HAMPTON BAY Largo User manual

Largo
Largo
1
22
48
705 544
707 608
635 289
635 412
998 418
560 459
S/O
S/O
S/O

48” Largo
Ceiling Fan by Hampton Bay
Accu-Arm™ for Accurate
and Easy Installation
Indoor/Outdoor Use
3-Speed Reverse Function for
Year-Round Comfort and Savings
Tri-Mount Installation
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
Please reference your SKU (705 544 gilded iron, 635 289 matte white, 998 418 weathered zinc)
or UPC (082392 266844 gilded iron, 082392 266820 matte white, 082392 266851 weathered zinc).
Thank you for purchasing this Hampton Bay ceiling
fan. This product has been manufactured with the
highest standards of safety and quality. The nish
of this fan is weather resistant, but over time will
naturally weather and fade.
Safety Rules .................................. 1
Unpacking Your Fan ................... 2
Installing Your Fan...................... 3
Operating Your Fan .................... 9
Care of Your Fan ......................... 10
Troubleshooting ........................... 10
Specications ................................ 11
Warranty Information................. 12
Table of Contents
UL Model No. 48-LG

Safety Rules .................................. 1
Unpacking Your Fan ................... 2
Installing Your Fan...................... 3
Operating Your Fan .................... 9
Care of Your Fan ......................... 10
Troubleshooting ........................... 10
Specications ................................ 11
Warranty Information................. 12
1. To reduce the risk of electric shock, insure electricity
has been turned off at the circuit breaker or fuse box
before beginning.
2. All wiring must be in accordance with the National
Electrical Code ANSI/NFPA 70-1999 and local electrical
codes. Electrical installation should be performed by a
qualied licensed electrician.
3. WARNING: To reduce the risk of re or electric shock, do
not use this fan with any solid-state speed control device.
4. CAUTION: To reduce the risk of personal injury, use only
the screws provided with the outlet box.
5. The outlet box and support structure must be securely
mounted and capable of reliably supporting 35 lbs. (15.9
kg). Use only UL Listed outlet boxes marked “Acceptable
for Fan Support of 35 lbs. (15.9 kg) or less.”
6. The fan must be mounted with a minimum of 7 feet
clearance from the trailing edge of the blades to the oor.
7. Do not operate reversing switch while fan blades are in mo-
tion. Fan must be turned off and blades stopped before re-
versing blade direction.
8. Avoid placing objects in path of the blades.
9. To avoid personal injury or damage to the fan and other items,
be cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box, and the ungrounded
conductor on the other side of the outlet box.
12. Electrical diagrams are for reference only. Light kits that are
not packed with the fan must be UL listed and marked suitable
for use with the model fan you are installing. Switches must be
UL General Use Switches. Refer to the instructions packaged
with the light kits and switches for proper assembly.
13. SUITABLE FOR USE IN WET LOCATIONS when
installed in a GFCI protected branch circuit.
14. All set screws must be checked and retightened where
necessary before installation.
Safety Rules 1.
READ AND SAVE THESE INSTRUCTIONS
PLEASE REMOVE RUBBER MOTOR STOPS ON THE BOTTOM OF THE
FAN BEFORE INSTALLING BLADES OR TESTING THE MOTOR.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN
SUPPORT OF 35LBS (15.9 KG) OR LESS AND USE SCREWS PROVID-
ED WITH THE OUTLET BOX.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE BRACKETS WHEN INSTALLING THE BRACKETS, BALANCING
THE BLADES, OR CLEANING THE FAN.

a. Electrical & Mounting Hardware
(3 plastic wire connectors, 1 hanger pin, 1
locking pin)
b. Close-to-Ceiling mount hardware
(1 rubber gasket)
c. Blade attachment hardware
(16 screws)
d. Miscellaneous Parts
(1 pull chain)
7. Blades (5)
8. Blade Bracket (Flange) Set (5)
with blade bracket screws pre-installed
1. Slide-On Mounting Plate (inside canopy)
2. Ball/Downrod Assembly
3. Canopy with Canopy Ring attached
4. Fan Motor Assembly
5. Switch Cup
6. Decorative Motor Collar Cover
2. Unpacking Your Fan
IMPORTANT: THIS PRODUCTAND/OR COMPONENTSARE COVERED BY
ONEORMOREOFTHE FOLLOWING U.S. PATENTS:5,947,436; 5,988,580;
5,971,573; 6,010,110; 6,010,306; 6,039,541; 6,046,416 AND OTHER
PATENTS PENDING.
Unpack your fan and check the contents. You should have the following items:
8
6
5
4
3
2
17
c
ab
d

