hager 5300 Series User manual

END CAP
SLIDE INSERT
HOLD OPEN STOP
MOUNTING
SCREW
Hold Open Stop
Stop Only
Slide Insert
5 3/16"
131.8
19 7/8"
504.8
4 13/32"
112
9 1/16"
230
3/4"
19
1"
25.1
1"
25.8
SLIDE TRACK
SLIDE ARM
SLIDE ARM INSERT
SCREW
END CAP
PARTS
INSTALL TRACK ARM - PULL SIDE APPLICATION (RIGHT HAND SHOWN) 120
TEMPLATE
WITH SLIDE ARM WITHOUT SLIDE ARM
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
Installation Sequence:
Use template to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws. 1.
Determine door width, adjust spring power of closer by referencing closer installation instructions. 2.
Fasten closer body to door with power adjustment nut away from hinge. 3.
Fasten slide track to frame face with open side facing down and with hold open stop end toward 4.
hinge edge of door.
Place slide arm on pinion shaft of closer at preload of 45 degree angle out from door face. 5.
Secure arm with arm washer and arm screw. 6.
Secure other end of slide arm to track by screwing it to the slide insert. Open door to required 7.
opening angle. Then slide stop only/hold open stop up against slider insert and tighten down the
stop only/hold open stop via set screw.
CENTERLINE
OF HINGE
5300 Series Track Arm
Installation Instructions
I-CL00579
REV: 1 REV DATE: 1/11/2014
Page 1 of 3

3 1/8"
79.4
4 9/32"
108.8
9 1/16"
230
1 1/2"
38.1
3/4"
19
3/8"
9.6
19 7/8"
504.8
CENTERLINE
OF HINGE
NOTE
: AN OPTIONAL
MOUNTING PLATE
(5917) IS REQUIRED
WHERE THE HEAD
FRAME FACE IS
LESS THAN 3-1/2"
23 1/4"
590.6
5 3/4"
146.1
8 3/8"
212.7
5 3/4"
146.1
11 5/8"
295.2
9 1/16"
230
3/4"
19
2 1/2"
63.1
Center Track On
Frame Soffit
Installation Sequence:
Use template to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws. 1.
Determine door width, adjust spring power of closer by referencing closer installation instructions. 2.
Fasten closer body to frame with power adjustment nut away from hinge. 3.
Fasten slide track to door face with open side facing up and with hold open stop end toward 4.
hinge edge of door.
Place slide arm on pinion shaft of closer at preload of 45 degree angle out from door face. 5.
Secure arm with arm washer and arm screw. 6.
Secure other end of slide arm to track by screwing it to the slide insert. Open door to required 7.
opening angle. Then slide stop only/hold open stop up against slider insert and tighten down the
stop only/hold open stop via set screw.
INSTALL TRACK ARM - TOP JAMB (PULL SIDE) MOUNTING APPLICATION (RIGHT HAND SHOWN) 180 TEMPLATE
Installation Sequence:
Use template to locate holes on door and frame. Drill 1/8" pilot holes for the self tapping screws. 1.
Determine door width, adjust spring power of closer by referencing closer installation instructions. 2.
Fasten closer body to door with power adjustment nut away from hinge. 3.
Fasten slide track to frame face with open side facing down and with hold open stop end toward 4.
hinge edge of door.
Place slide arm on pinion shaft of closer at preload of 45 degree angle out from door face. 5.
Secure arm with arm washer and arm screw. 6.
Secure other end of slide arm to track by screwing it to the slide insert. Open door to required 7.
opening angle. Then slide stop only/hold open stop up against slider insert and tighten down the
stop only/hold open stop via set screw.
INSTALL TRACK ARM - PUSH SIDE APPLICATION (RIGHT HAND SHOWN) 120 TEMPLATE
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
NOTE: IF USER
WISHES
TO HAVE A
LESSER
SWING ANGLE,
SIMPLY
MOVE HOLD
OPEN STOP
OR STOP ONLY
AWAY FROM
THE PIVOT
HINGE IN
INCREMENTS
OF 1/2" UNTIL
DESIRED
ANGLE IS
ACHIEVED.
HINGE CENTERLINE ON
BACKSIDE OF DOOR
Page 2 of 3
REV: 1 REV DATE: 1/11/2014
5300 Series Track Arm
Installation Instructions
I-CL00579

END CAP
SLIDE INSERT
HOLD OPEN STOP
MOUNTING
SCREW
Hold Open Stop
Stop Only
Slide Insert
B
21 5/16"
541.3
Pocket Depth 2-1/2"-5"
Mount track 1-1/16"
above top of door to
center of screw holes on
track
SLIDE TRACK
SLIDE ARM
SLIDE ARM INSERT
SCREW
END CAP
PARTS
WITH SLIDE ARM WITHOUT SLIDE ARM
Installation Sequence:
Use template above to locate mounting holes on pocket wall and mount closer according to pull 1.
side application template. Drill 1/8" pilot holes for the self tapping screws.
Determine door width, adjust spring power of closer by referencing closer installation 2.
instructions.
Fasten closer body to door with power adjustment nut away from hinge. 3.
Fasten slide track to pocket wall face with open side facing down and with hold open stop end 4.
away from hinge edge of door.
Place slide arm on pinion shaft of closer at preload of 45 degrees out from pocket wall. 5.
Secure arm with arm washer and arm screw. 6.
Push arm towards door to pretension closer then secure other end of slide arm to track by 7.
screwing it to the slide insert. Open door to required opening angle. Then slide stop only/hold
open stop up against slider insert and tighten down the stop only/hold open stop via set screw.
Pocket Pivots 6-1/2"
4-1/2" x 4-1/2" Hinges,
Swing Clear Hinges,
or 3/4" Offset Pivots
5"
Dim "B" Pivot/Hinge Type
INSTALL TRACK ARM - POCKET DOOR APPLICATION 90
OPEN DOOR INTO POCKET
5300 Series Track Arm
Installation Instructions
I-CL00579
REV: 1 REV DATE: 1/11/2014
Page 3 of 3