Haier HW-09CV03 User manual

1
2
3
4
This switch controls the preset indoor
temperature to make the air conditioner start or
stop automatically, so as to reduce power
consumption and operate the system both
comfortably and economically.
Operate the switch as follows: Temp.
decreases as the switch is turned form “1” to
“9”. Temp. increases as the switch is turned
from “9” to “1”.
“Test run” mode.
(For model HW-09CV03, HW-12CV03,
HW-09CVA03, HW-12CVA03 only)
When switch set to this position, air-con will
run continuously regardless of temp. setting.
Don’t use test run for normal operation.
The compressor stops running when the set
temperature is reached but the fan continues to
operate to keep an even indoor temperature.
Always turn off the air conditioner and the main power supply before clean the unit.
Switch off the power supply if the unit is not going to be used for a long period of time.
CAUTION
Note:
In cooling mode, after you turn
thermostat switch counter-clockwise,do
not turn it back until at least 3 minutes
have elapsed.Otherwise, the fuse may
blow due to overload.
Do not exceed the selection range.
It is advisable not to keep horizontal flap at downward position for a long time in COOLor FAN
mode,otherwise , condensate water might occur.
Don't move the vertical flap with hand in order to avoid the vertical flap abnormal, using the
AUTO SWING switch to adjust the move of vertical flap.
Cleaning of the
air filter
After unit stops, don't restart it
until 3 min. have elapsed.
Don't be exposed to cold air for
a long time.
Avoid opening doors and windows
unless necessary.
Use curtain or blind
Direct sunlight may reduce cooling
effect, always use window curtain.
Keep heat source away from
air conditioner.
Set temp . a little bit higher
before going to bed.
OK! Enjoy a
3-min nap
Proper
temperature
HW-09CV03 HW-09CVA03
HW-12CV03 HW-12CVA03
HW-18CV03 HW-18CVA03
Please read this operation manual before using the air conditioner
Please keep it attentively
0010556533
OPERATION MANUAL
Applicable ambient temperature range:
OPERATION CONDITIONS
Cooling Indoor Outdoor
Max.Temperture:
Min.Temperture:
D.B D.B
W.B W.B
32 C
o
23 C
o
18 C
o
14 C
o
43 C
o
26 C
o
18 C
o
/
ROOM AIR CONDITIONER
CONTENTS
Safety precautions...................1
Air conditioner operation..........2
Care and Maintenance ............4
Air conditioner installation........5
Troubleshooting.......................7
D.B :Dry Bulb Temperature
W.B :Wet Bulb Temperature
AIR CONDITIONER OPERATION
2CARE AND MAINTENANCE 3
SAFETY PRECAUTION
1
Operation Guide
It is advisable to clean air filter every two weeks for
longer operation.
(You will find how to clean the filter on page 2 .)
Baby has
gone sleep,
better to adjust
suitable temp.
Don't hang clothes in the vicinity
of air inlet. This will decrease
cooling effect and cause abnormal
operation.
Temperature should be set properly
when there are infant,child, the
aged or disabled in the room.
Before operating mode
selection switch, check that if
the air inlet or outlet have been
blocked.
1.Do not install, remove and reinstall the unit yourself. Improper installation may cause leakage, electric
shock or fire. Please engage an authorized dealer or specialist for the installation work.
2.The room air conditioner must be earthed.
3.Do not touch or operate with wet hands.
4.Do not turn on the unit by inserting the power plug. Do not switch off the unit by pulling out the power
plug.
5.Do not insert sticks, fingers or other objects into the unit.
6.If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar
qualified person.
7.After installation, the power plug should be easily reached.
8.The wiring method should be in line with the local wiring standard.
CAUTION
Air filter cleaning
1
Notes
2
Auto swing switch
1
Thermostat switch
2
Mode selection switch
3
Operation panel
COOL
1
3
6
9
Test
run
LO
cool
HI
cool
HI
fan
LO
fan
OFF
Wait 3 minutes before restarting.