Installing Your Fan 3.
Tools Required
Phillips screw driver, straight slot screw
driver, adjustable wrench, step ladder, and
wire cutters.
Mounting Options
If there isn’t an existing outlet box, then read
the following instructions. Disconnect the
power by removing fuses or turning off
circuit breakers.
Secure the outlet box directly to the building struc-
ture. Use appropriate fasteners and build-
ing materials. The outlet box and its support
must be able to fully support the moving
weight of the fan (35 lbs. (15.9 kg) or less)
Do not use plastic outlet boxes.
Figures 1, 2, and 3 are examples of different
ways to mount the outlet box.
Outlet Box
Outlet Box
Recessed
Outlet Box
Ceiling
Mounting
Plate
Provide Strong
Support
Note: You may need a longer downrod to
maintain proper blade clearance when install-
ing on a steep, sloped ceiling. The maximum
angle allowable is 30˚. If the canopy touches
downrod, remove the decorative canopy
bottom cover and turn the canopy 180˚ before
attaching the canopy to the mounting plate.
Outlet Box
To hang your fan where there is an existing
xture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at your Hampton Bay retailer).
THE OUTLET BOX AND SUPPORT STRUCTURE
MUST BE SECURELY MOUNTED AND CAPABLE
OF RELIABLY SUPPORTING 35 LBS. (15.9 KG).
USE ONLY UL LISTED OUTLET BOXES MARKED
“ACCEPTABLE FOR FAN SUPPORT OF 35
LBS. (15.9 KG) OR LESS.” OUTLET BOXES
COMMONLY USED FOR THE SUPPORT
OF LIGHTING FIXTURES MAY NOT BE
ACCEPTABLE FOR FAN SUPPORT AND
MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Figure 1
Figure 2
Figure 4
Figure 3

each section of the instructions will note the
different procedures to follow for the two
types of installation.
Standard Ceiling Mounting
1. Remove the canopy ring from the canopy
by turning the ring to the right until it
unlocks (Figure 5).
2. Remove the mounting plate from the
canopy by loosening the four screws on
the top of the canopy. Remove the two
non-slotted screws and loosen the slotted
screws. This will enable you to remove the
mounting plate (Figure 6).
4.
Hanging the Fan
REMEMBER to turn off the pow-
er. Follow the steps below to hang your
fan properly.
NOTE: This ceiling fan is supplied with two
types of hanging assemblies; the standard
ceiling installation using the downrod with
ball and socket mounting, and the “close-to-
ceiling” mounting. The “close-to-ceiling”
mounting is recommended in rooms with
less than 8-foot ceilings or in areas where
additional space is desired from the oor
to the fan blades. When using standard
downrod installation, the distance from the
ceiling to the bottom of the fan blades will be
approximately 11 inches. The “close-to-ceiling”
installation reduces the distance from the
ceiling to the bottom of the fan blades to
approximately 7 inches.
Once you have decided which ceiling
installation you will use, proceed with the
following instructions. Where necessary,
Remove
Loosen but
Do Not Remove
Turn Canopy Ring to Remove
Figure 5
Figure 6 Figure 7
3. Route the wires exiting the top of the
fan motor through the decorative motor
collar cover then the canopy ring. Make sure
the slot openings are on top. Route the wires
through the canopy and then through the
ball/downrod assembly (Figure 7).
Downrod Cover Pin in
Locked
Position
Locking Pin
Hanger Pin
Motor Collar Cover
Canopy Ring
Canopy
Downrod/Ball
Assembly
Motor Wires
Hook
Ceiling
Mounting
Plate
Mounting Screws
(Supplied With
Outlet Box)
UL Listed
Outlet Box
Slide Mounting
Plate Over
Screw Heads
120V Wires
WHEN MOUNTING THE FAN ON A SLOPED
CEILING, THE STANDARD BALL/DOWNROD
MOUNTING METHOD MUST BE USED. THE
MOUNTING PLATE MUST BE MOUNTED SO
THAT THE SLOT OPENINGS ARE ON THE
LOWER SIDE BY SLIDING THE MOUNTING
PLATE FROM THE TOP DOWN. FOR A GREATER
MOUNTING ANGLE, REMOVE THE DECORA-
TIVE CANOPY BOTTOM COVER (FIGURE 9).

