H3C S5560S-SI User manual

i
Contents
Preparing for installation················································································1
Safety recommendations ···································································································································4
Examining the installation environment ·············································································································4
Cleanliness·················································································································································6
Corrosive gas limit······································································································································7
Examining the installation site····························································································································7
Checking power distribution or power supply environment················································································8
Laser safety························································································································································9
Installation tools ·················································································································································9
Installing the switch······················································································10
Installing the switch in a 19-inch rack···············································································································11
Mounting brackets····································································································································11
Attaching the mounting brackets to the switch·························································································13
Rack-mounting the switch························································································································15
Mounting the switch on a workbench···············································································································17
Mounting the switch on a wall··························································································································18
Grounding the switch ·······································································································································20
Grounding the switch with a grounding strip····························································································20
Grounding the switch with a grounding conductor buried in the earth ground·········································21
Grounding the switch by using the PE wire of the AC power cord···························································22
Verifying the connection after grounding the switch·················································································22
Installing and removing a power supply···········································································································23
Installing a power supply··························································································································23
Removing a power supply························································································································24
Connecting the power cord······························································································································25
Connecting the AC power cord for the fixed AC power supply································································26
Connecting the DC power cord for the fixed DC power supply································································26
Connecting the power cord for a CA-70A12 or PSR75-12A power supply··············································27
Connecting the DC power cord for a PSR150-D1 power supply ·····························································28
Verifying the installation···································································································································29
Accessing the switch for the first time··························································30
Managing the switch from the GUI···················································································································30
Accessing the GUI ···································································································································30
Changing the default login password·······································································································30
Creating user accounts····························································································································30
Managing the switch from the CLI····················································································································31
Connecting the switch to a configuration terminal····················································································31
Connecting a console cable·····················································································································32
Connecting a micro USB console cable···································································································35
Setting terminal parameters·····················································································································36
Starting the switch····································································································································37
Setting up an IRF fabric···············································································38
IRF fabric setup flowchart ································································································································39
Planning IRF fabric setup·································································································································40
Planning IRF fabric size and the installation site······················································································40
Identifying the master switch and planning IRF member IDs···································································40
Planning IRF topology and connections···································································································40
Identifying IRF physical ports on the member switches···········································································41
Planning the cabling scheme···················································································································43
Configuring basic IRF settings·························································································································44
Connecting the IRF physical ports···················································································································44
Verifying the IRF fabric setup···························································································································44

ii
Maintenance and troubleshooting································································46
Fixed power supply failure ·······························································································································46
Input failure on an AC-powered switch ····································································································46
Input failure on a DC-powered switch······································································································47
Input failure on a DC and AC-powered switch·························································································47
Removable power supply failure······················································································································48
Fan tray failure·················································································································································48
Configuration terminal issues···························································································································48
No display on the configuration terminal··································································································48
Garbled display on the configuration terminal··························································································49

1
Preparing for installation
This document provides an installation guide for the following switch series:
•
S5560S-SI switch series
•
S5130S-SI switch series
•
S5130S-LI switch series
•
S5120V2-SI switch series
•
S5120V2-LI switch series
•
S5110V2-SI switch series
•
S5000V3-EI switch series
•
S5000V5-EI switch series
•
S5500V3-SI switch series
•
S3100V3-SI switch series
Table 1 describes the switch models that each switch series includes.
Table 1 Switch series and models
Switch series Model Product code (PID)
S5560S-SI switch
series Non-PoE models
S5560S-28P-SI LS-5560S-28P-SI
LS-5560S-28P-SI-GL
S5560S-52P-SI LS-5560S-52P-SI
LS-5560S-52P-SI-GL
S5560S-28S-SI LS-5560S-28S-SI
LS-5560S-28S-SI-GL
S5560S-52S-SI LS-5560S-52S-SI
LS-5560S-52S-SI-GL
S5560S-28F-SI LS-5560S-28F-SI
S5560S-28DP-SI LS-5560S-28DP-SI
S5130S-SI switch
series Non-PoE models
S5130S-28S-SI LS-5130S-28S-SI
S5130S-28S-SI-MM LS-5130S-28S-SI-MM
S5130S-28S-SI-SM LS-5130S-28S-SI-SM
S5130S-52S-SI LS-5130S-52S-SI
S5130S-28F-SI LS-5130S-28F-SI
S5130S-LI switch
series
Non-PoE
models
S5130S-28S-LI LS-5130S-28S-LI
LS-5130S-28S-LI-GL
S5130S-28S-LI-MM LS-5130S-28S-LI-MM
S5130S-28S-LI-SM LS-5130S-28S-LI-SM
S5130S-52S-LI LS-5130S-52S-LI
LS-5130S-52S-LI-GL
PoE models S5130S-28S-PWR-LI LS-5130S-28S-PWR-LI

