Haier HR-SC User manual

HR-SC
OPERATION INSTRUCTIONS
Haier solar station
OPERATION INSTRUCTIONS
Haier solar station
HCSOL HWT
PREINT
T-DISP
SET REGMODE
Read the operation instruction
carefully before use.
Ensure good storage of the operation
instruction for late consultation.
ON/OFF
MPa
Safety information (read it before use)..... 2
Installation introduction..............3
Installation cautions.......................3
Installation of the solar station . . 4
Circuit connection...........................6
Installation of expansion tank
and priming valve ..........................7
Priming antifreeze...........................8
Directions for use .........................9
Directions for buttons and
indication lamps..............................9
Operation methods........................11
Electric principle diagram, technical
data and packing sheet................14
Electric principle diagram ............14
Technical data...................................14
Packing sheet....................................14
Questions and answers ................15
CSH09J0455.indd 1 11/6/2009 4:08:16 PM

2Haier solar station
Safety information (read it before use)
Symbol indications:
Be prohibited
Actions must be prohibited.
Notice
Items must be noticed.
Cautions
Actions must be implemented.
Notice
• ThematchingcontrolledauxiliaryelectricheatingpowerofSolarpowerstationshallnotbe
higher than 2,600W/230V .
Be prohibited
• Itisprohibitedto insert orpullout power plugwithwethandsfor the potential riskof
electric shock.
• Avoiddirectshoweronthesolarstation.Ifitisshoweredbyaccidental,itmustbeinspected
byprofessionalpersonnelbeforeuse.
• Donotusewornpowerwireandsockets.Cleanplugandsocketandremovetheduston
theplugandsockettimely,orelectricshock,shortcircuit,re,etc.mayoccur.
• Disassemble,repair,maintainandreconstructsolarstationbylaymanisprohibited.
• Childrenshouldbesupervisedtoensurethattheydonotplaywiththeappliance.
Cautions
• Nootherthan 230V/50Hzseparatesocketcan beused(multiple-usesocketisprohibited
for use).
• Reliableearthingmustbeensured.Itisprohibitedtousesolarstationwithoutreliable
earthing.
• Ifunusual indicationsorscorchedsmellisfoundinthesolarstation,turn offthepower
immediatelyandcontactaftersalesector.
• Beforeuse,ensurethatalltheconnectioncomponentsofthepipesaresealedwithout
leakage.
• Ifthesupplycordisdamaged,itmustbereplacedbythemanufacturer,itsserviceagentor
similarlyqualifiedpersonsinordertoavoidahazard.
• Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysical,
sensoryormentalcapabilities,orlackofexperienceandknowledge,unlesstheyhavebeen
givensupervisionorinstructionconcerninguse oftheapplianceby apersonresponsible
fortheirsafety.
CSH09J0455.indd 2 11/6/2009 4:08:17 PM

