HAMPTON BAY PALMARIA EF200S(X)-52 User manual

USE AND CARE GUIDE
PALMARIA 52-INCH CEILING FAN
Item #1008 655 076
Model #92408
UL Model #EF200S(X)-52
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
THANK YOU
We appreciate the trust and condence you have placed in Hampton Bay through the purchase of this ceiling fan. We strive to continually create
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!

2
Table of Contents ................................................................2
Safety Information...............................................................2
Warranty ............................................................................... 3
Pre-Installation ....................................................................3
Installation............................................................................6
Assembly..............................................................................7
Operation ...........................................................................12
Care and Cleaning.............................................................13
Troubleshooting.................................................................13
1. All wiring must be in accordance with the National Electrical Code
ANSI/NFPA 70 and local electrical codes. Electrical installation
should be performed by a qualied licensed electrician.
2. The outlet box and support structure must be securely mounted
and capable of reliably supporting 35 pounds (15.9 kg). Use only
UL Listed outlet boxes marked “Acceptable for Fan Support of 35
pounds (15.9 kg) or less.”
3. The fan must be mounted with a minimum of 7 ft (2.1 m) clearance
from the trailing edge of the blades to the oor.
4. Do not operate the reversing switch while the fan blades are in
motion. You must turn the fan off and stop the blades before you
reverse the blade direction.
5. Do not place objects in the path of the blades.
6. Electrical diagrams are for reference only. Light kits that are not
packed with the fan must be UL listed and marked suitable for use
with the model fan you are installing. Switches must be UL General
Use Switches. Refer to the instructions packaged with the light kits
and switches for proper assembly.
7. After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into the outlet box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and
the ungrounded conductor on the other side of the outlet box..
8. All setscrews must be checked and retightened where necessary
before installation.
9. Suitable for use in wet locations when installed in a GFCI protected
branch circuit. Use only with light kits marked “Suitable for use in
wet locations”
WARNING: To reduce the risk of personal injury, do
not bend the blade brackets (also referred to as
anges) during assembly or after installation. Do not
insert objects in the path of the blades.
WARNING: To reduce the risk of re or electric shock,
do not use this fan with any solid-state speed control
device.
WARNING: Remove the rubber motor stops on the
bottom of the fan before installing the blades or
testing the motor.
WARNING: To avoid possible electrical shock, turn
the electricity off at the main fuse box before
wiring. If you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
Safety Information
Table of Contents
CAUTION: To reduce the risk of personal injury,
use only the screws provided with the outlet box.
CAUTION: To avoid personal injury or damage to the fan
and other items, use caution when working around or
cleaning the fan.
WARNING: To reduce the risk of re, electric shock
or personal injury, mount to outlet box marked
“acceptable for fan support of 35 lbs. (15.9 kg) or
less” and use screws provided with the outlet box.
READ AND SAVE THESE INSTRUCTIONS.
WARNING: To reduce the risk of re, electric shock or
injury to persons, do not use replacement parts that
have not been recommended by the manufacturer
(e.g. parts made at home using a 3D printer).
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party - U.S. Contact Information: King of Fans, Inc 1951 NW 22nd Street, Fort Lauderdale, FL 33311, [phone]

3HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Pre-Installation
Warranty
SPECIFICATIONS
TOOLS REQUIRED
NOTE: These are approximate measures. They do not
include the Amps and Wattage used by the light kit.
Phillips
screwdriver
Flat blade
screwdriver
Adjustable
wrench
Electrical
tape
Wire
cutter
Step ladder
Size Speed Volts Amps Watts RPM CFM Net
Weight
Gross
Weight Cubic Feet
52 in.
Low
Medium
High
120
0.23
0.33
0.51
11.86
24.42
61.48
68
98
156
2098
3071
4962
18.97 lbs
(8.6 kg)
25.13 lbs
(11.40 kg) 1.996 cu. ft.
The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a
lifetime after the date of purchase by the original purchaser. The supplier warrants that the light kit, excluding any glass, to be free from defects in
workmanship and material at the time of shipment from the factory for a period of three years after the date of purchase by the original purchaser.
The supplier also warrants that other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the
time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. We agree to correct such defects
without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service, you must present
a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part, such as by
accident, misuse, improper installation, or by afxing any accessories, is not covered by this warranty. Because of varying climatic conditions this
warranty does not cover any changes in brass nish, including rusting, pitting, corroding, tarnishing, or peeling. Brass nishes of this type give their
longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect.
Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay hereby disclaims
any and all warranties, including but not limited to those of merchantability and tness for a particular purpose to the extent permitted by law. The
duration of any implied warranty, which cannot be disclaimed, is limited to the time period as specied in the express warranty. Some states do not
allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental,
consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law.
Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This
warranty gives specic legal rights, and you may also have other rights that vary from state to state. This warranty supersedes all prior warranties.
Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HamptonBay.com.