2
Switch series Model Product code (PID)
S5130S-28S-HPWR-LI LS-5130S-28S-HPWR-LI
S5130S-52S-PWR-LI LS-5130S-52S-PWR-LI
S5120V2-SI
switch series Non-PoE models
S5120V2-10P-SI LS-5120V2-10P-SI
S5120V2-28P-SI LS-5120V2-28P-SI
S5120V2-52P-SI LS-5120V2-52P-SI
S5120V2-LI
switch series
Non-PoE
models
S5120V2-10P-LI LS-5120V2-10P-LI
LS-5120V2-10P-LI-GL
S5120V2-20P-LI LS-5120V2-20P-LI
LS-5120V2-20P-LI-GL
S5120V2-28P-LI LS-5120V2-28P-LI
LS-5120V2-28P-LI-GL
S5120V2-52P-LI LS-5120V2-52P-LI
LS-5120V2-52P-LI-GL
PoE models
S5120V2-10P-PWR-LI LS-5120V2-10P-PWR-LI
LS-5120V2-10P-PWR-LI-GL
S5120V2-28P-PWR-LI LS-5120V2-28P-PWR-LI
LS-5120V2-28P-PWR-LI-GL
S5120V2-28P-HPWR-LI LS-5120V2-28P-HPWR-LI
LS-5120V2-28P-HPWR-LI-GL
S5120V2-52P-PWR-LI LS-5120V2-52P-PWR-LI
LS-5120V2-52P-PWR-LI-GL
S5120V2-12TP-HPWR-LI LS-5120V2-12TP-HPWR-LI
S5110V2-SI
switch series Non-PoE models S5110V2-28P-SI LS-5110V2-28P-SI
S5110V2-52P-SI LS-5110V2-52P-SI
S5000V3-EI
switch series
Non-PoE
models
S5016PV3-EI LS-5016PV3-EI
LS-5016PV3-EI-GL
S5024PV3-EI LS-5024PV3-EI
LS-5024PV3-EI-GL
S5048PV3-EI LS-5048PV3-EI
LS-5048PV3-EI-GL
S5024FV3-EI LS-5024FV3-EI
LS-5024FV3-EI-GL
PoE models
S5024PV3-EI-PWR LS-5024PV3-EI-PWR
LS-5024PV3-EI-PWR-GL
S5024PV3-EI-HPWR LS-5024PV3-EI-HPWR
LS-5024PV3-EI-HPWR-GL
S5048PV3-EI-PWR LS-5048PV3-EI-PWR
LS-5048PV3-EI-PWR-GL
S5000V5-EI Non-PoE S5008PV5-EI LS-5008PV5-EI

