hager 2941 User manual

2941/2942 Magnetic Lock
Installation Instructions
I-EA00053
Rev 5, Rev Date: 11/15/22
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • [phone]
The 2941 & 2942 magnetic locks are mounted to the underside of the header, on the stop side of
the door.
INSTALLATION INSTRUCTIONS
2941/2942 MAGNETIC LOCKS
Electrical Guidelines:
• Use properly fused U. L. Listed Power Supply
• Do not install a diode in parallel with any magnetic lock. A diode will cause a delay when releasing the door and
residual magnetism to occur.
• Any low voltage condition will cause erratic operation of the optional board sensor.
Mechanical Guidelines:
• Handle the equipment with care, damaging the mating surfaces of the magnet or armature plate may reduce locking
efficiency.
• The magnet mounts rigidly to the door frame. The armature plate mounts to the door. The kit provided allows the
armature to pivot about its center to compensate for door wear and misalignment.
• Template use must take place with the door installed in its normally closed position (do not pre-prep door and frame
separately or alignment issues may occur).
• Before installing, add thread-locker to all screws.
Maintenance Guidelines:
• Do not touch the lock face with your hands.
• Clean lock face with scouring pad (do not use sandpaper).
• Apply a thin film of rust inhibitor on lock face.
• Repeat application on armature plate.
Electrical Specifications:
Dual Voltage 12 or 24VDC
Power Consumption 505mA@12VDC
260mA@24VDC
DS Door Position Sensor SPDT, 1A@24VDC
LS Lock Status Sensor SPDT, 1A@24VDC
Supplied Mounting Hardware (2941 & 2942)
2942 only

2941/2942 Magnetic Lock
Installation Instructions
I-EA00053
Rev 5, Rev Date: 11/15/22
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • [phone]
Installation
1. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb
side of the frame.
2. Mark and drill holes as indicated by the template.
3. Mount the armature plate to the door using 1 rubber washer sandwiched between 2 steel washers as shown below.
4. Install mounting plate to header. Loosely fasten screws going through adjustment slot. Assure that the mounting plate
and armature line up properly, then tighten down ALL mounting screws.
5. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping
the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing
CAUTION: The magnetic lock body must be held in place until secured with mounting screws.
6. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock.
REINFORCEMENT
TUBE 1-3/4“ HOLLOW
METAL DOOR
5/8“ DRILL
STEEL WASHER 2X
RUBBER WASHER
ARMATURE 1/2” DRILL
SEXNUT
REINFORCEMENT
TUBE 1-3/4“ HOLLOW
METAL DOOR
5/8“ DRILL
STEEL WASHER 2X
RUBBER WASHER
ARMATURE 1/2” DRILL
SEXNUT
7. Test operation. When all is operating properly. Install anti-tamper plugs over socket head
screws using a soft hammer to avoid damage to the housing.
COM NC
NO
Door Position Sensor (Reed switch)
RED (open with door closed)
GREEN (closed with door closed)
BLACK COM NC
NO
Door Position Sensor (Reed switch)
RED (open with door closed)
GREEN (closed with door closed)
BLACK
Power
Supply
Lock
Status
Switch
Voltage Jumper 12VDC
24VDC 12VDC 24VDC
A RED LED INDICATES ENERGIZED &
UNSECURED (GREEN=ENERGIZED &
SECURE)
LED
2942 2941
Voltage Jumper
Power
Supply
Lock
Status
Switch
LED
Performance Level
Destructive: Level 1 Line Security: Level 1
Endurance: Level 2 Standby Power: Level 1
• Installation & wiring in compliance with ANSI/NFPA70 requirements
• Wiring must be cased to avoid outer cable damage
• Terminal: 12~22AWG