Hama EWS-152 User manual

e
1 00
123126
®
THE SMART SOLUTION
Weather Station EWS-152
Wetterstation
Operating Instructions
Bedienungsanleitung
Mode d'emploi
Instrucciones de uso
Gebruiksaanwijzing
Istruzioni per l'uso
Οδηγίες χρήσης
Instrukcja obstugi
uv
EET]
Návod na pouäitie
Manual de instrucóes
A
| © |
23126man de en el es frit pl ru skindd 2 30.10.14 10:2

|
e
23126man de en el es fr it pl ru skindd 3 30.10.14 10:2

e
23126man de en el es fr it pl ru skindd 4 30.10.14 10:2

©
Operating instruction
Controls and Displays
A Base station
молаш =
8.
9
10.
Outdoor temperature
Battery symbol
Room temperature
Time
Summer time
Wireless symbol
^ button = Increases the current setting/Toggles 12/24 hour format/Manual
search for signal from the measuring station
MODE button = Settings/Confirms the setting
v button = Decreases the current setting/Toggles between °C and °F/Activates/
deactivates manual radio signal reception
Battery compartment
B Measuring station
11.
12.
e 13.
Transmission indicator lamp
Opening for wall mounting
Battery compartment
Thank you for choosing a Hama product
Take your time and read the following instructions and information completely. Please
e
keep these instructions in a safe place for future reference. If you sell the device, please
pass these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
This symbol is used to indicate safety instructions or to draw your attention to specific
hazards and risks.
e
23126man de en el es fr it pl ru skindd 2 30.10.14 10:2

This symbol is used to indicate additional information or important notes.
. Package Contents
Weather Station EWS-152
(base station for indoor/outdoor measuring station)
4 AAA batteries
These operating instructions
. Safety Instructions
The product is intended for private, non-commercial use only.
Do not operate the product outside the power limits given in the specifications.
Do not use the product in moist environments and avoid splashes
Do not use the product in the immediate vicinity of heaters or other heat sources
or in direct sunlight.
Do not use the product in areas where the use of electronic devices is not permitted e
Do not place the product near interference fields, metal frames, computers, TVs,
etc. Electronic devices and window frames can negatively affect the product's
functionality.
Do not drop the product and do not expose it to any major shocks.
Do not open the device or continue to operate it if it becomes damaged.
Do not attempt to service or repair the product yourself. Leave any and all service
work to qualified experts.
Keep the packaging material out of the reach of children due to the risk of
suffocation.
Dispose of packaging material immediately according to locally applicable
regulations.
Do not modify the product in any way. Doing so voids the warranty.
e
23126man de en el es fr it pl ru skindd 3 30.10.14 10:2

* Immediately remove and dispose of dead batteries from the product.
* Only use batteries (or rechargeable batteries) that match the specified type.
+ Do not mix old and new batteries or batteries of a different type or make.
* When inserting batteries, note the correct polarity (+ and - markings) and
insert the batteries accordingly. Failure to do so could result in the batteries
leaking or exploding.
* Do not charge batteries.
Keep batteries out of the reach of children.
.
4. Getting Started
4.1. Measuring station
* Open the battery compartment (13) and insert two AAA batteries with the correct
polarity. Close the battery compartment.
o "πα ©
Before use, ensure you insert the batteries in the measuring station first and then
in the base station.
4.2. Base station
* Open the battery compartment (10) and insert two AAA batteries with the correct
polarity. Close the battery compartment.
e
23126man de en el es fr it pl ru skindd 4 30.10.14 10:2