3
Switch series Model Product code (PID)
switch series
models
LS-5008PV5-EI-H1
S5008PV5-EI-S LS-5008PV5-EI-S-GL
S5016PV5-EI LS-5016PV5-EI
S5016PV5-EI-S LS-5016PV5-EI-S-GL
S5024PV5-EI LS-5024PV5-EI
LS-5024PV5-EI-GL
S5024PV5-EI-S LS-5024PV5-EI-S-GL
S5048PV5-EI LS-5048PV5-EI
LS-5048PV5-EI-GL
PoE models
S5008PV5-EI-HPWR LS-5008PV5-EI-HPWR
LS-5008PV5-EI-HPWR-H1
LS-5008PV5-EI-HPWR-GL
S5008PV5-EI-HPWR-S LS-5008PV5-EI-HPWR-S-GL
S5016PV5-EI-PWR-S LS-5016PV5-EI-PWR-S-GL
S5024PV5-EI-PWR LS-5024PV5-EI-PWR
S5024PV5-EI-PWR-S LS-5024PV5-EI-PWR-S-GL
S5024PV5-EI-HPWR LS-5024PV5-EI-HPWR
LS-5024PV5-EI-HPWR-GL
S5048PV5-EI-PWR LS-5048PV5-EI-PWR
LS-5048PV5-EI-PWR-GL
S5500V3-SI
switch series Non-PoE models
S5500V3-24P-SI LS-5500V3-24P-SI
S5500V3-48P-SI LS-5500V3-48P-SI
S5500V3-28S-SI LS-5500V3-28S-SI
S5500V3-28PS-SI LS-5500V3-28PS-SI
S5500V3-54S-SI LS-5500V3-54S-SI
S5500V3-54PS-SI LS-5500V3-54PS-SI
S5500V3-36F-SI LS-5500V3-36F-SI
S5500V3-28S-DP-SI LS-5500V3-28S-DP-SI
S5500V3-54S-DP-SI LS-5500V3-54S-DP-SI
S5500V3-36F-DP-SI LS-5500V3-36F-DP-SI
S5500V3-54F-DP-SI LS-5500V3-54F-DP-SI
S3100V3-SI
switch series Non-PoE models
S3100V3-10TP-SI LS-3100V3-10TP-SI
LS-3100V3-10TP-SI-H1
S3100V3-18TP-SI LS-3100V3-18TP-SI
LS-3100V3-18TP-SI-H1

4
Switch series Model Product code (PID)
S3100V3-28TP-SI LS-3100V3-28TP-SI
LS-3100V3-28TP-SI-H1
S3100V3-52TP-SI LS-3100V3-52TP-SI
LS-3100V3-52TP-SI-H1
PoE models
S3100V3-10TP-PWR-SI LS-3100V3-10TP-PWR-SI
LS-3100V3-10TP-PWR-SI-H1
S3100V3-20TP-PWR-SI LS-3100V3-20TP-PWR-SI
LS-3100V3-20TP-PWR-SI-H1
S3100V3-28TP-PWR-SI LS-3100V3-28TP-PWR-SI
LS-3100V3-28TP-PWR-SI-H1
NOTE:
Switches of the same model but different PIDs might differ in
hardware and software features.
You
can view the PID of a switch on the label located on its rear panel or top panel.
Safety recommendations
To avoid equipment damage or bodily injury, read the following safety recommendations before
installation. Note that the recommendations do not cover every possible hazardous condition.
•
Before cleaning the switch, remove all power cords from the switch. Do not clean the switch
with wet cloth or liquid.
•
Do not place the switch near water or in a damp environment. Prevent water or moisture from
entering the switch chassis.
•
Do not place the switch on an unstable case or desk. The switch might be severely damaged in
case of a fall.
•
Ensure good ventilation at the installation site and keep the air inlet and outlet vents of the
switch free of obstruction.
•
Make sure the operating voltage is as required.
•
To avoid electrical shocks, do not open the chassis while the switch is operating or when the
switch is just powered off.
•
Always wear an ESD wrist strap when installing the switch. Make sure the strap makes good
skin contact and is reliably grounded.
Examining the installation environment
To ensure correct operation of your switch, make sure the installation environment meets the
requirements listed in Table 2.
Table 2 Checking list for the installation environment
Item Requirements
Ventilation and heat dissipation
CAUTION:
To ensure correct operation of your device, make sure the installation
environment is adequately ventilated to prevent the switch from
overheating.