“Close-to-Ceiling” Mounting
1. Remove the canopy ring from the canopy
by turning the ring to the right until it
unlocks (Figure 5).
2. Remove the mounting plate from the cano-
py by loosening the four screws on the top
of the canopy. Remove the two non-slotted
screws and loosen the slotted screws. This
will enable you to remove the mounting
plate (Figure 6).
3. Remove the decorative canopy bottom cov-
er from the canopy by depressing the three
studs (Figure 9).
4. Remove three of the six screws and lock-
washers (every other one) securing the re-
inforcing plate to the top of the fan motor
housing (Figure 10).
5. Place the rubber gasket over the remaining
three screws, route the wires exiting the top
of the fan motor through the ceiling cano-
py over the collar at the top of the motor
(Figure 11).
5.
4. Loosen, but do not remove, the set
screw on the collar on the top of the
motor housing.
5. Align the holes at the bottom of the
downrod with the holes in the collar
on top of the motor housing (Figure 7).
Carefully insert the hanger pin through
the holes in the collar and downrod. Be
careful not to jam the hanger pin against
the wiring inside the downrod. Insert the
locking pin through the hole near the
end of the hanger pin until it snaps into its
locked position, as noted in the circle inset
of Figure 7.
6. Re-tighten the set screws on the collar on top
of the motor housing (Figure 8).
7. Proceed to “Installing the Fan” section.
FAILURE TO PROPERLY INSTALL SET SCREWS
IN STEP 7 COULD RESULT IN FAN LOOSENING
AND POSSIBLY FALLING.
FAILURE TO PROPERLY INSTALL THE LOCK-
ING PIN AS NOTED IN STEP 5 COULD RESULT
IN FAN LOOSENING AND POSSIBLY FALLING.
Figure 8
Tighten
Set
Screws
Figure 9
Canopy
Bottom
Cover
Figure 10
Figure 11
Motor Collar
Screw and
Lockwasher
(3 of 6 Screws)
Collar
Screw and
Lockwasher
(3 Screws)
Ceiling
Canopy
Canopy
Ring
Rubber
Gasket
6. Align the mounting holes with the holes
in the motor and fasten, using the three
screws and lock-washers removed in step 4
(Figure 11).
7. Tighten the mounting screws securely.

6.
WHEN USING THE STANDARD BALL/DOWN-
ROD MOUNTING, THE TAB IN THE RING AT THE
BOTTOM OF THE MOUNTING BRACKET MUST
REST IN THE GROOVE OF THE HANGER BALL.
FAILURE TO PROPERLY SEAT THE TAB IN THE
GROOVE COULD CAUSE DAMAGE TO WIRING.
Installing Fan to
the Outlet Box
WHEN MOUNTING THE FAN ON A SLOPED
CEILING, THE STANDARD BALL/DOWNROD
MOUNTING METHOD MUST BE USED. MAKE
SURE THE MOUNTING BRACKET SLOTS ARE
ON THE LOWER SIDE BY SLIDING THE MOUNT-
ING BRACKET FROM THE TOP DOWN.
1. Pass the 120-volt supply wires through the
center hole in the ceiling mounting bracket
as shown in Figure 7.
2. Install the ceiling mounting plate on the out-
let box by sliding the mounting bracket over
the two screws provided with the outlet box.
When using close-to-ceiling mounting, it is
important that the mounting plate be level.
If necessary, use leveling washers (not in-
cluded) between the mounting bracket and
the outlet box. Note that the at side of the
mounting bracket is toward the outlet box
(Figure 7).
3. Securely tighten the two mounting screws.
4. Carefully lift the assembly up to the ceil-
ing mounting plate. If using Close-to-
Ceiling mounting, hang the fan on the
hook provided by utilizing one of the
holes at the outer rim of the ceiling canopy
(Figure 12). If using standard mounting, seat
the hanger ball in the mounting plate socket.
Make sure the tab on the mounting bracket
socket is properly seated in the groove in the
hanger ball (Figure 12).
Close-to-Ceiling
Mounting
Standard
Mounting
Figure 12
THE HOOK AS SHOWN IN FIGURE 12 IS ONLY
TO BALANCE FAN WHILE ATTACHING WIRING.
FAILURE TO HANG AS SHOWN IN FIGURE 12
MAY RESULT IN HOOK BREAKING, CAUSING
THE FAN TO FALL. HOOK MUST PASS FROM
INSIDE TO OUTSIDE OF CANOPY.
Making the Electrical
Connections
REMEMBER to disconnect the power. If
you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Follow the steps below to connect the fan
to your household wiring. Use the wire
connecting nuts supplied with your fan. Se-
cure the connectors with electrical tape.
Make sure there are no loose strands or
connections.
1. Connect the two green fan ground wires lo-
cated on the downrod and mounting plate
to the household ground wire. When using
Close-to-Ceiling mounting, there is only one
green ground wire from the ceiling mount-
ing plate since the ball/downrod assembly is
not used.
2. IF USING OPTIONAL LIGHT KIT, Con-
nect the fan light supply (blue) wire and the
fan supply (black) wire to the black house-
hold supply wire as shown in gure 13.
3. Connect the neutral fan (white) wire to the
white neutral household wire.
4. After connecting the wires, spread them
apart so that the green and white wires are
on side of the outlet box and the black wire
is on the other side.
ELECTRICAL DIAGRAMS ARE FOR REFERENCE
ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL
BE UL LISTED AND MARKED SUITABLE FOR
USE WITH THIS FAN.
USE ONLY WITH LIGHT KITS MARKED “SUIT-
ABLE FOR USE IN WET LOCATION”.