Mode selection
OFF ON
Auto swing Temp. setting
HW-09CV03 HW-09CVA03
HW-12CV03 HW-12CVA03
HW-18CV03 HW-18CVA03
Mode selection
LOW
COOL
HIGH
COOL
HIGH
FAN
LOW
FAN
OFF
OFF ON
Auto swing Temp. setting
MIN
COOL
MAX
COOL
1
2
3
4
56
7
8
9
10
WAIT THREE MINUTES BEFORE RESTARTING
When the swith is set to “ON”, vertical louver
will swing from side to side, delivering gentle
air thus making you feel very comfortable.
When it is set to “OFF”, vertical louver will
stop at position.
Mode switch controls the fan motor speed.
Cooling speed or fan speed.
When set to “HI fan”, fan motor runs at high
speed to blow out strong air.
When set to “LO fan”, fan motor runs at low
speed to blow out gentle air.
When set to “HI cool”, air-con will start
cooling at high speed, blowing out strong
air.
When set to “LO cool”, air-con will start
cooling at low speed, blowing out gentle air.
When set to “OFF”, air conditioner stops
running.
When mode selection switch is shifted to “HI
fan” or “LO fan”, air-con will only blow out air
without cooling.While the air conditioner
running, its mode selection shouldn’t be shifted
frequently between “HI fan” and “HI cool”, “LO
fan” and “LO cool”.
HINTS
HINTS
Machine body
Take out the air filter
Clean the filter
When dirt accumulates on air filter, air
circulation will be blocked, which causes
poor cooling. It is advisable to clean air
filter every two weeks for longer operation.
1.Loose the air inlet by pushing
“PUSH” at both edges as
shown.
2.Open the air inlet.
1.Gently flap the dirt off the air filter.
2.Carefully wash air filter in warm water(below 40°C).To
obtain better cleaning effect,soap water or neutral
detergent may be used.
3.Flush air filter carefully with clean water after removing
dirt.Let it dry completely.
PART INDENTIFICATION
Airflow Direction Vane
Air filter cleaning
2Airflow Direction
3
Do not circumgyrate the
front panel any more than
90°to the unit or damage
to the tabs may occur.
CAUTION
Before cleaning, turn off
the power.
Front panel
Air inlet
(indoor side)
Air outlet
(indoor side)
Air inlet
(outdoor side)
Air filter (inside)
Machine body
3.Remove the air filter.
Installation of filter
1.Replacing the air filter.
2.Push the air inlet marked with “PUSH” until you hear a
click.
OPENCLOSE
The ventilation lever must be
CLOSE position in order to
maintain the best cooling
conditions. When fresh air is
necessary in the room, set the
ventilation lever to the OPEN
position. The damper is
opened and room air is
exhausted.
(For model HW-18CV03
HW-18CVA03 only)
Ventilation
1
The horizontal air direction is
adjusted by setting the
AUTO SWING switch to the
ON position.
The Vertical Airflow Direction
Vane is manually controlled
by positioning the vane to
discharge the air upward,
downward or straight out.
PUSH
PUSH
Air filter(inside)
COOL
1
3
6
9
Test
run
LO
cool
HI
cool
HI
fan
LO
fan
OFF
Wait3 minutes before restarting.
Modeselection
OFF ON
Autoswing Temp.setting

5
6
7
8
SELECTION OF THE INSTALLATION POSITION
THE ENCLOSED ACCESSORIES OF THE CONDITIONER
INSTALLATION PROCEDURES
PREPARATIONS BEFORE INSTALLATION
AIR CONDITIONER INSTALLATION
4
TROUBLESHOOTING
5
Before calling for service.
Check the following points before calling for repairs or service.
Fig.1
Wall
Water outlet flexible
pipe(provide by user)
1. Fix the prefabricated iron frame to stable position by expansible screws.
2. Put the whole machine with all the accessories installed, on
the iron frame. If there's water outlet flexible pipe, lead it to
needed position(see Fig.1).
3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to
prevent the entering of outer noise and the leaking of the coolness.