Haier solar station
3
Notice
Installation introduction
Installation cautions
• Whensolarstationisconnectedforsealing,excessivestrengthmustbeavoided,
orcomponentsmaybedamaged.
• Duringinstallation,solarstationcannotbeinvertedlyplacedandrotationaxle
ofinternalwaterpumpcannotbeverticaltotheground.
• Solarstationcannotbeinstalledintheshowerscopeoftheshowernozzle.
• Internalwaterpumpandcopperhosecouplingofthesolarstationmustnotbe
installedordisassembledbyyourself,oritmayleadtoliquidleakagerisk.
• Donotputotheritemsonthesolarstation.
• Solarstation,primingvalveandexpansiontankmustbeinstalledonthe
circulationoutletpipeofthewaterstoragetank.
• InpipeinsulationworkspecialinsulationmaterialsofHaiermustbeused.
• Solarstationmustbeawayformstrongdisturbingresource(voltage
equipments,communicationequipments,etc.).
• Afteraddingenoughantifreeze,closeinletandoutletoftheprimingvalveand
tighten the nut.
• TheantifreezeusedintheCirculationPipemustbeinconformitytolocalsafety
andenvironmentalprotectionstandardsorlaws.
• TheantifreezemustbeprimedbythequaliedtechnicianofHaier.
• Thedisposaloftheantifreezemustbeinconformitytolocalsafetyand
environmentalprotectionlaws.
• Theantifreezemayevaporable,ammableandtoxic.Ifndleakageofit,contact
thelocalafter-salesectorsimmediately.Ifdrinkorsuckitbyaccident,contact
themedicalinstitutionandseethedoctorimmediately.Iftheskincontactsthe
antifreezeaccidently,washitawayandcontactthemedicalinstitutionandsee
thedoctorimmediately.
Be prohibited
Cautions
Thesolarstationdoesn'tprovidewaterpressureprotectivedevices,heating
elementandheatingelementoverheatingprotectivedevices(thermalcut-out).
Thoseshallbeinsidethewaterstoragetank.Theirsaftyandinstallationshall
beinconformitytolocalsaftystandands.Theheatingelementoverheating
protectivedevices(thermalcut--out)shallprovideall-poledisconnection.
Afterpurchasingsolarstation,pleasecontactlocalafter-salesectors,then
thequalifiedtechnicianwillvisityouforinstallation.Installationbyyourselfis
prohibited.
CSH09J0455.indd 3 11/6/2009 4:08:18 PM

4Haier solar station
Installation introduction
Installation of the solar station
1
2
3
4
Beforeinstallation,determinethespecificinstallationpositionaccordingtothe
requirementsofuser.
Accordingtothepositionsanddistanceofthehangerholesonthebackofsolarstation,drill
twoholesinthewallwithpercussiondrill.Theholeis70mmindepthand9mmindiameter.
Thenfixthehangeronthewallwithtwoexpansionbolts.
Alignthehangerholesonthebackofsolarstationtothehookonthehangerandhangthe
solar station on the hanger.
Screwoffboltsonthebottomshellofsolarstation,openitsfrontshellandconnectitto
theheatcirculationsystem(alltheinletandoutletventsofsolarstationareG1/2”female
standard thread).
Notice
Installationpositiononthewallofinstallationhangerofsolarstationmustbefixed
properlyandwallsupportingloadmustbetwotimesofweightsofsolarstation.
The hanger holes on
the back of solar station
Hanger of
solar station
Small expansion bolt
CSH09J0455.indd 4 11/6/2009 4:08:18 PM

Haier solar station
5
Liquid inlet of
solar collector
Circulation
inlet tube
Plate solar collector
( The components other than solar station is only for reference)
Temperature
sensor wire of
water storage tank
Expansiontank
Safety valve
Priming valve
Priming outlet
Solar station
Priming inlet
Circulation liquid inlet
of water storage tank
Circulation liquid outlet
of water storage tank
Outfall
outdoor
indoor
Check valve
Circulation
output tube
Solar collector temperature
sensor wire
Liquid outlet of
solar collector
Blind tube for
measuring
temperature
Water storage tank
HCSOLH WT
PREINT
T-DISP
ON/OFFSET REG MODE
MPa
Schematic diagram of solar hot water supply system

Installation introduction
Notice
Theverticalheightbetweensolarstationandcollectorshouldnotbegreater
than 10m.
CSH09J0455.indd 5 11/6/2009 4:08:19 PM

6Haier solar station
Notice
•
Thenominalcross-sectionalareaofthewiresshallnotlessthan1.5mm
2
.
Conductorsidentifiedbythecolourcombinationgreen/yellowshallonlybe
used for grounding conductors
•
Thewiresshallprovidenon-detachableliningornon-detachablebushing.
•
Thewiresshallbeprotectedsothattheydonotcomeintocontactwithburrs,
coolingfinsorsimilaredgeswhichmaycausedamagetotheirinsulation.
•
Thewiresshallbeprotectedsothattheydonotcomeintocontactwithhot
surface,wet,orsignificantamountsofultravioletradiationexceptthewiresare
suitable for the conditions.
Circuit connection
Screwoffboltsonthebottomshellofsolarstation,openitsfrontshellandconnectthecircuit
asshowninthediagram.
Circuit connection of water storage tank