5
Item Requirements
•Ensure a minimum clearance of 10 cm (3.94 in) around the chassis.
•Do not install the device near a heat source, for example, a stove or
heater.
•Ensure air ventilation in the installation environment.
•Do not block the ventilation holes in the device or power adapter.
Anti-moisture
CAUTION:
Water or moisture might damage the circuits of the device.
•Do not place the device near water or in a damp environment.
•Install the switch in a clean, dry, and ventilated place where
temperature is controlled in a stable range.
•Make sure the installationenvironment is free from water leakage or
condensation. If required, install a dehumidification device (such as
an air conditioner with a dehumidification function or a dedicated
dehumidifier).
•Do not operate the device under or near the water source, such as
the wash basin, laundry room, or areas with high humidity.
•Do not touch the device with wet hands.
Temperature/humidity
For correct operation and long service life of your switch, maintain the
temperature and humidity in the equipment room at acceptable ranges.
•Lasting high relative humidity can cause poor insulation, electricity
leakage, mechanical property change of materials, and metal
corrosion.
•Lasting low relative humidity can cause washer contraction and
ESD and cause issues including loose mounting screws and circuit
failure.
•High temperature can accelerate the aging of insulation materials
and significantly lower the reliability and lifespan of the switch.
For the temperature and humidity requirements of the switch, see
hardware information and specifications for the switch series
Lightning protection
CAUTION:
Ground the switch correctly and verify the grounding. For more
information, see "Grounding the switch."
•If you ground the switch by using a grounding strip, make sure the
grounding resistance of the grounding strip in the equipment room is
less than 1Ω.
•If you ground the switch by using a grounding conductor buried in
the earth ground, make sure the grounding resistance of the
grounding conductor in the ground is less than 10Ω.
•Route the signal cables along indoor walls, bury the cables in the
earth ground, or thread the cables through steel tubes. Install a
signal lightning arrester with a nominal discharge current for a
corresponding network interface.
•Keep the signal cables far from power cords and lightning rod down
conductors.
•As a best practice, route power cords indoors. If anAC power cord
is routed from outdoors, connect the AC power cord first to a power
lightning arrester before leading it to theAC power port on the
switch. Make sure the power lightning arrester has a nominal
discharge current and the total length of the power cord from the
power lighting arrester to the power port on the switch is less than 5
m (16.40 ft).
•Ground the switch, rack, independent power supplies, and lightning
arresters separately.
•You must ground optical fibers with reinforcing metal stiffener from

6
Item Requirements
outdoors on an optical distribution frame (ODF) or fiber splice
enclosure.
Cable routing
CAUTION:
Do not run an Ethernet cable and power cord in parallel.
•Route different types of cables separately.
•Keep power cords a minimum of 5 cm (1.97 in) away from other
cables.
ESD prevention
•Ground the switch correctly.
•To avoid ESD damage tothe device or components, always wear an
ESD wrist strap when you install or remove the device or
components.
•Make sure the wrist strap has good skin contact and is reliably
grounded.
Cleanliness •For more information, see "Cleanliness."
Corrosive gas prevention The installation site must be free from corrosive gases such as acid
gases and alkaline gases. For more information, see "Corrosive gas
limit."
EMI
•If AC power is used, use a single-phase three-wire power receptacle
with protection earth (PE) to filter interference from the power grid.
•Keep the device far away from radio transmitting stations, radar
stations, and high-frequency devices.
•Use electromagnetic shielding, for example, shielded interface
cables, when necessary.
Cleanliness
Dust buildup on the chassis might cause electrostatic adsorption and dust corrosion, resulting in
poor contact of metal connectors and contact points. This might shorten the device's lifetime and
even cause device failure in the worst case. Table 3 describes the switch requirement for
cleanliness.
Table 3 Switch requirement for cleanliness
Substance Particle diameter Concentration limit
Dust particles ≥ 0.5 µm ≤ 1.8 × 107particles/m3
To maintain cleanliness in the equipment room, follow these guidelines:
•
Keep the equipment room away from pollution sources. Do not smoke, eat, or drink in the
equipment room.
•
Use double-layer glass in windows and seal doors and windows with dust-proof rubber strips.
Use screen doors and window screens for doors and windows open to the outside and make
sure the external windows are air tight.
•
Use dustproof materials for floors, walls, and ceilings and use wallpaper or matt paint that does
not produce powders.
•
Clean the equipment room regularly and clean the air filters of the rack each month.
•
Wear ESD clothing and shoe covers before entering the equipment room, keep the ESD
clothing and shoe covers clean, and change them frequently.