7.
EACH WIRE NUT (WIRE CONNECTOR) SUP-
PLIED WITH THIS FAN IS DESIGNED TO ACCEPT
UP TO ONE 12 GAUGE HOUSE WIRE AND TWO
WIRES FROM THE FAN. IF YOU HAVE LARGER
THAN 12 GAUGE HOUSE WIRING OR MORE
THAN ONE HOUSE WIRE TO CONNECT TO THE
FAN WIRING, CONSULT AN ELECTRICIAN FOR
THE PROPER SIZE WIRE NUTS TO USE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT USE A WALL MOUNTED SOLID
STATE SPEED CONTROL WITH THIS FAN. IT
WILL PERMANENTLY DAMAGE THE ELEC-
TRONIC CIRCUITRY.
Figure 13
BLUE BLACK
WHITE
GREEN
BLUE
BLACK WHITE
WHITE
Outlet
Box
SUPPLY CIRCUIT
Green
Grounding
Lead
WHITE
Ground
to
Downrod
BLACK
Switch
5. Turn the wire connecting nuts upward and
push the wiring into the outlet box. Finishing the Fan
Installation
STANDARD CEILING MOUNTING
1. Align the locking slots of the ceiling canopy
with the two screws in the mounting bracket.
Push up to engage the slots and turn clock-
wise to lock in place. Immediately tighten
the two mounting screws rmly.
2. Install the remaining two mounting
screws into the holes in the canopy and
tighten rmly.
3. Install the decorative canopy ring by align-
ing the ring’s slots with the screws in the
canopy. Rotate the ring clockwise to lock in
place.
4. You may now proceed to attaching the
fan blades.
WHEN USING THE STANDARD BALL/DOWNROD
MOUNTING, THE TAB IN THE RING AT THE BOT-
TOM OF THE MOUNTING PLATE MUST REST IN
THE GROOVE OF THE HANGER BALL. FAILURE
TO PROPERLY SEAT THE TAB IN THE GROOVE
COULD CAUSE DAMAGE TO WIRING.
Diagram indicates optional light kit

CLOSE-TO-CEILING MOUNTING
1. Carefully unhook the fan from the mount-
ing bracket and align the locking slots of
the ceiling canopy with the two screws in
the mounting plate. Push up to engage the
slots and turn clockwise to lock in place. Im-
mediately tighten the two mounting screws
rmly.
2. Install the remaining two mounting screws
into the holes in the canopy and tighten
rmly.
3. Install the decorative canopy ring by align-
ing the ring’s slots with the screws in the
canopy. Rotate the ring clockwise to lock in
place.
4. You may now proceed to attaching the fan
blades.
8.
LOCKING SLOTS OF CEILING CANOPY ARE
PROVIDED ONLY AS AN AID TO MOUNTING.
DO NOT LEAVE FAN ASSEMBLY UNATTENDED
UNTIL ALL FOUR CANOPY SCREWS ARE EN-
GAGED AND FIRMLY TIGHTENED.
Attaching the
Fan Blades
1. Attach blade to blade bracket using the
screws as shown in gure 14. Please note that
the rubber washers are pre-attached to the
blade bracket. Start a screw into the bracket.
Repeat for the two remaining screws
2. Tighten each screw securely.
Alignment Post
Blade Bracket
Screw
Slot
Screws
Pre-Installed
Screws
Blade
Blade
Bracket
Rubber
Washers
Figure 14
Figure 15
REMOVE RUBBER STOPPERS ON THE BLACK
PLATE BELOW THE MOTOR TO ATTACH BLADE
ASSEMBLY TO MOTOR. REPLACE RUBBER
STOPPERS TO PREVENT WATER FROM ENTER-
ING SWITCH HOUSING AND TO REDUCE RISK
OF FIRE, ELECTRIC SHOCK OR OTHER PER-
SONAL INJURY.
3. Fasten the blade assembly to the motor by
inserting the alignment post into the slot on
the bottom of the motor and tightening the
blade bracket screws. Please note that the
blade bracket screws are pre-installed into
the blade bracket (Figure 15).
4. Repeat steps 1-3 for the remaining blades.
Attaching the
Switch Housing
1. Connect the adaptor plug exiting the bottom
of the motor with the plug from the switch
housing.
2. Mount the switch housing to the black plate
below the motor by aligning the four screw
holes and securing with the four tapered
screws provided.

Operating Your Fan 9.
Figure 16
Figure 17
Figure 18
Blade Balancing
All blades are grouped by weight. Because nat-
ural woods vary in density, the fan may wobble
even though the blades are weight matched. The
following procedure should correct most fan
wobble. Check after each step.
1. Check that all blade and blade bracket
screws are secure.
2. Most fan wobble problems are caused when
blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip
of one of the blades. Measure from a point
on the center of each blade to the point on the
ceiling. Measure this distance as shown in
Figure 16. Rotate the fan until the next blade
is positioned for measurement. Repeat for
each blade. Measurement deviations should
within 1/8”. Run the fan for 10 minutes.
3. If the fan continues to wobble please contact
Customer Service and a balacing kit will be
sent to you at no charge.
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE HOLDERS WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NOT INSERT FOREIGN
OBJECTS BETWEEN ROTATING BLADES.
Operating your Fan
Turn on the power and check the operation of
the fan. The pull chain controls the fan speeds
as follows: 1 pull - High, 2 pulls - Medium, 3
pulls - Low and 4 pulls - Off
Speed settings for warm or cool weather depend
on factors such as room size, ceiling height,
number of fans, and so on.
The slide switch controls the direction: forward
(switch left) or reverse (switch right).
Warm weather - (Forward) A downward
air ow creates a cooling effect as shown in
Figure 17. This allows you to set your air condi-
tioner on a higher setting without affecting your
comfort.
WAIT FOR FAN TO STOP BEFORE REVERSING
THE DIRECTION OF BLADE ROTATION.
Cool weather - (Reverse) An upward air ow
moves warm air off the ceiling are as shown in
Figure 18. This allows you to set your heating
unit on a lower setting without affecting your
comfort.