2
3
4
1
Solar collector
sensor interface
Relay output
L end
Wire interface
of water pump
Relay output
N end
Relay output
N label
Water storage tank
sensor interface
Signal wire interface
of Display board
Creepage detection
coil interface
Clamp for holding
the wire
Earth plate
Schematic diagram of power
board interface of solar station.
Installation introduction
ConnectrespectivelyLend(brown)andNend(blue)ofwireofwaterstoragetankwithL
endandNendofrelay.(NlabelofrelayrepresentstheNelectrodeofpower)
Connecttemperaturesensorofwaterstoragetankwithcorrespondinginterfaceonthe
powerplate.Insertproperly.
Fixthegroundingwireofwaterstoragetankonthegroundingplateofsolarstationwith
grounding bolts.
Disassemblewireclampandfixandpresswireconnectionofwaterstoragetank.
CSH09J0455.indd 6 11/6/2009 4:08:19 PM

Haier solar station
7
Installation introduction
Connection of solar collector temperature sensor

Findsolarcollectortemperaturesensoronthecorrespondinginterfaceonthepowerplate.
Cutitatthepositionwhereis150mmawayfromtheterminalandstripthewire.(connect
anotherleadaccordingtotheactualinstallationdistancebetweensolarcollectorandsolar
station.Andtheleaddimensionsshallbe:2XAWG24(2X0.2mm2) and it must be resistant to
the temperature above 80°C.)Sticktheconnectionwiththeinsulatingtape.
Place the sensor probe into the blind pipe at the outlet vent of solar collector and insert
ittothebottomtoensurereliablecontactwiththemeasuredpoint.Bandthesensor
wirealongthepipe.Anddisconnectedpointsofleadmustbeavoidedtobeinoutdoor
environment to prevent corrosion and oxidation due to rain.
2
3
1


Schematic diagram of wiring position of solar collector temperature sensor (unit: mm)
cut off connection here
Installprimingvalve(notprovidedwiththeequipments)attheproperpositionofthe
upperendofwaterpumpconnectiontubeofsolarstation.Thevalvehasnodirectionality.
Buttheinstallationspacemustbeconvenientforlatepriming.
Installoneteeattheoutletoftheprimingvalve.Oneendofteeisconnectedwith
circulationliquidoutputtubeandanotherendisconnectedwithexpansiontank.
Afterdeterminationofitsposition,drilltwoholesinthewallwithpercussiondrill.The
holeis70mmindepthand9mmindiameter.Thenfixexpansiontankonthewallwithtwo
expansion bolts and corresponding fixing strap.
1
2
3
Installation of expansion tank and priming valve
Notice
Priming valve and expansion tank are both installed on the corresponding tubes at the
liquidoutletofwaterstoragetank.
CSH09J0455.indd 7 11/6/2009 4:08:20 PM

8Haier solar station
Installation introduction
Screwofftheprimingventcapofprimingvalve,closethebiggercheckvalveinthemiddle
ofprimingvalve(whentwobladesonthevalvehandleisverticaltoaxleofvalve,itis
closed)andopenanothertwosmallercheckvalves.
Connecttheoutputofprimingequipmentwithonepriminginletandensuretheflowing
directionisthesamewithinstallationdirectionofcheckvalve.ThenConnectanother
primingoutputwithreturninginletofprimingequipment.Starttheprimingequipmentfor
priming.
Observethereturnedantifreezeuntiluniformreturnedflowandnobubbleisrealized.At
firstclosethecheckvalveconnectedtoreturninginletofprimingequipment,thenthe
checkvalveconnectedtooutletofprimingequipment,andopenthebiggercheckvalvein
themiddleofprimingvalve.Disassembletheprimingequipment.
1
2
3
Priming antifreeze
Notice
Afterpriming,put3/4fibregasketinthepriminginletcapandtightenittopreventthe
leakage of antifreeze.
CSH09J0455.indd 8 11/6/2009 4:08:20 PM

