Haier HW-05C03 User manual

HW-05C03/R1
001056
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait 3 Minutes Before
Restarting
POWER

1
2
3
3
4
4
5
6-7
6
6-7
8-12
9
9-10
11-12
13-14
15
Installing unit into a window
Wall installations

5

2. MODE Set Switch
2-way
airflow
control paneleasy access filters
5. How The Unit Drains
MODEL: HW-05C03/R1
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait 3 Minutes Before
Restarting
POWER

Fig. # 1
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
POWER
6

Also when you shut off the air conditioner wait for 3 minutes
before turning it on again.
CAUTION:
7
1
2
3

8

HW-05C03/R1
320
340
559
316
130
471.5
373
TEMPERATURE
1
2
3
4
10
9
8
7
65
FANONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait3 Minutes Before
Restarting
POWER
9

INNER
SILL
OUTER
SILL
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
WOOD STRIP
MOUNTED ON
TOP OF INNER SILL
WOOD STRIP
FOR BASEPAN
ANGLE
STORM
WINDOW FRAME
25mm MAX.
19mm CLEARANCE
1. This unit is designed for installation in standard double hung windows
with actual opening widths of 559mm to 915mm . The upper and lower
sash must open sufficiently to allow a clear vertical opening of 355mm
from the bottom of the sash to the window stool.
2. If storm window presents interference, fasten a 50mm wide wood
strip(not included) (OUTER SILL) to the inner window sill across the full
width of the sill. The wood strip should be thick enough to raise the
height of the window sill so that the unit can be installed without
interference by the storm window frame (STORM WINDOW FRAME)
or wood strip (OUTDOORS) to help condensation to drain properly to
the outside.
3. Install a second wood strip (approximately 150mm long by 38mm
wide and same thickness as first strip) in the center of the outer sill flush
against the back off the inner sill. This will raise basepan angle .
4. If the distance between STORM WINDOW FRAME and WOOD STRIP
MOUNTED ON TOP OF INNER SILL is more than 25mm, two of wood
strip are not necessary.
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
INNER
SILL
OUTER
SILL
1
Hereinbefore is just for the demonstration,please adjust the data
according to the actual structure and dimension of the window.
10
3
2

11

12
Also the side louvers should not be blocked.
This is to have proper air circulation in and around the compressor. (See fig.#2)

13
The air filter behind the front grille should be checked and
cleaned at least once every 2 weeks or more often if necessary.
To remove:
1. Open the inlet grille downward by pulling out the top of the inlet grille.
2. Remove the air filter from the front grille assembly by pulling the air filter
up slightly.
3. Clean the filter with warm, soapy water below 40oC.
4. Rinse and gently shake the water from the filter and let it dry before replacing
it.
Always use a soft cloth dampened with water or mild soap
and water solution to wipe the front of the cabinet.
To clean the front panels or the cabinet DO NOT use harsh
chemicals, abrasives, ammonia, chlorine, bleach, concentrated
detergents, solvents or metal scouring pads.
DO NOT use your air conditioner without the air filter in place.
Always unplug your air conditioner before cleaning.
TEMPERATURE
PEED
LOW
OFF
POWER
1
2
3
4
10
9
8
7
6
5
FAN ONLY
MIN
COOL MAX
COOL

14

15
(see page 6)