Habitat Extendable Austin Radiator Cover 951/9901 User manual

Extendable
Austin
Radiator
Cover
1
Spare Parts
www.argos-support.co.uk
[e-mail]
0370 112 1928
Customer Support
0345 640 2020
Issue 1 - 01/06/2021

22
Safety and Care Advice
Care and maintenance
Additional Guidance
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• This product has been
constructed to be used in the
domestic environment only and
not for commercial purposes.
• We do not
recommend the
use of power drill/
drivers for inserting
screws as this could
damage the unit.
Only use hand screwdrivers.
• Parts of the assembly will be
easier with 2 people.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent. Do not use
abrasive cleaners.
• From time to time check that
there are no loose screws, nuts
or bolts. If there are please re-
tighten.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully
tighten the bolts.
•Regularly check and ensure that all bolts and fittings are tightened properly.
•The assembled product must be fixed/secured to a wall which is in good condition using the screws and
wall plugs provided.
WARNING
In order to help prevent overturning
PLEASE FOLLOW THESE INSTRUCTIONS-
To help prevent product toppling over please follow these steps-
Do not allow children to climb or hang on the furniture
Do not open more than one drawer at a time
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless furniture has
been designed for this purpose
You will need to provide wall plugs and screws applicable for your wall
type
Product Details
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
WHITE 951/9901
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or
your floor.
•The surface should be
protected from liquids, heat or
cold by using a coaster or mat.
The surface is not water resistant
and may be damaged or
discoloured if not protected.

3
Phillips screwdriver
Flathead screwdriver
Bag 1
Fittings(Shown to scale)
Tools required
6 x 35 mm
locking screw x 18
15 x 9.5 mm
locking connector x 18 dowel x 4 screw x 12
φ6 x 18mm
φ6 x 30mm
φ6 x 10mm
screw x 8
φ3 x 14mm
small screw x 14 50 x 40 x 15mm panel x 2 160 x 127 x 18mm nut x 2
wall plug x 4
E

4
Panels
1
Centre x 1
80 x 22.2 x 30 cm
1
2
Top panel - Left x 1
67.6 x 21 x 1.5 cm
2
3
Top panel - Right x 1
67.6 x 21 x 1.5 cm
3
Support bar 1 x 1
54.1 x 10.6 x 1.5 cm
4Support bar 2 x 1
54.1 x 10.6 x 1.5 cm
5Support bar 3 x 1
54.1 x 10.6 x 1.5 cm
6
55
Support bar 4 x 1
54.1 x 10.6 x 1.5 cm
7Left side panel x 1
91 x 18.3 x 1.5 cm
8Right side panel x 1
91 x 18.3 x 1.5 cm
9
Left decoration panel x 1
91 x 11 x 1.5 cm
10 Right decoration panel x 1
91 x 11 x 1.5 cm
8
10
11

Panels
5
13
Decoration panel 1 x 2
60 x 53 x 0.5 cm
12
12
12
Decoration panel 2 x 1
80 x 78.4 x 1.2 cm
13
7
6
5
2
3
1
10
11
12
12
13

6
2
3
10
10
11
11
1
2
6 x 35 mm
locking screw x 18
15 x 9.5 mm
locking connector x 6

7
7
6
2
3
1
3
5
13
screw x 12
φ6 x 18mm
To change the width of
the cover -
Screw D through panels 2
and 3 into panel 1 and
through panels 4 - 7 into
13 to give the desired
width. The inner most
holes giving the smallest
width and the outermost
holes the widest setting.
Ensure the holes used in
panel 1 match panel 11.

7
6
5
4
5
12
12
11
10
8
15 x 9.5 mm
locking connector x 8 dowel x 4
φ6 x 30mm
φ3 x 14mm
small screw x 14

2
3
6
7
9
15 x 9.5 mm
locking connector x 4
160 x 127 x 18mm
nut x 2
φ6 x 10mm
screw x 8
E

8
wall
9
wall plug x 4
10
50 x 40 x 15mm
panel x 2 G!WARNIN