7
Corrosive gas limit
Corrosive gases can accelerate corrosion and aging of metal components. Make sure the corrosive
gases do not exceed the concentration limits as shown inTable 4.
Table 4 Corrosive gas concentration limits
Gas Average concentration (mg/m3) Maximum concentration (mg/m3)
SO20.3 1.0
H2S 0.1 0.5
Cl20.1 0.3
HCI 0.1 0.5
HF 0.01 0.03
NH31.0 3.0
O30.05 0.1
NOX0.5 1.0
CAUTION:
As a best practice, control the
corrosive gas concentrations in the equipment room at their
average
values
. Make sure the corrosive gas concentrations do not exceed 30 minutes per day at their
maximum values.
To control corrosive gases, use the following guidelines:
•
As a best practice, do not build the equipment room in a place with a high concentration of
corrosive gases.
•
Make sure the equipment room is not connected to sewer, vertical shaft, or septic tank pipelines
and keep it far away from these pipelines. The air inlet of the equipment room must be away
from such pollution sources.
•
Use environmentally friendly materials to decorate the equipment room. Avoid using organic
materials that contains harmful gases, such as sulfur or chlorine-containing insulation cottons,
rubber mats, sound-proof cottons, and avoid using plasterboards with high sulfur concentration.
•
Place fuel (diesel or gasoline) engines separately. Do not place them in the same equipment
room with the device. Make sure the exhausted air of the engines will not flow into the
equipment room or towards the air inlet of the air conditioners.
•
Place batteries separately. Do not place them in the same room with the device.
•
Employ a professional company to monitor and control corrosive gases in the equipment room
regularly.
Examining the installation site
Before you install the switch, verify that the installation site meets the installation requirements. The
switch can operate correctly in an A1 or A2 installation site. Availability issues might occur if you
install the switch in an A3, B1, B2, or C installation site.
Table 5 Installation sites
Category Definition Example
A1: indoor controlled •Indoor environments where
temperature and humidity are
Central equipment rooms, IDC
equipment rooms, mobile cabins

8
Category Definition Example
environment
controlled.
•Completely enclosed or shielded
indoor environments.
with air conditioners, outdoor air
conditioner cabinets, and heat
exchanger cabinets.
A2: indoor partially
controlled
environment
•Indoor environments where
temperature and humidity are partially
controlled.
•Incompletely enclosed or shielded
places.
•Places far from pollution sources.
Simple equipment rooms, ordinary
houses, garages, corridors, and
direct ventilation cabinets far from
pollution sources, houses without
direct exposure to sunlight or rain,
railway station platforms, and
stadiums.
A3: indoor
uncontrolled
environment
•Indoor environments where
temperature and humidity are
uncontrolled.
•Incompletely enclosed or shielded
places.
•Places near pollution sources.
Simple equipment rooms, ordinary
houses, garages, corridors, and
direct ventilation cabinets near
pollution sources, houses without
direct exposure to sunlight or rain,
railway station platforms, stadiums,
uncleaned rooms after decoration,
and rooms under decoration.
B1: outdoor general
environment
•Unshielded places where the
temperature and humidity are not
controlled.
•Places far from pollution sources.
Completely exposed outdoor places
far from pollution sources.
B2: harsh
environment
•Unshielded places where the
temperature and humidity are not
controlled.
•Sea environments or outdoor land
environments near pollution sources.
Islands, ships, and completely
exposed outdoor places near
pollution sources.
C: special
environments Special application environments Buried, underwater, or undersea
environments and manholes.
Table 6 Pollution sources
Category Radius range
Saline water areas such as oceans and saline lakes ≤3.7 km (2.30 miles)
Serious pollution sources such as metallurgic plants, coal mines, and
heat and power plants ≤3 km (1.86 miles)
Medium pollution sources such as chemical factories, rubber plants,
and electroplating factories ≤2 km (1.24 miles)
Light pollution sources, such as food factories, tanneries, and
heating boilers ≤1 km (0.62 miles)
Checking power distribution or power supply
environment
Table 7 Requirements for power distribution or power supply environment
Item Requirements
Preparation The power supply must be available before you install the switch.
Voltage
The voltage provided to the switch must be within the operating voltage range.

9
Item Requirements
For the operating voltage range, see S5130S-EI Switch Series Hardware
Information and Specifications.
Power receptacle and
cables
•If the external power supply system provides an AC power outlet, use a
country-specificAC power cord. Make sure the PE wire of theAC power
supply is grounded reliably.
•
If the external power supply system provides a DC distribution box, prepare
DC power cords yourself.
•Do not use the power cord provided with the switch on other devices.
Laser safety
WARNING!
Disconnected optical fibers or
transceiver modules might emit invisible laser light. Do not stare into
beams or view directly with optical instruments when the switch is operating.
The switch is Class 1 laser device.
Installation tools
No installation tools are provided with the switch. Prepare them yourself as required.
•
Flat-blade screwdriver
•
Phillips screwdriver
•
ESD wrist strap
•
Needle-nose pliers
•
Diagonal pliers
•
Crimping pliers
•
Marker

