Haier HSU-09LEK03/R2(DB) User manual

Please read this operation manual before using the air conditioner.
Ɣ
Keep this operation manual for future reference.
SPLITTYPEROOMAIRCONDITIONER
OPERATION MANUAL
0010562830
Contents
1
2
5
7
6
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-09LEK03/R2(DB)
HSU-12LEK03/R2(DB)

Outdoor Unit
4
Loading of the battery
1
2
3
4
Parts and Functions
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Remote controller
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Please be subject to the actual produce purchased the
above picture is just from your reference
4
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
Please be subject to the actual produce purchased the
above picture is just from your reference
Air Purifying Filter
(inside)
Inlet
1
Inlet grille
2
Outlet
3
(adjust left and
Vertical blade
right air flow)
4
Display board
Horizontal flap
(adjust up and down air flow.
Don't adjust it manually)
Emergency Switch
6
7
8
5
1
2
3
4
5
6
7
8
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6.TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller appears
abnormal, use a sharp pointed article
to press this button to reset the remote
22. HOUR button
FAN
COOL DRY
Remote
controller
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
9. TURBO button
10. FAN button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. SLEEP button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation
mode
Remote
controller
QUIET TURBO
SLEEP HEALTH
8. Additional functions display
NOTE: Healthy function is not available for some units.
Function: Health--- Healthy airflow
position1 --- Healthy airflow position 2
--- Restore the original flap position---
air airflow --- A-B yard --- Refresh air
(reserved function) --- QUIET ---
Fahrenheit/Celsius mode conversion
Operation
mode AUTO

Operation
Air Flow Direction Adjustment
Base Operation
Remote controller
Emergency operation and test operation
Operation
Mode
Remote
Controller Note
In DRY mode , when room temperature becomes lower
than temp.setting+2oC, unit will run intermittently at LOW
speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool operation according to room
temperature. When FAN is set to AUTO the air conditioner
automatically adjusts the fan speed according to room
temperature.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
below 16oC, do not use it in the normal operation.
Test operation:
Use this switch in the test operation when the room temperature is
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds.After
you hear the "Pi" sound twice, release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
DRY
COOL
AUTO
FAN
Emergency Operation:
Use this operation only when the remote
controller is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which
the start of this operation.
In this operation, the system automatically
selects the operation modes,cooling or fan
or heat, according to the room temperature.
It is not possible to operate in dry mode.
Room
temperature Operation
mode Designated temperature Timer
mode Air flow
ABOVE 23OCCOOLING 26OCNO AUTOMATIC
(cooling only uint)
Room temperature Operation
mode Designated
temperature Timer
mode Air flow
BELOW 23OCFAN 26OCNO AUTOMATIC
means
Pi
Pi Pi
1
3
2
2
Press FAN button
Remote controller:
Press button
Every time the button is pressed,
temp.setting increase 1 C,if kept
o
depressed, it will increase rapidly
Every time the button is pressed,
temp.setting decrease 1 C,if kept
depressed, it will decrease rapidly
Select a desired temperature.
3.Fan function
2.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to
room temperature.
1.Unit start
Press ON/OFF on the remote controller, unit starts.
/
changes as follows:
LOW MED HI AUTO
Display
circulated
For each press button fan speed
o
1.Status display of air flow
COOL/DRY:
Initial state
Press button to enter additional options, when cycle
display to , will flash.And then press enter to
up and down air flow function.
Press button. For each press,changes as follows:
Remote controller:
When restart after remote turning off, the remote controller
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur at
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY mode,otherwise,
condensate water might occur.
air outlet if all vertical louvers are adjusted to left or right.
will automatically return to the previous set swing position.
Note:
Move the vertical blade by a knob on air conditioner to adjust
left and right direction referring to Fig.
2.Left and right air flow adjustment (manual)
3D

