hager 4600 Series User manual

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Rev 2, Rev Date: 02/06/2020 Page 1 of 8
DEVICES COVERED IN THIS DOCUMENT:
• 4600 SERIES RIM PANIC NARROW STILE EXIT DEVICE
• 4600 SERIES RIM FIRE NARROW STILE EXIT DEVICE
OVERVIEW
APPLICATIONS
4950 BLADE STOP STRIKE SINGLE DOOR 4920 STANDARD STRIKE SINGLE DOOR
4920 STANDARD STRIKE AND MULLION
4920 Strike Applicaon
Single Door Panic-Rated Exit Hardware
(4920F Strike Standard for Fire-Rated Devices)
4920 Strike Applicaon
Double Door Panic-Rated Exit Hardware
(4912 Strike Available for Fire-Rated Mullion
Applicaons)
4950 Blade Stop Strike Applicaon
Single Door Panic-Rated Exit Hardware

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Page 2 of 8 Rev 2, Rev Date: 02/06/2020
4952 SEMI-FLUSH STRIKE AND MULLION 4950 BLADE STOP STRIKE AND MULLION
4952 Semi-Flush Strike Applicaon
Single or Double Door Panic-Rated Exit Hardware
4950 Blade Stop Strike Applicaon
Single or Double Door Panic-Rated Exit Hardware
SUPPLIED PARTS
Tools Required
Chassis
Flush End Cap
Bracket
Dogging Device
(Only on Panic Hardware)
Flush End Cap
Device Body
Head Cover
4965R
Dogging Hex Key
(Supplied with Panic Hardware only)
Panic Exit Device Shown
(Fire Rated Device Available)
4950 Panic Blade Stop Strike
(Provided with Panic Device)
4920 Panic Strike for Standard Frame
(Purchased Separately)
4920F Fire-Rated Strike for Standard Frame
(Provided with Fire-Rated Device)
4952 Panic Semi-Flush Strike
(Purchased Separately)

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Rev 2, Rev Date: 02/06/2020 Page 3 of 8
1. MARK DOOR
A. Measure and draw center line on door and frame, typically 40” from
nished oor.
B. Fold and apply templates to door and frame.
C. Refer to website for templates.
2. DRILL MOUNTING HOLES
A. Mark, drill and tap holes as shown on door and frame templates. Do not drill center hole on strike u nl aer strike has been
mounted and adjusted at the end of the installaon.

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Page 4 of 8 Rev 2, Rev Date: 02/06/2020
3. INSTALL STRIKE
A. Install strike using the two outer mounng holes.

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Rev 2, Rev Date: 02/06/2020 Page 5 of 8
3. INSTALL STRIKE (CONTINUED)
4. INSTALL 4950 WEAR STRIP (SKIP IF USING A DIFFERENT STRIKE)
A. Place wear strip on frame and center on strike.
B. Hold in place and mark all 4 hole locaons.
C. Drill 1/8” diameter holes in 4 places and install wear strip with
Flat head drive rivets (provided).

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Page 6 of 8 Rev 2, Rev Date: 02/06/2020
5. CUT EXIT DEVICE TO LENGTH
A. Remove head cover from exit device chassis.
B. Align device with mounng holes and measure to determine length to cut device. The clearance between the frame
stop and end of exit device (with end cap removed) is 1-5/8” (See Figure 5-1).
C. Cut device square with hack saw or metal cung saw blade and deburr edges. Make sure cut is straight or the end cap won’t
sit ush. Be sure to save the spring clip on the dogging plate cover for use on the device. (See Figure 5-2).
6. INSTALL DEVICE
A. Mount exit device using the provided screws. If using trim be sure to line up trim actuang sha (tailpiece) with cam located
on back of exit device chassis.
The clearance is measured from the
frame stop to end the of the device
(without end cap).
Figure 5-1
Figure 5-2

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Rev 2, Rev Date: 02/06/2020 Page 7 of 8
7. INSTALL FLUSH END CAP
A. Remove the ush end cap from the ush end cap bracket.
B. Mark hole locaons by holding ush end cap bracket up against door and device. Be sure exit device is level before inserng
the ush end cap bracket into the device.
C. Mark and drill/tap holes.
D. Install ush end cap bracket and ush end cap using supplied screws (See Figure 7-1). If the ush end cap is not ush with the
exit device, remove ush end cap and adjust the mounng screws and the ush end cap bracket as needed (See Figure 7-2)..
8. TEST AND ADJUST
A. Check engagement between exit device and strike.
Shim strike as needed for a 9/32” clearance between
strike and chassis.
B. Check opening and closing door. Repeat this with head
cover to make sure head cover does not hit the strike.
C. If device operates properly, drill/tap and install center
screw in strike (if applicable).
Figure 7-1
Figure 7-2

4600 SERIES RIM NARROW STILE EXIT DEVICE
INSTALLATION INSTRUCTION
I-ED01162
Hager Companies 139 Victor Street, St. Louis, MO 63104 [phone] www.hagerco.com
Page 8 of 8 Rev 2, Rev Date: 02/06/2020
9. INSTALL HEAD COVER
A. Install head cover on chassis using provided screws.
10. DOGGING DEVICE
A. For increased life of the device, dog the push bar down during high trac periods of the day.
B. Hex Wrench Dogging:
To dog the device, press the push bar, insert the hex dogging wrench and turn clockwise 35 degrees. The push bar will remain
depressed and the latch will stay in the Door Open Posion. (See Figure 10-1) To release the dogging, hold the push bar
down, insert the hex dogging wrench and turn counter-clockwise 35 degrees. The push bar will return to the up posion and
the latch will actuate to lock the door.
C. Cylinder Dogging:
Required hardware for cylinder dogging includes one (1)
morse cylinder, lengths 1-1/8”, 1-1/4” or 1-3/8”with a
standard cam (0.723” [18mm] screw center to p of cam):
and one (1) Hager Cylinder Dogging kit (4925R) which
includes one (1) 11/32” [8.7mm] solid cylinder collar and
cashbox nut. (See Figure 10-2) Remove and discard the
hex wrench extension. (See Figure 10-3) The cylinder
should be oriented so the cam is poinng away from the
exit device push bar. (See Figure 10-4) Install the dogging
cover plate with the cylinder and test the dogging.
(See Figure 10-5) Depress the push bar, insert the key and
turn the key clockwise to dog the device. Turn the key
counter-clockwise to release the dogging.
Figure 10-1
Figure 10-2
Figure 10-5
Figure 10-4
Figure 10-3