Habitat JENSON 935/7709 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
Issue 1 - 15/09/20
JENSON
Gloss
935/7709 914/8664

Safety
Important - Please read these instructions fully before starting assembly
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 31
for wall fixing information.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
• Warning: This unit weighs
approximately 40 kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.

Cabinet Panels DO NOT REMOVE any protective film until after assembly
56.2 x 35.4 cm
DF-00022147
1177.8 x 36.9 cm 2
3
6
7
10
911
8
4
5
177.8 x 36.9 cm
DF-00022142
DF-00022153
59.6 x 39 cm
DF-00022144
56.2 x 35.4 cm
DF-00022154
40.8 x 35.3 cm
DF-00022146
x3
x2
x4
56.2 x 6 cm
DF-00022150
56.2 x 35.4 cm
DF-00022145
42.1 x 29.2 cm
DF-00023214
42 x 42 cm
DF-00022148
57.2 x 47.8 cm
DF-00022149

DO NOT REMOVE any protective film until after assembly
Drawer Panels Note: the internal drawer panels are grey
12 13 14
16
15
58.8 x 18.9 cm
DF-00022152
35 x 14 cm
52.95 x 14 cm
54.5 x 34.7 cm
35 x 14 cm
WRP-00000491
WRP-00000493
DF-00023215
WRP-00000492
x2
x2
x2
x2 x2

Fittings Use these drawings to
correctly identify the fittings
Tools
Only used for
drilling walls
F171GY
Bag 1
Bag 2
Kx 4 Mx 8
A
F901
F22
Ax 30 Cx 36
L
F607 F74
x 4
J
F646
x 4
A
F901
Ax 4
x 4
F137
I
F73
x 8
H
Dx 6
F639
x 8
F639
x12
Bx 30
F900
GH
F277
x 16
F276
x 6
F65
E
F

Fittings
F474
Nx 2
F450
Ox 4
Tools
Only used for
drilling walls

1
Ex 8
Ox 4
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Bag 1
A
F901
F22
Ax 30 Cx 36
J
F646
x 4
x 4
F137
I
F73
x 8
Dx 6
F639
x12
Bx 30
F900
GH
F277
x 16
F276
x 6
F65
E
F
1
2
A B
2nd hole
Finished
front edges

2
Cx 4
1
2
1
2
Ax 20
3
Bx 4

4
Bx 6 Cx 12
Finished
front edge
4
6
x 3
5
Ax 2 Bx 4 Cx 4 Finished
front edge
6
Dx 2
6
4
Finished
front edge
Finished
front edge

7
6
Finished
front edge
4
8
Finished
front edge
Finished
front edge
Finished
front edge
4

10
Finished
front edge
4
7
Finished
front edge
Finished
front edge
Dx 2
9
Ax 2 Bx 4 Cx 4
7

11
12
Finished
front edge
4
Bx 4 Cx 4
Finished
front edge
8
7
4
x 2

13
Finished
front edge
4
8
Dx 2
Finished
front edge
Finished
front edge
Finished
front edge
14
15
Finished
front edge
1
x 6

Bx 8 Cx 8
16 x4
17
5
5
5
5
5
18 x 4

19
20
2
Finished
front edge
x 10

2
21
22
‘Tap’
Jx 4
A = B Make sure measurement A and B
are the same before fixing the
Back panel in the next step
B
B
A
A

23
24
10
IMPORTANT:
Back panel 9 must be
flush with the Back Rail
9
11
11
IMPORTANT:
You will need to keep 6
nails for the next step
x 10
G
IMPORTANT:
Back panel 9 must be
flush with the Back Rail

25
26
Gx 6
Fx 6
Ax 6
3
Finished
front edge

27
28
3Finished
front edge
IMPORTANT:
The back panel must slot
into the groove in the top
panel
x 6

29
30
Carefully turn the unit around
and move it into its final
position up against the wall.
Hx 12