Operation
Sleep Operation
2.In AUTO mode
3. In FAN mode
It has no SLEEP function.
up. After the sleeping function is set up, function, the
TIMER machine will be in the state of timing-on, if
the two modes are set up at the same time, either
of their operation ime is ended first,the unit will stop
automatically, and the other mode will be cancelled.
4. When quiet sleeping function is set to 8 hours the
Note to the power failure resume:
press the sleep button ten times in five seconds and
enter function after hearing four sounds. And press
the sleep button ten times within five seconds and
leave this function after hearing two sounds.
quiet sleeping time can not be adjusted.When TIMER
function is set,the quiet sleeping function can't be set
sleeping function will be cancelled; the if user resets
Operation Mode
1. In COOL,DRY mode
SLEEP operation
starts
SLEEP operation
stops
Approx.6hrs
1 hr Rises 1
O
C
Temp.setting Unit stop
In COOL, DRY mode
1 hr
1 hours after SLEEP mode starts,temp.will become
temp.risesby 1 C futher. The unit will run for further
6 hours then stops Temp. is higher than temp.setting
so that room temperature won’t be too low for your
sleep.
O
1 C higher than temp.setting.After another 1 hours,
O
Press button , the remote controller wil show
，and then achieve to the sleep function.
Press again this button , the sleep function
will be cancelled.
Note
When TIMER function is set, the sleeping function can’t
be set up .After the sleeping function is set up,if user
resets TIMER function,the sleeping function will be
cancelled; the machine will be in the state of timing-on.
Power Failure Resume Function
If the unit is started for the first time, the compressor
not start running unless 3 minutes have elapsed.
When the power resumes after power failure, the
unit will run automatically, and 3 minutes later the
compressor starts running.
SLEEP
SLEEP
Note:
During TURBO operation, in rapid COOL mode, the room
will show inhomogeneous temperature distribution. Long
period QUIET operation will cause effect of not too cool
or not too warm.
TURBO/QUIET Operation
(This function is unavailable on some models.)
(1) TURBO Operation
(2) QUIET Operation
When you need rapid heating or cooling, you can use
Press button to enter additional options, when
cycle display to , will flash, and then press
,enter to quiet function. When cancel the function,
please enter additional options again and to cancel
quiet function.
this function. Press TURBO button, the remote controller
will show , and then achieve to the turbo function.
Press again this TURBO button , the turbo function will be
cancelled.
Rises 1
O
C
The unit operates in corresponding sleep mode
corresponding sleep mode adapted to the
automatically selected operation mode.

Operation
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). " "or " "will flash.
3.Press / button to set time.
It can be adjusted within 24 hours.
Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.
Timer On/Off On-Off Operation
Healthy airflow Operation
1.Press to starting
Setting the comfort work conditions.
2.The setting of healthy airflow function
Note:
3.The cancel of the healthy airflow function
Notice: Do not direct the flap by hand. Otherwise, the
grille will run incorrectly. If the grille is not run correctly,
stop for a minute and then start, adjusting by remote
controller.
TIMER OFF-ON
0.5h 0.5h 0.5h 0.5h
Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
After adjust the time,press button and confirm the
time ON or OFF button will not flash any more.
4.Confirm timer setting
5.Cancel timer setting
Press the timer button by times until the time display
eliminated.
Press button to enter additional options,Press this
button continuously , the louvers location will cycle between
in the following three locations, to choose the swing location
what you needed,and then press button to confirm.
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations again,and then press
button to cancel.
Healthy
airflow
upwarder
Healthy
airflow
downwarder
Present
position
Press button to enter additional options, when cycle
display to , will flash,and then press ,enter to
health function. When cancel the function, please enter
additional options again and to cancel health function.
(This function is unavailable on some models.) 1.After setting the healthy airflow function, the position
grill is fixed.
3.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may
occur at the grille .
2.In cooling, it is better to select the mode.
The anion generator in the airconditioner can generate
a lot of anion effectively balance the quantity of
position and anion in the air and also to kill bacteria
and speed up the dust sediment in the room and
finally clean the air in the room.
HEALTH Operation

Maintenance
Setting of proper room
temperature
Close doors and windows
during operation
If the unit is not to be used
for a long time, turn off the
power supply main switch.
Use the timer effectively
Use the louvers effectively
Do not block the air inlet
or outlet
Proper
temperature
During cooling operation
prevent the penetration
of direct sunlight with
curtain or blind
OFF
Remote Controller Indoor Body
1.Open the lnlet Grille
2.Detach the standard air filter
3.Attach Air Purifying Filter
4.Attach the standard air filter
(Necessary installation)
5.Close the Inlet Grille
Close the Grille surely
Slide the knob slightly upward to
release the filter, then withdraw it.
Put air purifying filter appliances into the
right and left filter frames.
Detach old Air Purifying Filter NOTE:
The photocatalyst air purifying filter will be solarized in fixed
time. In normal family, it will be solarized every 6 months.
Prop up the inlet grille by using a
small device named grille-support
ATTENTION:
Please keep the bacteria-killing medium air purifying filter in
avoid long time directly sunshine
when you stop using it,or its ability of sterilization will be
reduced.
The bacteria-killing medium air purifying filter will be used
for a long time,no need for replacement. But in the period
of using them ,you should remove the dust frequently by
which located in the right side of
the indoor unit.
using vacuum cleaner or flaping them lightly,otherwise ,
its performance will be affected.
the cool and dry conditions
For Smart Use of The Air Conditioner
Replacement of Air Purifying Filter
The white side of the photocatalyst air purifying filter
face outside,and the black side face the unit The green
side of the bacteria-killing medium air purifying filter face
outside,and the white side face the unit.
Do not usewater,wipe the controller
with a dry cloth.Do not use glass
cleaner or chemical cloth.
wipe the air conditioner by using a
soft and dry cloth.For serious stains,
use a neutral detergent diluted with
water.Wring the water out of the
cloth before wiping,then wipe off the
detergent completely.
Air Filter cleaning
Open the inlet grille by pulling it upward.
Remove the filter.
Clean the filter.
Attach the filter.
Close the inlet grille.
Push up the filter's center tab slightly until it is
from the stopper, and remove the filter downward.
Use a vacuum cleaner to remove dust, or wash the filter with
water.After washing, dry the filter completely in the shade.
Attach the filter correctly so that the "FRONT" indication
facing to the front.Make sure that the filter is
fixed behind the stopper.If the right
attached correctly, that
Do not use the following for cleaning
Gasoline,benzine, thinner or cleanser
ay damage the coating of the unit. Hot water over 40OC(104OF) may
discoloring or deformation.
Once every
two weeks
mcause
released
is
completely
and left filters are not
may cause defects.