10. Care of Your Fan and Troubleshooting
Care of Your Fan
Here are some suggestions to help you
maintain your fan.
1. Because of the fan’s natural movement,
some connections may become loose.
Check the support connections, brackets,
and blade attachments twice a year. Make
sure they are secure. (It is not necessary to
remove fan from ceiling.)
2. Clean your fan periodically to help maintain
its new appearance over the years. Do not
use water when cleaning, this could damage
the motor, or the wood or possibly cause
an electrical shock. Use only a soft brush
or lint-free cloth to avoid scratching the
nish. The plating is sealed with a lacquer
to minimize discoloration or tarnishing.
Warning - Make sure the power is off
before cleaning your fan.
3. You can apply a light coat of furniture pol-
ish to the wood for additional protection
and enhanced beauty. Cover small scratches
with a light application of shoe polish.
4. There is no need to oil your fan.
The motor has permanently lubricated
sealed ball bearings. MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BE-
FORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION,
“MAKING ELECTRICAL CONNECTIONS.”
Fan will not start
Fan sounds noisy
1. Check main and branch circuit fuses or breakers
2. Check line wire connections to the fan and switch wire connections in
the switch housing. CAUTION: Make sure main power is off.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub
are tight.
3. Make sure wire nut connections are not rattling against each other or
the interior wall of the switch housing.
CAUTION: Make sure power is off.
4. Allow a 24-hour “breaking in” period. Most noises associated with a
new fan disappear during this time.
5. If using the Ceiling Fan light kit, make sure the screws securing the
glassware are tight. Check that the light bulb is also secure.
6. Make sure the canopy is a short distance from the ceiling.
It should not touch the ceiling.
7. Make sure your outlet box is secure and rubber isolator pads were used
between the mounting plate and outlet box.
Troubleshooting
Problem Solution

Specications 11.
FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM NET
WEIGHT
GROSS
WEIGHT CUBE FEET
48”
Low 120 0.25 13.2 77 2257
21.3
Lbs
23.5
Lbs 1.43’Med 120 0.38 30.6 126 3466
High 120 0.55 66.6 187 5034
These are approximate measures. They do not include Amps and Wattage used by the light kit.
Distributed by
Your Other Warehouse LLC
12100 Little Cayman Dr.
Baton Rouge, LA 70809
Vendor number: 219030

12. Warranty Information
Hampton Bay Lifetime Limited Warranty
Lifetime Warranty on Motor
Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at
time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free
from defects in workmanship and material at the time of shipment from the factory for a period of
one year after the date of purchase by the original purchaser. We agree to correct such defects without
charge or at our option replace with a comparable or superior model if the product is returned to
Hampton Bay. To obtain warranty service, you must present a copy of the receipt as proof of purchase.
All costs of removing and reinstalling the product are your responsibility. Damage to any part such
as by accident or misuse or improper installation or by afxing any accessories, is not covered by
this warranty. Because of varying climatic conditions, this warranty does not cover any changes in
plated nishes, including rusting, pitting, corroding, tarnishing or peeling. Brass nishes of this type
give their longest useful life when protected from varying weather conditions. A certain amount of
“wobble” is normal and should not be considered a defect. Servicing performed by unauthorized
persons shall render the warranty invalid. There is no other express warranty. Hampton Bay hereby
disclaims any and all warranties, including but not limited to, those of merchantability and tness
for a particular purpose to the extent permitted by law. The duration of any implied warranty which
cannot be disclaimed is limited to the time period as specied in the express warranty. Some states
do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply
to you. Hampton Bay shall not be liable for incidental, consequential, or special damages arising
out of or in connection with product use or performance except as may otherwise be accorded by
law. Some states do not allow the exclusion of incidental or consequential damages, so the above
exclusion or limitation may not apply to you. This warranty gives specic legal rights, and you may
also have other rights which vary from state to state. This warranty supersedes all prior warranties.
Shipping costs for any return of product as part of a claim on the warranty must be paid by the
customer.
IMPORTANT NOTE:
To ensure warranty service, if ever
necessary, please register your fan at:
gpwarranty.com
You must present a copy of the original
purchase receipt to obtain warranty service.
G.P. WARRANTY SERVICE CENTER, INC.
WARRANTY SECTION
1951 N.W. 22nd STREET
FORT LAUDERDALE, FLORIDA 33311
Attach receipt here for
easy location.