Haier solar station
9
Directions for use
 Aftertheinstallationofallthetubesandwiring,ensurethatwaterstoragetankisfullofwater
andthatsolarcollectorcirculationsystemisfullofcirculationmediawithoutleakage,then
connectthepowerofsolarstation.
 Afterconnectingthepower,solarstationwillstartforautoinspection,thendisplayplateand
indicationlightsarelightedupfor2seconds,restoretonormaldisplay.Thedefaultworking
mode is solar heating mode.
:ON/OFF :SET :REG :MODE
 Press the button for starting and
another press on the button for
closing. When fault codes occur, press
thebuttonforrestorationdisplay.
 When pressing the button on
mode,thesystemwillbeswitched
betweenthefourmodes:solar
heating, instant heating, presetted
heating and intelligent heating. At
the same time, indication light of
corresponding mode is lighted up.
2-secondpauseautomaticallyconfirms
the mode and then enter the mode.
 Press the button , and press the
button to adjust the corresponding
parameters in 6 seconds.
 Press the button for more than
onesecond,thevaluewillincreaseby
3 jump per second.
 Afterthesetting,pressthebutton
forconfirmationordonotpressany
 buttonsfor6seconds,thesystemwillautomaticallyconfirmit.
 Afterpressingthebutton to turn off the solar station, temperature indication lights
ofwaterstoragetankandsolarcollectorandtemperatureindicatorarestillinnormal
operation;otherdisplayplatesandindicationlightwillbeturnedoff.Andsolarcollection
functionisstillinoperationandelectricheatingwillbeclosed.
Directions for buttons and indication lamps
AB
HCSOLH WT
PRE INT
T-DISP
ON/OFFSET REGMODE
CSH09J0455.indd 9 11/6/2009 4:08:21 PM

10 Haier solar station
Directions for use
Solar energy indication light (green)

Whileitislightedup,itisindicatedthatwaterheaterisinsolarenergyheatingworking
mode.
Instant heating indication light (green/red)

Whilethegreenlightison,itisindicatedthatwaterheaterisininstantheatingworking
mode.Whiletheredlightison,itisindicatedthatwaterheaterstartselectricheating
workingmode.(whenthetemperatureisheatedtothesetvalue,workingmodewillbe
automaticallyswitchedtosolarheatingmodefrominstantheatingmode.Atthesametime
heating indication light is off and solar indication light is on.)
Presetted heating indication light (green/red)

Whilethegreenlightison,itisindicatedthatwaterheaterisinpresettedheatingworking
mode.Whiletheredlightison,itisindicatedthatwaterheaterstartselectricheating
workingmode.(whenthetemperatureisheatedtothesetvalue,indicationlightturns
green.)
Intelligent heating indication light (green/red)

Whilethegreenlightison,itisindicatedthatwaterheaterisinintelligentheatingworking
mode.Whiletheredlightison,itisindicatedthatwaterheaterstartselectricheating
workingmode.(whenthetemperatureisheatedtothesetvalue,indicationlightturns
green.)
Temperature indication light of water storage tank (yellow)

Whileitislightedup,itisindicatedthattemperaturedisplayedintemperaturedisplaying
zoneiscurrenttemperatureofwaterstoragetank.
Temperature indication light of solar collector (red)

Whileitislightedup,itisindicatedthattemperaturedisplayedintemperaturedisplaying
zoneiscurrentoutputwatertemperatureofsolarcollector.
Clock time display/ parameter setting display (green) ( A and B)

Innormalstateitdisplaycurrenttimesetbytheuser,andtheclockcanberesetonlyunder
thesolarenergyheatingmode(greenindicationlightofsolarenergyison).DifferentMode
SettingswilldisplayCorrespondingparameters.
Temperature indicator (green)

Displaycurrenttemperatureofwaterstoragetankandsolarcollectorinturn.
CSH09J0455.indd 10 11/6/2009 4:08:21 PM