Haier HSU-09H03/R1 User manual

No.
OPERATION MANUAL
SPLIT TYPE ROOM AIR CONDITIONER
Please read this operation manual before using the air conditioner.
HSU-09H03/R2(DB)
HSU-12H03/R2(DB)

Before disposing an old air conditioner that
goes out of use, please make sure it's inop-
erative and safe.Unplug the air conditioner
in order to avoid the risk of child entrapment.
It must be noticed that air conditioner system
contains refrigerants, which require speciali-
zed waste disposal.The valuable materials
contained in an air conditioner can be recycled
.Contact your local waste disposal center for
proper disposal of an old air conditioner and
contact your local authority or your dealer if
you have any question.Please ensure that
the pipework of your air conditioner does not
get damaged prior to being picked up by the
relevant waste disposal center, and contribute
to environmental awareness by insisting on an
appropriate, anti-pollution method of disposal.
Disposal of the old air conditioner
Disposal of the packaging of your
new air conditioner
Before starting the air conditioner, read the
information given in the User's Guide caref-
ully.The User's Guide contains very impor-
tant observations relating to the assembly,
operation and maintenance of the air
conditioner.
The manufacturer does not accept respon-
sibility for any damages that may arise due
to non-observation of the following
instruction.
Damaged air conditioners are not to be
put into operation.In case of doubt, consult
your supplier.
Use of the air conditioner is to be carried
out in strict compliance with the relative
instructions set forth in the User's Guide.
Installation shall be done by professional
people, don't install unit by yourself.
For the purpose of the safety,the air con-
ditioner must be properly grounded in acco-
rdance with specifications.
Always remember to unplug the air
conditioner before openning inlet grill. Never
unplug your air conditioner by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.
All electrical repairs must be carried out
by qualified electricians.Inadequate repairs
may result in a major source of danger for
the user of the air conditioner.
Safety Instructions andWarnings
All the packaging materials employed in the
package of your new air conditioner may be
disposed without any danger to the
environment.
The cardboard box may be broken or cut into
smaller pieces and given to a waste paper
disposal service.The wrapping bag made of
polyethylene and the polyethylene foam pads
All these valuable materials may be taken to
a waste collecting center and used again after
adequate recycling.
Consult your local authorities for the name
and address of the waste materials collecting
centers and waste paper disposal services
nearest to your house.
Do not damage any parts of the air
conditioner that carry refrigerant by piercing
or performating the air conditioner's tubes
with sharp or pointed items, crushing or
twisting any tubes, or scraping the coatings
off the surfaces.If the refrigerant spurts
out and gets into eyes, it may result in
serious eye injuries.
Cautions

2. If the power supply cord is damaged, it
must be replaced by the manufacturer
or its service agent or a similar qualified
person.
3. If the fuse of indoor unit on PC board is
broken,please change it with the type of
T. 3.15A/ 250V.
4.The wiring method should be in line with
the local wiring standard.
5. After installation, the power plug should
be easily reached.
6.The waste battery should be disposed
properly.
7.The appliance is not intended to use
by young children or infirm persons
without supervision.
8.Young children should be supervised
to ensure that they do not play with
the appliance.
9 .The distance between the indoor unit and
the floor should be more than 2m.
Do not obstruct or cover the ventilation
grille of the air conditoner.Do not put fingers
or any other things into the inlet/outlet and
swing louver.
Do not allow children to play with the air
conditioner.In no case should children be
allowed to sit on the outdoor unit.
The refrigerating circuit is leak-proof.
1.Applicable ambient temperature range:
Specifications
The machine is adaptive in following
situation
Cooling Indoor Maximum:D.B/W.B
Maximum:D.B/W.B
Minimum: D.B
Maximum:D.B
Minimum: D.B
Minimum: D.B/W.B
Maximum:D.B/W.B
Minimum: D.B/W.B
Outdoor
Indoor
Outdoor
Heating
32oC/23oC
24oC/18oC
43oC/26oC
18oC
27oC
15oC
18oC/14oC
-15oC
Cautions
11 .The wiring diagram is attached inside
the machine.
10.The appliance must be installed on
strong enough supporter.

Cautions
Safety Instruction
Installation
WARNING
Please read the following Safety Instructions carefully prior to use
The instructions are classified into two levels, WARNING and CAUTION according to
the seriousness of possible risks and damages as follows. Compliance to the
instructions are strictly required for safety use.
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
Installation in a inadequate place may cause accidents.Do not install in the following place.
STRICT
ENFORCEMENT
Connect the earth
cable.
earthing
Do not install in the
place where there is
any possibility of
inflammable gas
leakage around the
unit.
Do not get the unit
exposed to vapor
or oil steam.
Check proper
installation of the
drainage securely
PROHIBITION PROHIBITION
CAUTION

Cautions
WARNING
When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.
OFF
Use an exclusive power source with a
circuit breaker
ENFORCEMENT
Connect power supply cord
to the outlet completely Use the proper voltage
Do not use power supply cord
in a bundle. Take care not to damage
the power supply cord.
Do not use power supply cord
extended or connected in halfway
STRICT
ENFORCEMENT
STRICT
STRICT
ENFORCEMENT PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not start or stop the
operation by disconnecting
the power supply cord and so on.
Do not channel the air flow directly
at people, especially at infants or
the aged.
Do not try to repair or reconstruct
by yourself.
Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.
CAUTION
Take fresh air occasionally especially
when gas appliance is running at the
same time.
PROHIBITION STRICT
ENFORCEMENT
Do not operate the switch with
wet hand.
PROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not install the unit near a fireplace
or other heating apparatus. Check good condition of the
installation stand Do not pour water onto the unit
for cleaning
PROHIBITION
Do not place animals or plants in
the direct path of the air flow Do not place any objects on or
climb on the unit. Do not place flower vase or water
containers on the top of the unit.
Do not insert objects into the air
inlet or outlet.
PROHIBITION
PROHIBITION
PROHIBITION