Largo de 48"
Ventilador de techo de Hampton Bay
Accu-arm™ para una instalación fácil
y precisa
Para uso en interiores y exteriores
Función de reversa de 3 velocidades para
confort y ahorro durante todo el año
Instalación de montaje triple
¿PREGUNTAS, PROBLEMAS O PIEZAS FALTANTES?
Antes de volver a tu tienda local de The Home Depot, llama a nuestro
Equipo de Servicio al Cliente al 1-877-527-0313 o visita www.homedepot.com.
Por favor usa como referencia el Nº de SKU (705 544 hierro dorado, 635 289 blanco mate, 998 418 cinc envejecido)
o UPC (082392 266844 hierro dorado, 082392 266820 blanco mate, 082392 266851 cinc envejecido).
Gracias por comprar este ventilador de techo de
Hampton Bay. Este producto se ha fabricado con las
normas de seguridad y calidad más altas. El acabado
de este ventilador es resistente a la intemperie, pero
con el tiempo, exhibirá un desgaste y decoloración
naturales.
Normas de seguridad................... 1
Cómo desempacar el ventilador . 2
Cómo instalar el ventilador......... 3
Cómo operar el ventilador .......... 9
Cuidado del ventilador ................ 10
Solución de problemas................. 10
Especicaciones............................ 11
Información de la garantía.......... 12
Índice
Modelo de UL Nº 48-LG

1. Para disminuir el riesgo de descarga eléctrica, asegúrate de
que la electricidad ha sido apagada en el cortacircuitos o
la caja de fusibles antes de comenzar la instalación.
2. Todo el cableadodebe cumplir con el CódigoNacional de Electricidad
ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La
instalación eléctrica debe ser hecha por un electricista certicado y
calicado.
3. ADVERTENCIA: Para reducir el riesgo de incendio o descarga
eléctrica, no utilices este ventilador con ningún dispositivo de control
de velocidad de estado sólido.
4. PRECAUCIÓN: Para reducir el riesgo de lesiones físicas, usa sólo
los tornillos provistos con la caja eléctrica.
5. La caja eléctrica y estructura de soporte deben montarse de forma
segura y tener capacidad para sostener de manera conable 35 lb.
Usa solamente cajas eléctricas aprobadas por UL marcadas como
“Aprobada como soporte de ventiladores de 35 lb (15,9 kg) o menos.”
6. El ventilador debe ir montado con un mínimo de 7 pies de separación
entre el borde trasero de las aspas y el piso.
7. No operar el interruptor de reversa mientras las aspas del ventilador
estén en movimiento. El ventilador debe estar apagado y las aspas
detenidas antes de invertir la dirección del movimiento.
8. Evita colocar objetos en la trayectoria de las aspas.
9. Para evitar lesiones, o daños al ventilador y otros objetos; ten cuidado
al trabajar cerca del ventilador o al limpiarlo.
10. No usar agua o detergentes para limpiar el ventilador o las aspas.
En general a la hora de limpiar, bastará con usar un paño seco o
ligeramente humedecido.
11. Después de concluir con las conexiones eléctricas, debes voltear
los conductores empalmados hacia arriba y empujarlos con cuidado
hacia dentro de la caja eléctrica. Los cables deben estar separados,
con el cable a tierra y el conductor a tierra del equipo hacia uno de
los lados de la caja eléctrica y el conductor sin conexión a tierra hacia
el lado opuesto.
12. Los diagramas eléctricos son sólo una referencia. Los kits de luces
no empaquetados con el ventilador deben estar aprobados por UL
y marcados como apropiados para ser usados con el modelo de
ventilador a instalar. Los interruptores deberán estar clasicados por
el UL como de Uso General. Consulta las instrucciones adjuntas a
los kits de luces e interruptores para obtener información sobre el
ensamblado adecuado.
13. ADECUADO PARA USO EN LUGARES HÚMEDOS si
se instala en un circuito derivado protegido por un interruptor
diferencial (GFCI, en inglés).
14. Todos los tornillos colocados se deben vericar y ajustar donde sea
necesario antes de la instalación.
1. Normas de seguridad
LEE LAS INSTRUCCIONES Y GUÁRDALAS
PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES
PERSONALES, MONTA EL VENTILADOR SOBRE UNA CAJA ELÉCTRICA
MARCADA COMO APROBADA COMO SOPORTE DE VENTILADORES DE 35 LB
(15,9 KG) O MENOS, Y USA LOS TORNILLOS DE MONTAJE QUE VIENEN CON
LA MISMA.
PARA REDUCIR EL RIESGO DE LESIONES PERSONALES, NO DOBLAR LOS
SOPORTES DE LAS ASPAS DURANTE LA INSTALACIÓN DE LOS SOPORTES,
COMPENSACIÓN DE LAS ASPAS O LIMPIEZA DEL VENTILADOR.
RETIRA LOS TOPES DE GOMA DEL MOTOR EN LA PARTE INFERIOR DEL
VENTILADOR ANTES DE INSTALAR LAS ASPAS O PROBAR EL MOTOR.

