Habitat RADI-BD-SS18-A User manual

Width - 150cm
Depth- 221cm
Height - 84cm
Assembly Instructions - Please keep for future reference
Tools required
Dimensions
Important – Please read these instructions before assembly
If you need help or have damaged or missing parts, email:
[e-mail] or call: 0344 499 4686
Radius Beds - 90cm, 135cm and 150cm
RADI-BD-SS18-A
Width - 135cm
Depth- 211cm
Height - 84cm
Dimensions
1 2 1
1
Dimensions
Width - 90cm
Depth- 211cm
Height - 84cm

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
If for any reason you should have
problems with your Habitat product,
please contact the store from which
you purchased it.
Please retain your receipt as proof of
purchase.
If you have any comments or
suggestions regarding this product,
assembly instructions or service
received, please contact the store or
Habitat Head Office via its website:
www.habitat.co.uk
or write directly to: Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW
General information
Check you have all the
components and tools listed on the
front cover and pages 2 - 3.
Remove all fi
ttings from the plastic
bags and separate them into their
groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough space
to layout the parts before starting.
Do not stand or put weight on the
product, this could cause damage.
Assemble the item as close to its
final position (in the same room) as
possible.
Do not place furniture directly in
front of radiators, fi
res or any other
source of heat.
Parts of the assembly
will be easier with 2
will be easier with 2
people.
Assemble on a soft level surface
to avoid damaging the unit or your
floor.
We do not
recommend the
use of power drill/
drivers for inserting
screws, as this c ould
damage the unit. Only use hand
screwdrivers.
Dispose of all packaging carefully
and responsibly.
Take care to prevent sharp objects
e.g. toys, buckles and heels from
coming into contact with your
furniture, and avoid contact with
chemicals e.g. cosmetics or hair
products which may permanently
mark the surface.
General care and maintenance
Dust regularly with a clean dry cloth.
Wipe up any spills immediately with a damp cloth and then dry
the surface with a clean dry duster.
Repeat this procedure for periodic cleaning.
Remove stubborn stains with a weak washing up liquid solution
and a damp cloth and dry after with a clean cloth.
The use of furniture polish or spray is not necessary or recommended.
Never use abrasive or corrosive cleaning agents.
Cleaning and care of lacquered surfaces
1 2
Maximum weight limit
2
300kg
MAX
Bed -90cm
Bed -135,150cm
150kg
MAX
Take care when moving furniture -
dragging it across the oor will loosen
and damage the joints.
Always lift and move.
From time to time check that there are
no loose ttings. Tighten as necessary.
Avoid exposing your furniture to direct
and prolonged periods of sunlight and
heat sources as fading and
cracking may occur.

BC Note: There are ‘Batch Code’ lables where shown on the indicated items, these should be retained.
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, email:
customerservic [email protected] o.uk or call: 0344 499 4686
3
Please check you have all the panels listed below
1/2
1
2
5
5
5
3
4
2/2

Please check you have all the fixings listed below
Note: The quantities below are the correct amount to complete the assembly. In some
cases mor e fittings may be supplied than are required.
Components - Fittings
A
Ruler - To help correctly identify thefixings
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120
105
If you need help or have damaged or missing parts, email:
customerservic [email protected] o.uk or call: 0344 499 4686
4
B
x 6 screw 24
C
metric screw xx 6
DE
metal support
F
G
x 8
H
x 4
metric hex nut felt pad
metric nut x 6 threaded bolt x 8 moon washer x 8
Fittings pack contained in pack 1/2

5
Assembly Instructions
Step 1
Step 2
1
x 6A
3
4
x 24
B
2
1
x 2H
x 4
E

6
Assembly Instructions
Step 3
Step 4
1
1
x 2H
x 4
E
1
2
3
4
1 2 3
4
1 2 1
1
x 8
F
x 8
G

7
Assembly Instructions
Step 5
1 2 1
1
1
2
3
4
5
5
5
5
3
4
x 6D
x 6C
Please Note
The DUO slat kit for your bed is supplied in a separate pack.