5. Installation
* We recommend initially placing the base and measuring stations in the
intended locations without installing them and making all the settings described
in 6. Operating — to do
+ Only install the stations once the appropriate settings have been made and a
stable wireless connection is established between the stations.
* The wireless transmission range between the measuring and base stations is up
to 30 m in open spaces.
Before installation, ensure that wireless transmission will not be disrupted by
interference or obstacles like buildings, trees, vehicles, high-voltage lines, etc.
Before the final installation, ensure that there is sufficient reception between the
intended installation locations.
When installing the measuring station, ensure that it is protected from direct
sunlight and rain.
The international standard height for measuring air temperature is 1.25 m (4
ft) above ground.
+ Buy special or suitable installation material from a specialised dealer for
wall-mounting.
* Ensure that no faulty or damaged parts are installed.
+ Never apply force during installation. This could damage the product.
Before installation, ensure that the chosen wall is suitable for the weight to be
installation, and make sure that there are no electrical wires, water, gas or other
lines at the installation site on the wall.
e
e
23126man de en el es fr it pl ru skindd 5 30.10.14 10:2

e
5.1. Base station
* Usethe base to position the base station on a level surface.
5.2. Measuring station
* You can also position the measuring station on a level outdoor surface.
* We recommend installing the measuring station securely on an outdoor wall using
the opening (12). Install an anchor, screw, nail, etc. in the wall of your choice
* Hang up the base/measuring station using the opening intended for this purpose
6. Operation
Hold down the « button (7) or the w button (9) to select values faster.
6.1. Connection to the measuring station
+ After you insert the batteries, the base station automatically searches for а
connection to the measuring station and performs initial setup.
* Initial setup takes approx. 3 minutes.
* Do not press any buttons during setup. Otherwise, values may not be
transmitted correctly and there is a risk of value errors and inaccuracies.
+ The setup process is completed when the indoor (3) and outdoor (1)
measurement data is displayed.
* If the base station still does not receive a signal from the measuring station , press
and hold the « button (7) for approx. 3 seconds to start the manual search for
the signal.
e
23126man de en el es fr it pl ru skindd 6 30.10.14 10:2

e
6.2. Basic and manual settings
Automatic setting using the DCF signal
+ After the base station is switched on for the first time and successful transmission
is established between the base station and the measuring station, the clock will
automaticaly search for a DCF signal. During the search, the wireless symbol (6)
will flash.
Active
Successful — signal is being received
Deactivated ©
+ If the station still does not receive a signal, press and hold the w button (9) for
approx. 3 seconds to start the manual search for the DCF signal. The wireless
symbol (6) will start to flash
* The search process takes about 7 minutes, If the search fails, it ends and is
repeated at the next clock hour. The wireless symbol (6) will go out.
+ Inthe meantime you can, however, set the time and the date manually.
* The clock automatically continues to search for the DCF signal on a daily basis
(between 1:00 a.m. and 3:00 a.m.). If the signal is received successfully, the
manually-set time and date are overwritten.
©
23126man de en el es frit pl ru skindd 7 30.10.14 10:2

* The clock automatically switches to summer time. $ appears on the display as
long as summer time is activated.
* Press and hold the w button (9) again for approx. 3 seconds to stop the manual
search.
Manually setting the date/time
+ Press and hold the w button (9) for approx. 3 seconds to stop the search for the
DCF signal. The wireless symbol (6) goes out and you can set the time manually.
+ Press and hold the MODE button (8) for approx. 3 seconds to start manually setting
the date/time.
+ Set the following information in the order listed:
* Time zone (difference in hours), hour, minute.
+ To select individual values, press the « button (7) or the w button (9) and confirm
each selection by pressing the MODE button (8)
e + Ifyou do not make an entry for 20 seconds, you automatically exit setup mode e
+ The DCF signal can be received over long distances, but always transmits the
current Central European Time in Germany. Make sure you account for the time
difference in countries with another time zone.
+ Ifyou are in Moscow, the time is 3 hours later than in Germany. This means that
you should set +3 for the time zone. The clock then automatically sets the time
to 3 hours after the DCF signal received or relative to the manually set time.
Celsius/Fahrenheit
* Press the w button (8) to switch between °C and °F for the temperature display.
12/24 hour format
+ Press the a button (7) to switch the time between the 12 and 24 hour format.
e
23126man de en el es fr it pl ru skindd 8 30.10.14 10:2