a. Herrajes de montaje y electricidad
(3 conectores plásticos de cable, 1 pasador
de soporte, 1 pasador de cierre)
b. Herrajes para montaje
“Cerca del Techo” (1 junta de goma)
c. Herrajes de montaje de aspas
(16 tornillos)
d. Piezas varias
(1 cadena para halar)
6. Cubierta decorativa del collarín del motor
7. Aspas (5)
8. Juego de soportes (reborde) de aspa (5)
con tornillos de soporte de aspa
preinstalados
1. Placa de montaje deslizante
(dentro de la cubierta)
2. Ensamblado de tubo bajante/bola
3. Cubierta con anillo de cubierta acoplado
4. Ensamblado del motor del ventilador
5. Caja del interruptor
Cómo desempacar el ventilador 2.
IMPORTANTE: ESTE PRODUCTO Y/O SUS COMPONENTES
ESTÁN PROTEGIDOS POR UNA O MÁS DE LAS SIGUIENTES
PATENTES DE EE.UU.: 5,947,436; 5,988,580; 5,971,573;
6,010,110; 6,010,306; 6,039,541; 6,046,416 y OTRAS
PATENTES PENDIENTES.
Desempaca tu ventilador y revisa el contenido. Deberá tener las siguientes piezas:
8
6
5
4
3
2
17
c
ab
d

3. Cómo instalar el ventilador
Herramientas
necesarias
Destornillador Phillips, destornillador plano,
llave ajustable, escalera de tijera y cortacables.
Opciones de montaje
Si no hay una caja eléctrica existente, entonces lee
las siguientes instrucciones. Desconecta la energía
retirando los fusibles o apagando los cortacircuitos.
Asegura la caja eléctrica directamente a la
estructura del edicio. Usa sujetadores y materiales
de construcción apropiados. La caja eléctrica y
estructura de soporte deben montarse de forma segura
y tener capacidad para sostener de manera conable
35 lb. Usa solamente cajas eléctricas aprobadas por
UL marcadas como “Aprobada como soporte de
ventiladores de 35 lb (15,9 kg) o menos.”
Las guras 1, 2 y 3 son ejemplos de diferentes
formas de montar la caja eléctrica.
Caja
eléctrica
Caja eléctrica
Caja eléctrica
empotrada
Placa de
montaje
en el techo
Soporte
fuerte
Nota: Tal vez necesites un tubo bajante más
largo para mantener la altura mínima adecuada
de las aspas al instalar el ventilador en un techo
inclinado. El ángulo máximo permitido es
de 30º. Si la cubierta toca el tubo bajante,
retira la cubierta inferior decorativa y gira
la cubierta 180º antes de jar la cubierta a la
placa de montaje.
Caja eléctrica
Paracolgar tu ventilador donde haya una lámpara
pero ninguna viga de techo, tal vez necesites
una barra colgante de instalación como se
muestra en la Figura 4 (disponible en la tienda
minorista local de Hampton Bay).
PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA
ELÉCTRICA O LESIONES PERSONALES, MONTA EL
VENTILADOR SOBRE UNA CAJA ELÉCTRICA MARCADA
COMO“APROBADA COMO SOPORTE DEVENTILADORES
DE 35 LB (15,9 KG) O MENOS”, Y USA LOS TORNILLOS
DE MONTAJE QUE VIENEN CON LA MISMA. LAS CAJAS
ELÉCTRICAS UTILIZADAS COMÚNMENTE PARA EL
SOPORTE DE ARTÍCULOS DE ILUMINACIÓN PUEDEN
NO SERVIR COMO SOPORTE DE VENTILADOR, Y TAL
VEZ DEBAN REEMPLAZARSE. EN CASO DE DUDA,
CONSULTA A UN ELECTRICISTA CALIFICADO.
Figura 1
Figura 2
Figura 4
Figura 3

