Halsey Taylor HAC-4F User manual

92874C (Rev.A)
Glass Filler Plumbing Kit
Model: 73-42485-51-550
HAC-4F HAC-8F
HAC-4FS HAC-FS
HalseyTaylorInstructionManual
WARNING
Toavoidtheriskofelectricalshock,personalinjury,ordeath,disconnectpowerandwater
suppliesbeforeinstallingthisplumbingkit.
CAUTION
Toavoidpropertydamage,personalinjury,and voiding yourwarranty:
*have an authorizedpersoninstallyour plumbing kit
*make sure you read,understand,andfollow the attached instructions
*wearprotectiontoprotectyourselffromsharpedges
*wearsafetygogglestoprotect your eyes from water under pressure and other
projectiles
PARTS LIST
Refertothepartslisttomakesureyoureceivedallplumbing kit parts. If any parts are
missing,contactyourHalseyTaylordealer.
DESCRIPTION
100322740560
50090C
50279C
60119C
62296C
70682C
70683C
1
2
3
4
5
6
7
PART NO.
GASKET-BLACK(QTYOF4)
INSULATION-ARMAFLEX
TAPE-ARMAFLEXINSULATING
TUBE-CU1/4X5.00"
ASSY-BUBBLERTUBE(QTYOF2)
FITTING-TEE1/4
FITTING-UNION1/4
ITEM NO.
PARTS LIST
REQUIRED TOOLS
Youwillneedthe following toolstoinstallyourplumbingkit:
-flatbladescrewdriver
-adjustable wrench
-tubing cutter
-phillipsscrewdriver
-5/16"nut driver or socket

92874C (Rev. A) PAGE 2
REMOVE THE FRONT PANEL AND BASIN
1. Disconnect the electric power and shut off the cold water supply. Press the push bar to relieve any residual
water pressure.
2.Removethe fourfrontpanel screwsandremove thefrontpanel.
3.Carefullyremove the strainerbyusing needle nosepliers.
4.Usingneedlenose pliers, turnthedrain plug counterclockwise andremovethe plug andgasket.Savethe
gasket - it will be used again when unit is re-assembled.
5.Removebubbler by turningcounterclockwise.Discard gasket.
6.Removethe eight basinmountingscrews and removethebasin.

92874C (Rev.A)
PAGE 3
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH PUSH IN COLLET TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OFQUICK CONNECTFITTINGS
INSTALLING GLASS FILLER PLUMBING
The plumbing in your water cooler should look like the illustration shown in Fig.1 at the bottom of this page.
Use the following instructions to install the glass filler in your cooler.
IMPORTANT NOTE:INLET SIDEOF REGULATORHOLDER WAS CHANGEDIN EARLY1997.MAKE
NOTE OF THIS LOCATION ON YOUR UNIT BEFORE CUTTINGANYTUBES!AFTER THE INLET IS
LOCATED, READOVERAND USETHE FOLLOWINGDIAGRAMSASAREFERENCETO
FAMILIARIZE YOURSELF WITH THE TUBES THATARE TO BE CUTAND WHERE THEYARE TO
BE CUT. MAKE SURE THAT POWER AND WATER SUPPLIES ARE OFF BEFORE DOINGANY
WORK ON UNIT.
Fig. 1
1.Disconnectwaterinlet line atregulatorholder.
2. Using a tubing cutter, cut water inlet line as shown (approximately 1-1/2" from bend). Deburr cut tube end.
3. Disconnect water inlet line to tank at the regulator holder.
4. Using a tubing cutter, cut water outlet line on side of joint as shown - remove and discard the bubler tube
assy and armaflex. Deburr cut tube end.
Fig. 2
1. Connect water inlet line to 1/4" union.
2. Route water inlet line to tank approximately as shown and connect to 1/4" union.
3.Connectnew 5" tubetoregulatorholder and place4"of armaflex overtube.
Fig. 3
1. Connect 1/4" tee to the end of the 5" tube.
2. Place 14" of armaflex over water outlet line and route approximately as shown - connect to 1/4" tee.
3. Place 16" of armaflex over glass filler tube assy - connect to other side of 1/4" tee - route approximately
as shown.
4.Place16" of armaflexovernewbubbler tube assyandconnect to regulatorholder-route approximately
as shown.
5. Go to page 4 for instructions on finishing the installation.
7
4
5
56
Fig. 1 Fig. 2 Fig. 3

92874C (Rev. A) PAGE 4
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
2222CAMDEN COURT
OAKBROOK,IL60523
630.574.3500
PRINTEDINU.S.A.
FINISHING THE INSTALLATION
1. Verify that the plumbing is connected as shown in Fig.3 on page 3.
2. Wrap all exposed copper tubing with the foam tube supplied with the kit.
CAUTION!
Toavoidwaterdamage, neverre-useold bubblergaskets.
3. Install one black gasket provided with the kit on each nipple of the bubbler tube assy's. One assy is for
the glass filler and one is for the bubbler.
4. Remove the glass filler plug frm the basin.
5. Align the bubbler tube assy's and the drain with the knockouts in the basin and install the basin using the
eight mounting screws.
NOTE: Be careful not to kink the tubing.
6. Install the bubbler using a new black gasket from the kit.
7. Install the glass filler using a new black gasket from the kit.
8. Install the drain plug by turning it clockwise with the needle nose pliers.
9. Snap the strainer into place.
10. Turn on the cold water supply and check for leaks. Repair any leaks that are found.
11. Reconnecttheelctricpower.
12.Installthefront panel using the frontpanelmountingscrews.