Parts and Functions
Indoor unit
Air filter
Vertical flap
Use remote controller to
adjust up and down air flow.
(Don't adjust it manually.)
Lights up when unit starts.
Power indicator Lights up when Timer operation
is selected.
Timer mode indicator
Lights up during compressor
Operation mode indicator
running.
Remote signal receiver
A beeping sound is generated when
a signal from remote controller is
received.
Test running switch(manual)
Used only for test running in cooling
when room temp. is below 16oC.
Don't use it in normal operation.
Emergency switch(manual)
Used when remote controller is lost or
defective. Unit will run temporarily.
Outdoor unit
OUTLET
INLET
DRAIN HOSE
CONNECTING PIPING AND ELECTRICAL WIRING
Inlet grille

Buttons and display of the remote controller.
16. FAN button
Used to select fan speed: AUTO, HI,MED,LOW,
17 ON/OFF button
Used for unit start and stop.
18. POWER/SOFT button
19. LOCK
Used to lock buttons and LCD display. If
pressed, the other buttons will be disabled
and the lock condition display appears.
Press it once again, lock will be cancelled
and lock condition display disappears.
20. CODE
Used to select CODE A or B with a press,A or
B will be displayed on LCD.
Please select A without special explanation.
1. SWING button
Used to select up or down air sending direction.
2. HOUR button
Used to set timer setting.
3. MODE button
Used to select operation mode. COOL,DRY,
HEAT.
4.TIMER button
Used to select TIMER ON,
TIMER OFF, TIMER ON-OFF.
5. RESET
When the remote controller appears
abnormal, use a sharp pointed article
to press this button to reset the
remote controller normal
7. FAN SPEED display
9.TEMP button
Used to select your desired temperature.
LOWHI MEDAUTO
12. LOCK display
DRY HEATCOOL
11. SIGNAL SENDING display
13.TEMP display
Remote controller:to display the TEMP. setting.
15. POWER/SOFT display
6.Operation mode display
Parts and Functions
14.TIMER MODE display
OFF:The air conditioner stops operation
after the designed period.
ON:The air conditioner starts operation
after the designed period.
8. DESIGNATED PERIOD diplay
Indicates the period set by
the time setting switches.
10. CODE display
AUTO
H
4
5

«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
Remote controller's operation
When in use, put the signal transmission head directly to the
receiver hole on the indoor unit.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
Don't throw the controller, prevent it from being damaged.
When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals
so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)
Remove the battery cover:
Slightly press " " and push down the cover.
Load the battery:
Be sure that the loading is in line with the" + "/"-"
pole request as illustrated.
Put on the cover again
Confirmation indicator:
In disorderation, reload the batteries or load the new batteries after 6mins.
Note:
Use two new same-typed batteries when loading.
If the remote controller can't run normally or doesn't work at all,
use a sharp pointed item to press the reset key.
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out just need to press reset key.
Power failure resume(please set and apply as necessary)
If sudden power failure occurs, the unit will resume original operation when power is
supplied again.
Note: When sudden power failure happens during unit operation in power failure resume mode, if
the air conditioner is not desired for use in a long period, please shut off the power supply
in case that the unit automatically resume operation when power is re-supplied, or press
ON/OFF to turn off the unit when power resumes.
Parts and Functions

Press MODE button.For each press, operation mode
changes as follows:
Then select COOL or DRY operation
Press TEMP. button
Every time the button is pressed, temp.setting
increase 1 C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1 C,if kept depressed, it will decrease
rapidly
Select a desired temperature.
3.Select temp.setting
Cool/Dry mode Operation
Link with electric power.
The liquid crystal will display the working state of last
time (Except Timer, Power/Soft ).
Operation
Remote Controller
1. Unit start
2. Select operation mode
5. Unit stop
4. Fan speed selection
Press ON/OFF button, the unit stops.
Press ON/OFF on the remote controller, unit start.
Remote controller:
Air conditioner is running under displayed fan speed.
Press FAN button. For each press, fan speed changes
as follows:
Remote controller:
When FAN is set to AUTO,the air conditioner
automatically adjusts the fan speed according to room
temperature.
DRY HEATCOOL
LOWHI MEDAUTO
8

Press MODE button.For each press, operation mode
changes as follows:
Then select HEAT operation
Press TEMP. button
Every time the button is pressed, temp.setting
increase 1 C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1 C,if kept depressed, it will decrease
rapidly
Select a desired temperature.
3.Select temp.setting
DRY HEATCOOL
Heat Operation
Air conditioner is running under displayed fan speed.
Operation
Remote Controller
Link with electric power.
The liquid crystal will display the working state of last
time (Except Timer, Power/Soft airflow).
1. Unit start
2. Select operation mode
Press ON/OFF on the remote controller, unit start.
Remote controller:
5. Unit stop
4. Fan speed selection
Press ON/OFF button, the unit stops.
follows:
Remote controller:
When FAN is set to AUTO,the air conditioner
automatically adjusts the fan speed according to room
temperature.
Press FAN button. For each press. fan speed change as
On cooling only unit, heating mode is not available.
In HEAT mode, warm air will blow out after a short period
of the time due to cold-draft prevention function.
LOWHI MEDAUTO
9