con las siguientes instrucciones. Cuando sea
necesario, cada sección de las instrucciones
indicará los diferentes procedimientos a seguir
para los dos tipos de instalación.
Montaje de techo estándar
1. Retira el aro en la cubierta, girando a la
derecha hasta destrabarlo (Figura 5).
2. Retira la placa de montaje de la cubierta
aojando los cuatro tornillos de la parte
superior de la misma. Quita los dos tornillos
sin ranura y aoja los tornillos ranurados.
Esto te permitirá retirar la placa de montaje
(Figura 6).
4.
Cómo colgar el
ventilador
RECUERDA desconectar la corriente.
Sigue estos pasos para colgar correctamente tu
ventilador.
NOTA: Este ventilador de techo viene con dos
tipos de ensamblados de soporte; la instalación
de techo estándar con tubo bajante y bola,
y casquillo de montaje; y el montaje “cerca
del techo”. El montaje “cerca del techo” se
recomienda en habitaciones con techos de
menos de 8 pies de altura o en áreas donde
se desee espacio adicional desde el piso hasta
las aspas de ventilador. Cuando uses una
instalación con un tubo bajante estándar, la
distancia desde el techo a la parte inferior de las
aspas será de 11 pulgadas aproximadamente. La
instalación “cerca del techo” reduce la distancia
desde el techo a la parte inferior de las aspas a 7
pulgadas aproximadamente.
Una vez elegido el tipo de instalación, sigue
Quitar
Aflójalo pero
no lo quites
Gira el aro en la cubierta para quitarla
Figura 5
Figura 6 Figura 7
3. Inserta los cables que salen por la parte
superior del motor del ventilador, primero, a
través de la cubierta decorativa del collarín
del motor y luego, por el aro de la cubierta.
Asegúrate de que las aberturas en forma de
ranura estén en la parte superior. Inserta los
cables a través de la cubierta y luego a través
del ensamblado del tubo bajante y la bola
(Figura 7).
Cubierta del
tubo bajante
Posición
de cierre
del
pasador
Tornillos
de montaje
(provistos con
la caja eléctrica)
Gancho
Placa de
montaje
de techo
Cable de 120 V
Desliza
la placa
de montaje
sobre la cabeza
de los tornillos
Caja
eléctrica
aprobada
por UL
Cables del motor
Ensamblado
de tubo
bajante/bola
Pasador
de cierre
Cubierta
Aro de la
cubierta
Pasador
de soporte
Cubierta del
collarín del motor
CUANDO MONTES ELVENTILADOR EN UNTECHO
INCLINADO, DEBES USAR EL MÉTODO
DE MONTAJE CON TUBO BAJANTE
Y BOLA ESTÁNDAR. LA PLACA DE
MONTAJE DEBE ESTAR INSTALADA DE
MANERA TAL QUE LAS ABERTURAS
EN FORMA DE RANURA QUEDEN EN EL LADO
INFERIOR, DESLIZANDO LA PLACA DE MONTAJE
DESDE LA PARTE SUPERIOR HACIA ABAJO. SI
EL ÁNGULO DE MONTAJE ES MAYOR, RETIRA
LA CUBIERTA INFERIOR DECORATIVA DE LA
CUBIERTA (FIGURA 9).

4. Aoja, sin quitarlo, el tornillo en el collarín
ubicado en la parte superior de la carcasa del
motor.
5. Alinea los oricios en la parte inferior del
tubo bajante con los oricios en el collarín
ubicado en la parte superior de la carcasa
de motor (Figura 7). Inserta con cuidado el
pasador de soporte a través de los oricios
del collarín y del tubo bajante. Ten cuidado
de no apretarlo contra el cableado dentro del
tubo bajante. Inserta el pasador de cierre en
el oricio cercano al extremo del pasador
de soporte hasta que quede encajado en su
posición como se muestra en el círculo de
la Figura 7.
6. Vuelve a ajustar los tornillos del collarín
en la parte superior de la carcasa del motor
(Figura 8).
7. Sigue con la sección "Cómo instalar el
ventilador"
Montaje “Cerca del Techo”
1. Retira el aro en la cubierta, girando a la
derecha hasta destrabarlo (Figura 5).
2. Retira la placa de montaje de la cubierta
aojando los cuatro tornillos de la parte
superior de la misma. Quita los dos tornillos
sin ranura y aoja los tornillos ranurados.
Esto te permitirá retirar la placa de montaje
(Figura 6).
3. Retira la cubierta inferior decorativa de
la cubierta oprimiendo los tres pernos
(Figura 9).
4. Retira tres de los seis tornillos y arandelas
de seguridad (alternados) que sujetan la
placa de refuerzo a la parte superior de la
carcasa del motor (Figura 10).
5. Coloca la junta de goma sobre los otros tres
tornillos, inserta los cables que salen por
la parte superior del motor del ventilador
a través de la cubierta sobre el collarín
ubicado en la parte superior del motor
(Figura 11).
5.
SI NO COLOCAS CORRECTAMENTE LOS TORNILLOS
SEGÚN LO INDICADO EN EL PASO 7 SE PUEDEN
AFLOJAR Y POSIBLEMENTE SE CAIGA EL
VENTILADOR.
Figura 8
Aprieta
los
tornillos
Figura 9
Cubierta
inferior Figura 10
Figura 11
Collarín
del motor
Tornillo y
arandela
de seguridad
(3 de 6 tornillos)
Collarín
Tornillo y
arandela de
seguridad (3
tornillos)
Cubierta
de techo Aro de la
cubierta
Junta
de goma
6. Alinea los oricios de montaje con los
oricios del motor y asegura con los tres
tornillos y arandelas de seguridad retiradas
en el paso 4 (Figura 11).
7. Asegúrate de ajustar bien los tornillos de
montaje.
SI NO INSTALAS CORRECTAMENTE EL PASADOR
DE CIERRE SEGÚN LO INDICADO EN EL PASO 5 SE
PUEDE AFLOJAR Y POSIBLEMENTE SE CAIGA EL
VENTILADOR.