5. After installation of the conditioner, insert the power plug into the outlet and perform test-run.
Make the wall hole or window hole (see Fig.1)
Fig. 1
A
B
Width of the wall
Iron frame
1,The air-conditioner is better installed in shadow or in a place
with short period of sunshine. In case the air-conditioner is
installed at the point exposed directly to the sunshine, it should
be protected from the direct sunlight as possible in order to
avoid the long time of direct sunlight otherwise its performance
will be lowered. (As illustrated in Fig. 1).
2. For the convenience of operation, it is
recommended that air-conditioner be installed at
least at the height of 760-1300 mm above the
floor and no obstacles before it for a free airflow.
3.The shutters at both sides and the top of
air-conditioner should be protruded outdoors free
from being blocked by wall, window,ect.
4.The back of air-conditioner should be kept over
500mm from the obstacles (for example, wall,
etc.) (As illustrated in Fig. 2).
5.To have an efficient drainage, the back part of
the air-conditioner should be inclined downward
by 5-10mm (As illustrated in Fig. 3).
Install air-con at a place strong enough to support the unit.
Leave enough space around air inlet and outlet for better circulation.
Avoid places where flammable gas leaks.
Problems may occur if unit is installed in the following places:
Place where oil exists in the air including engine oil or seaside with
salt breeze blows and hot spring area with sulphurous gas in the air.
For longer and trouble-free operation of the unit, pay special attention to the following:
NOTES:
(ONLY FOR REFERANCE)
cover
support
fig.1
>500mm
fig.2
5-10mm
fig.3
Cautions
Power cord: Be sure to use the exclusive power cord.
Always use at the rated voltage and with specfic air conditioning circuit
Change installation place: If air-con need to be changed to another
place please contact the dealer, who sold you the unit.
1.Take out the conditioner and accessories from the package .
2.Disposal of the condensed water.
Prepare unit for installation:
MODEL A B
420mm 580mm
355mm 535mm
HW-09CV03
HW-12CV03
HW-09CVA03
HW-12CVA03
HW-18CV03
HW-18CVA03
If problems can not be solved please pull out power plug and contact
your dealer.
Is plug firmly inserted?
Is there power failure?
Readjust power supply
Is thermostat switch
wrongly adjusted?
Readjust the thermostat.
Is there any direct
sunlight in the room?
Use curtain or blind.
Are doors or windows
left open? Shut doors and windows.
Are there any obstacles
blocking air inlet and
outlet?
Remove the obstacles.
Is there too much heat
source in the room?
Is air filter clogged?
Clean it.
Remove the heat source
Does fuse get burned?
Phenomenon SolutionCause or check points
Replace fuse.
Switch on the machine but it
does not work immediately.
If the machine is started after stop,it will need about 3 minutes to
re-start so as to prevent the fuse from break.
Switch on the machine but it
does not work.
The cooling effect is not good.
NOTE:Your model will have one Drain elbow of the above two, not both.
Manual
OR
Rubber lid Screw
Drain elbow
(with seal ring)
Name
Figure
Quantity 1 1 1 1
Block the bottom plate hole of the conditioner
with rubber lid, install drain elbow on the
back hole and let the condensing water flow from
the back hole of the conditioner. (See Fig.1 ) In
this method, the accumulated condensed water
in the bottom plate is hit by the fan onto the heat
exchanger, and evaporated and blown out
from the machine. It can cool the heat
exchanger adiator more quickly, and improve
the energy efficiency of the conditioner. But the
hitting noise by the fan at the outdoor side is
relatively large.
Rubber lid
Fig.1
Drain elbow
NOTE:
When install drain elbow, adjust the direction of the
drain elbow to make it be in line with the hole in
the rear of unit; Insert the drain elbow into hole
and twist 90°.
NOTE:
For some models your Drain elbow may be the
same as Fig.2.
Rubber lid
Fig.2
Drain elbow
4. Open the Air inlet geille ,fix the front panel to the chassis firmly with the accessorial screw.(see
Fig.2 or Fig.3)
(NOTE:Your model will be the same as one of the right two illustrations,not both.)
Fig.3Fig.2