the power supply cord
and so on.
2.Do not install in the place where there is any
possibility of inflammable gas leakage around the unit.
3.Do not get the unit exposed
to vapor or oil steam.
Cautions
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
Connect the earth
cable.
earthing
WARNING
When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.
OFF
Use an exclusive
power source
with a circuit
breaker
ENFORCEMENT
Connect power supply cord
to the outlet completely Use the proper voltage
Do not use power supply
cord in a bundle.
Take care not to damage
the power supply cord.
1.Do not use power supply cord extended
or connected in halfway
STRICT
ENFORCEMENT
STRICT
STRICT
ENFORCEMENT PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
Do not start or stop the
operation by disconnecting
Do not channel the air flow directly
at people, especially at infants or
the aged.
Do not try to repair or
reconstruct by yourself.
Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.
CAUTION
Take fresh air occasionally especially
when gas appliance is running at the
same time.
PROHIBITION STRICT
ENFORCEMENT
Do not operate the switch with
wet hand.
PROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not install the unit near a fireplace
or other heating apparatus.
Check good condition of the installation
stand
Do not pour water onto the unit for
cleaning
PROHIBITION
Do not place animals or plants in
the direct path of the air flow
Do not place any objects on or
climb on the unit.
Do not place flower vase or water
containers on the top of the unit.
Do not insert objects into the air
inlet or outlet.
PROHIBITION
PROHIBITION
PROHIBITION
STRICT
ENFORCEMENT
Check proper installation of the
drainage securely
WARNING

Normal
Performance
inspection
Noise is heard
Phenomenon Cause or check points
The system does not restart
immediately.
Smells are generated.
Mist or steam are blown out.
Multiple
check
Poor cooling
Application temp. range of air conditioner -7oC~43oC.
When unit is stopped, it won't restart
elapsed to protect the system.
When the electric plug is pulled out
and reinserted, the protection circuit
During unit operation or at stop,
a swishing or gurgling noise may
(This noise is generated by
refrigerant flowing in the system.)
During unit operation, a cracking
noise may be heard.This noise is
temperature changes.
Should there be a big noise from
filter may be too dirty.
This is because the system
circulates smells from the interior
During COOL or DRY operation,
This is due to the sudden cooling
Is power plug inserted?
Is there a power failure?
Is fuse blownout?
Is the air filter dirty?
Are there any obstacles before
Is temperature set correctly?
Are there some doors or
Is there any direct sunlight
through the window during the
Are there too much heat sources
or too many people in the room
In dry mode, fan
speed can’t be changed.
In DRY mode, when room
than temp.setting+2oC,unit will
regardless of FAN setting.
Maximum: D.B
10.The appliance must be installed on a strong enough support.
9.Young children should be supervised ensure that they do not
play with the appliance.
8.The appliance is not intended to use by young children or infirm
persons without supervision.
7.The used batteries should be disposed of properly.
6. After installation, the power plug should be easily reached.
5.The wiring method should be in line with the local wiring standard.
3. If the fuse on PC board is broken please change it with a fuse
type T. 3.15A/250V.
11.The wiring diagram is attached inside the machine.
2. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualified
person.
The type of connecting wire is H05RN-F or H07RN-F
The machine is adaptive in following situation
1.Applicable ambient temperature range:
Cooling
Indoor
Outdoor
Maximum: D.B / W.B 32oC/23oC
18oC/14oC
43oC/26oC
18oC
Minimum: D.B / W.B
Minimum: D.B
For: T3
Cooling
Indoor
Outdoor
Maximum: D.B / W.B
Minimum: D.B / W.B
Maximum: D.B / W.B
Minimum: D.B
29
o
C/19
o
C
18
o
C/14
o
C
54
o
C/24
o
C
18
o
C
For: T1
during cooling operation?
cooling operation?(Use curtain)
windows left open?
inlet and outlet?
Normally it should be cleaned
every 15 days.
run intermittently at LOW speed
temperature becomeslower
indoor unit may blow out mist.
of indoor air.
air such as the smell of furniture,
paint, cigarettes.
air flow in unit operation, air
generated by the casing expanding
or shrinking because of
be heard.At first 2-3 minutes after
unit start, this noise is more noticeable.
will work for 3 minutes to protect the
air conditioner.
immediately until 3 minutes have
If the fuse of outdoor unit on PC board is broken, please change
it with the type of T. 25A/250V.
Application temp. range of air conditioner -7oC~54oC.
T1:
T3:
Trouble shooting Cautions
Before asking for service, check the following
first.
4.The distance between the indoor unit and the floor should be
more than 2m.