10
Installing the switch
CAUTION:
Keep the tamper
-
proof seal on a mounting screw on the chassis cover intact, and if you want to open
the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence.
Figure 1 Hardware installation flow
Start
Install the switch
Ground the switch
Connect the power cords
Verify the installation
Turn on the circuit
breakers
Operating correctly? Turn off the circuit
breakers
Troubleshoot the
switch
No
Has power supply slots?
Yes
Select and install power
supplies
Yes
No
End
Connect interface cables

11
Installing the switch in a 19-inch rack
Mounting brackets
Table 8 describes the mounting brackets applicable to the switch.
Table 8 Mounting brackets applicable to the switch
Switch model Applicable mounting
brackets Views
S5560S-28P-SI
S5560S-52P-SI
S5560S-28S-SI
S5560S-52S-SI
S5130S-28S-SI
S5130S-28S-SI-MM
S5130S-28S-SI-SM
S5130S-52S-SI
S5130S-28S-LI
S5130S-28S-LI-MM
S5130S-28S-LI-SM
S5130S-52S-LI
S5130S-28S-PWR-LI
S5130S-28S-HPWR-LI
S5130S-52S-PWR-LI
S5120V2-28P-SI
S5120V2-52P-SI
S5120V2-28P-LI
S5120V2-52P-LI
S5120V2-28P-PWR-LI
S5120V2-28P-HPWR-LI
S5120V2-52P-PWR-LI
S5110V2-28P-SI
S5110V2-52P-SI
S5024PV3-EI
S5048PV3-EI
S5024PV3-EI-PWR
S5024PV3-EI-HPWR
S5048PV3-EI-PWR
S5024PV5-EI
S5048PV5-EI
S5024PV5-EI-PWR
S5024PV5-EI-HPWR
S5048PV5-EI-PWR
S5024FV3-EI
S5500V3-24P-SI
S5500V3-48P-SI
Mounting brackets A (provided) See A in Figure 2.

12
Switch model Applicable mounting
brackets Views
S3100V3-28TP-SI
S3100V3-52TP-SI
S3100V3-28TP-PWR-SI
S5560S-28F-SI
S5560S-28DP-SI
S5500V3-28S-SI
S5500V3-28PS-SI
S5500V3-54S-SI
S5500V3-54PS-SI
S5500V3-36F-SI
S5500V3-28S-DP-SI
S5500V3-54S-DP-SI
S5500V3-36F-DP-SI
S5500V3-54F-DP-SI
S5130S-28F-SI
Mounting brackets B (provided) See B in Figure 2.
S5120V2-20P-LI
S5120V2-10P-PWR-LI
S5120V2-12TP-HPWR-LI
S5008PV5-EI-HPWR
S5008PV5-EI-HPWR-S
S5016PV3-EI
S5016PV5-EI
S5016PV5-EI-S
S3100V3-10TP-PWR-SI
S3100V3-20TP-PWR-SI
S5024PV5-EI-S
S5024PV5-EI-PWR-S
S5016PV5-EI-PWR-S
Mounting brackets C with
product code
SOHO-SWITCH-FL-02
(optional)
See C in Figure 2.
S5008PV5-EI
S5008PV5-EI-S
S5120V2-10P-SI
S5120V2-10P-LI
S3100V3-10TP-SI
S3100V3-18TP-SI
Mounting brackets D with
product code
SOHO-SWITCH-FL-01
(optional)
See D in Figure 2.

13
Figure 2 Mounting brackets
(1) Screw hole for attaching the bracket to the switch
(2 ) Screw hole for attaching the bracket to the rack post
Attaching the mounting brackets to the switch
1. Determine the installation position for the mounting brackets.
The S5560S-28F-SI, S5560S-28DP-SI, S5500V3-28S-DP-SI, S5500V3-54S-DP-SI,
S5500V3-36F-DP-SI, S5500V3-54F-DP-SI, and S5130S-28F-SI switches each provide two
mounting positions on the two sides for mounting brackets: one front mounting position
(near the network ports) and one rear mounting position (near the power supplies).
The other switch models provide only one mounting position (near the network ports) for the
mounting brackets.
2. Align one mounting bracket with the screw holes at the mounting position. Use M4 screws to
attach the mounting bracket to the chassis. See Figure 3 for installing mounting bracket A,
Figure 4 and Figure 5 for installing mounting bracket B, Figure 6 for installing mounting bracket
C, and Figure 7 for installing mounting bracket D.
M4 screws are provided only for switches shipped with mounting brackets.
An optional mounting bracket kit contains M4 screws.
3. Repeat step 2to attach the other mounting bracket to the chassis.
1
2
1
2
1
2
1
2
(A) (B)
(C) (D)

