100 Mbps SFP
ports, two 1000 Mbps SFP ports, two 10/100/1000Base-T Ethernet
ports and one Console port, as shown in Figure 1-5.
(1): 100 Mbps SFP port status LEDs
(2): 1000 Mbps SFP port status LEDs
(3): 1000 Mbps Ethernet port status LEDs
(4): Console port (5): 7-segment numerical display
(6): Port mode switch button (7): Port mode switch LED
(8): Power LED (9): DC-input power LED
Figure 1-5 Front panel of the S3610-28F
1.4.2 Rear Panel
(1) (2) (3) (1) (2) (3)
(1): AC-input power socket (2): DC-input power socket
(3): Grounding screw
Figure 1-6 Rear panel of the S3610-28F Ethernet switch

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-8
1.4.3 Power Supply System
The S3610-28F supports power load sharing between the AC
and DC power supply. It can also be powered by the AC power supply
or DC power supply only.
I. AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz
II. DC input:
Rated voltage range: -48 V to -60 V
Max voltage range: -36 V to -72V
1.4.4 Cooling System
S3610-28F Ethernet switch provide two fans for heat dissipation.
1.5 S3610-52P Ethernet Switch
1.5.1 Front Panel
On its front panel the S3610-52P provides 48 fixed
auto-negotiation 10Base-T/100Base-TX Ethernet ports, four 1000
Mbps SFP ports and one Console port, as shown in Figure 1-7.

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-9
(1): 100 Mbps Ethernet port status LEDs (2): Console port
(3): 7-segment numerical display (4): Port mode switch button
(5): Port mode switch LED (6): Power LED
(7): DC-input power LED
(8): 1000 Mbps SFP port status LEDs
Figure 1-7 Front panel of the S3610-52P
1.5.2 Rear Panel
（1）（2）（3）（1）（2）（3）
(1): AC-input power socket
(2): DC-input power socket
(3): Grounding screw
Figure 1-8 Rear panel of the S3610-52P Ethernet switch

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-10
1.5.3 Power Supply System
The S3610-52P supports power load sharing between the AC
and DC power supply. It can also be powered by the AC power supply
or DC power supply only.
I. AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz
II. DC input:
Rated voltage range: -48 V to -60 V
Max voltage range: -36 V to -72V
1.5.4 Cooling System
S3610-52P Ethernet switch provide one fan for heat dissipation.
1.6 S3610-52M/S3610-52M-DC Ethernet
Switch
1.6.1 Front Panel
On its front panel, the S3610-52M/S3610-52M-DC switch
provides six slots where you can insert the 8-port 100 Mbps
single-mode/multimode modules, 8-port 10Base-T/100Base-TX
modules, and 8-port 100 Mbps SFP modules as needed. The
following figure illustrates the front panel with all the six slots inserted
with 8-port 100 Mbps single-mode modules:

Quick Start
H3C S3610 Series Ethernet Switches Chapter 1 Product Overview
1-11
(1) (2)
(1): Power LED (2): Console port
Figure 1-9 Front panel of the S3610-52M/S3610-52M-DC
Caution:
The interface modules on the front panel of the H3C S3610-52M and
S3610-52M-DC are not hot-swappable. To install or remove these
modules, you must first power off the switch. For how to install and
remove these modules, refer to section 3.4 “Installation of the
Optional Interface Modules”.
1.6.2 Rear Panel
I. Rear panel of the S3610-52M switch
The rear panel of the S3610-52M switch is illustrated by the
following figure. On the rear panel, there are grounding screw,
AC-input power socket, RPS DC-input redundancy power socket, and
the fixed interface module.