14
Figure 3 Attaching mounting bracket A (S5120V2-28P-HPWR-LI switch)
Figure 4 Attaching mounting bracket B (mounting position near the port side, S5560S-28F-SI
switch)
Figure 5 Attaching mounting bracket B (mounting position near the power supply side,
S5560S-28F-SI switch)

15
Figure 6 Attaching mounting bracket C (S5120V2-20P-LI switch)
Figure 7 Attaching mounting bracket D (S5120V2-10P-LI switch)
Rack-mounting the switch
This task requires two people. To mount the switch in the rack:
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
2. Verify that the mounting brackets have been securely attached to the switch chassis.
3. Install cage nuts in the mounting holes in the rack posts.
No cage nuts are provided with the switch. Prepare them yourself.
4. One person holds the switch chassis and aligns the mounting brackets with the mounting holes
in the rack posts, and the other person attaches the mounting brackets to the rack with M6
screws.
If the switch is not shipped with M6 screws, prepare them yourself.
5. Verify that the switch chassis is horizontal and secure.

16
Figure 8 Mounting the switch in a rack (S5120V2-28P-HPWR-LI switch)
Figure 9 Mounting the switch in a rack (mounting brackets installed near the port side,
S5560S-28F-SI switch)
Figure 10 Mounting the switch in a rack (mounting brackets installed near the power supply
side, S5560S-28F-SI switch)

17
Figure 11 Mounting the switch in a rack (S5120V2-10P-PWR-LI switch)
Figure 12 Mounting the switch in a rack (S5120V2-10P-LI)
Mounting the switch on a workbench
IMPORTANT:
•
Ensure 10 cm (3.9 in) of clearance around the chassis for heat dissipation.
•Do not place heavy objects on the switch.
If a standard 19-inch rack is not available, you can place your switch on a workbench.
To mount the switch on a workbench:
1. Verify that the workbench is sturdy and reliably grounded.
2. Place the switch with bottom up, and clean the round holes in the chassis bottom with dry cloth.
3. Attach the rubber feet to the four round holes in the chassis bottom.
4. Place the switch with upside up on the workbench.

18
Mounting the switch on a wall
CAUTION:
•
Before drilling holes in a wall, make sure no electrical lines exist in the wall.
•Leave a minimum clearance of 10 mm (0.39 in) around the chassis for heat dissipation.
The S5120V2-SI, S5120V2-LI, S5000V3-EI, S5000V5-EI, and S3100V3-SI switch series support
wall mounting. These switches are provided with screw anchors and screws as shown in Figure 13
for wall-mounting.
Figure 13 Screw anchor and screw
Table 9 describes the switch models that support wall mounting and installation holes distances
required for wall-mounting the switch.
Table 9 Installation hole distances for switch models that support wall mounting
Switch model Hole distance
S5120V2-10P-SI
S5120V2-10P-LI
S3100V3-10TP-SI
S5024PV5-EI-S
S5008PV5-EI with product code
LS-5008PV5-EI-H1
S5008PV5-EI-S
S5008PV5-EI-HPWR-S
170 mm (6.69 in)
S3100V3-18TP-SI 172 mm (6.77 in)
S5120V2-20P-LI
S5016PV3-EI
S5016PV5-EI
S5016PV5-EI-S
176 mm (6.93 in)
S5120V2-10P-PWR-LI
S5120V2-12TP-HPWR-LI
S3100V3-10TP-PWR-SI
S5008PV5-EI-HPWR with product code
LS-5008PV5-EI-HPWR-H1
102 mm (4.02 in)
S3100V3-20TP-PWR-SI
S5016PV5-EI-PWR-S
S5024PV5-EI-PWR-S 116 mm (4.57 in)
To mount the switch on a wall:
1. Mark two installation holes on the wall. Make sure the two holes are on the same horizontal line.
See Table 9 for the distance requirement between the two holes.