4
Part Description Quantity
AA Rubber gasket 1
BB Pull chain 2
CC Hanger pin 1
DD Locking pin 1
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
EE Plastic wire connector 3
FF Rubber plug 1
GG Plastic plug 1
BBAA
EE
DD
CC
FF GG

5HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Part Description Quantity
ASlide-on mounting bracket
(inside canopy) 1
B Ball/downrod assembly 1
C Canopy 1
D Canopy ring (pre-assembled with canopy (C)) 1
E Coupler cover 1
Part Description Quantity
F Fan-motor assembly 1
GLight kit tter assembly 1
H Blade 5
I Blade bracket 5
J LED bulb 2
IMPORTANT: This product and/or components are
governed by one or more of the following U.S. Patents:
5,947,436; 5,988,580; 6,010,110; 6,046,416; 6,210,117
and other patents pending.
Pre-Installation (continued)
PACKAGE CONTENTS
A
B
C
D
E
F
G
H
I
J

6
Installation
MOUNTING OPTIONS
WARNING: To reduce the risk of re, electric shock
or personal injury, mount to outlet box marked
“Acceptable for fan support of 35 lbs. (15.9 Kg) or
less”, and use screws provided with the outlet box. An
outlet box commonly used for the support of lighting
xtures may not be acceptable for fan support and may
need to be replaced. If in doubt, consult a qualied
electrician.
If your ceiling fan does not have an existing UL-listed mounting
box, then install one using the following instructions:
□Disconnect the power by removing the fuses or turning off
the circuit breakers.
□Secure the outlet box directly to the building structure. Use
the appropriate fasteners and materials. The outlet box and
its bracing must be able to fully support the weight of the
moving fan (at least 35 lbs.). Do not use a plastic outlet box.
The illustrations below show three different ways to mount the
outlet box.
If the canopy touches the downrod, then remove the canopy bottom
cover, and turn the canopy 180° before attaching the canopy to the
mounting plate.
To hang your fan where there is an existing xture but no ceiling joist,
you may need an installation hanger bar as shown above
(available at any Home Depot store).
NOTE: You may need a longer downrod to maintain
proper blade clearance when installing on a steep, sloped
ceiling. The maximum angle allowable is 30° away from
horizontal.
Outlet Box
Outlet Box
Recessed
Outlet
Box
Provide Strong
Support
Ceiling
Mounting
Plate
Outlet Box
Hanger Bar

7HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly - Standard Ceiling Mount
Routing the wires
Assembling the fan
Preparing for mounting
□Remove the canopy ring (D) from the canopy (C) by
turning the ring counter-clockwise until it unlocks.
□Loosen, but do not remove, the two canopy screws (LL)
located in the “L shaped” slots.
□Remove and save the two canopy screws (HH) in the
round holes. This will enable you to remove the mounting
bracket (A).
□Route the wires exiting the top of the fan motor (F), through
the coupler cover (E) and canopy ring (D).
□Make sure the slot openings are on top and route the wires
through the canopy (C) and then through the ball downrod
assembly (B).
2
3
1
□Loosen, but do not remove, the set screws (RR) on the
collar on top of the motor housing (F).
□Align the holes at the bottom of the downrod (B) with the
holes in the collar on top of the motor housing (F).
□Carefully insert the hanger pin (CC) through the holes
in the collar and downrod (B). Be careful not to jam the
hanger pin (CC) against the wiring inside the downrod (B).
□Insert the locking pin (DD) through the hole near the end of
the hanger pin (CC) until it snaps into its locked position.
□Re-tighten the two set screws (RR) on the collar on top of
the motor housing.
WARNING: Failure to properly install the locking pin could
result in the fan becoming loose and possibly falling.
C
D
E
F
B
C
D
E
F
B
DD
RR
CC
A
C
D
HH
L
L

8
Assembly - Close to Ceiling Mount
Routing the wiresPreparing for mounting
□Remove the canopy ring (D) from the canopy (C) by turning the
ring counter-clockwise until it unlocks.
□Loosen, but do not remove, the two canopy screws (LL) located
in the “L shaped” slots.
□Remove and save the two canopy screws (HH) in the round
holes. This will enable you to remove the mounting bracket (A).
□Remove the canopy bottom cover (N) from the canopy (C) by
depressing the three studs.
□Remove three of the six screws and lock washers (every
other one) securing the motor collar to the top of the fan
motor (F).
□Place the rubber gasket (AA) over the remaining three
screws. Make sure the slot opening is on top, then proceed
to place the ceiling canopy (C) over the collar at the top of the
motor (F).
□Align the mounting holes with the holes in the motor (F) and
fasten, using the three screws and lock-washers removed
previously. Tighten the mounting screws securely.
21
A
C
D
H
H
N
LL
A
A
D
CJJ
F

9HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly - Hanging the Fan
Attaching the fan to the
electrical box Hanging the fan
□Pass the 120-Volt supply wires through the center hole in the
mounting bracket (A).
□Install the ceiling mounting bracket on the outlet box by sliding
the mounting bracket (A) over the two screws (II) provided with
the outlet box. If necessary, use leveling washers (not included)
between the mounting bracket (A) and the outlet box. Note that
the at side of the mounting bracket (A) is toward the outlet box.
When using close-to-ceiling mounting, it is important that the
mounting bracket be level.
□Securely tighten the two mounting screws (II).
1 2
WARNING: To reduce the risk of re, electric shock or personal
injury, mount to outlet box marked “Acceptable for fan support
of 35 lbs. (15.9 Kg) or less”, and use screws provided with the
outlet box.
□Carefully lift the fan-motor assembly (F) up to the slide-
on mounting bracket (A).
□Insert the ball portion of the ball/downrod assembly (B)
into the socket of the slide-on mounting bracket (A).
□Turn the ball/downrod assembly (B) clockwise until it is
seated with the tab of the slide-on mounting bracket (A)
and aligned with the slot in the ball.
□If using close-to-ceiling mounting, hang the fan on the
hook (OO) provided by utilizing one of the holes at the
outer rim of the ceiling canopy (C).
OO
F
D
C
A
Standard mount
Close to ceiling mount
A
II
II
A
B
C
D
E
F

10
Assembly - Hanging the Fan (continued)
Making the electrical connection
□The fan comes with 54 in. lead wires for use with an extended
ball/downrod assembly. If using the 6 in. ball/downrod
assembly (B) provided, you can cut the lead wires to your
desired length (no shorter than 12 in.) This will make extra
room in the canopy (C), if you do not wish to cut the wires,
you will need to neatly wrap them.
□Connect the fan motor green wire(s) to the household green
or bare wire using a wire connecting nut (EE).
□Connect the fan motor white wire to the household white wire
using a wire connecting nut (EE).
□Connect the fan motor black and blue wires to the household
black wire using a wire connecting nut (EE).
□Secure each wire connecting nut using electrical tape.
□Turn the wire connecting nut (EE) upward and push the wiring
into the outlet box (MM).
3
IMPORTANT: Use the wire connecting nuts (EE) supplied with
your fan. Secure the connectors with electrical tape and ensure
there are no loose strands or connections.
NOTE: The fan comes with 54 in. lead wires for use with
an extended ball/downrod assembly. If using the 6 in. ball/
downrod assembly (B) provided, you can cut the lead wires to
your desired length (no shorter than 12 in.).
WARNING: Remove the rubber motor stops on the bottom of
the fan before installing the blades or testing the motor.
Wrapping the extra wire
□Gently wrap the excess wire around the mounting bracket,
under the receiver.
□Secure with electrical tape.
4
NOTE: Follow this step ONLY if you did not cut the extra length off
from the wires coming from the ceiling fan.
White Green
Green or Bare
Black
Blue and Black
C
A
B
Outlet box
(MM)
EE

11 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Mounting the fan-motor assembly
(standard mount)
5
Assembly - Hanging the Fan (continued)
WARNING: When using the standard ball/downrod mounting, the
tab in the ring at the bottom of the mounting bracket must rest in
the groove of the hanger ball. Failure to properly seat the tab in
the groove could cause damage to the wiring.
□Align the locking slots of the ceiling canopy (C) with the two
screws (LL) in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock in place. Do not tighten screws
(LL).
□Install the two mounting screws (HH) (saved from Assembly Step
1 “preparing for mounting” into the holes in the canopy (C) and
tighten rmly.
□Firmly tighten the two mounting screws (LL).
□Install the decorative canopy ring (D) by aligning the ring’s slots
with the screws in the canopy (C). Rotate the ring clockwise to
lock in place.
HH
E
F
D
C
B
LL
A
F
C
D
H
H
Standard mount
WARNING: The locking slots of ceiling canopy are provided only
as an aid to mounting. Do not leave the fan assembly unattended
until all four canopy screws are engaged and rmly tightened.
Close to ceiling mount

12
Assembly - Attaching the Fan Blades
Attaching the blades
to blade brackets
1
□Remove and save the rubber plug (FF) from the switch cup to
allow screw driver access when attaching blade arms.
□Fasten the blade bracket (I) to the motor (F) by inserting
the alignment post into the slot on the bottom of the fan
motor assembly (F) and tightening the motor screws that are
preassembled to the blade bracket (I).
□Repeat for the remaining four blade brackets (I).
□Insert the rubber plug (FF) into the hole in the switch cup.
IMPORTANT: Insert the rubber plug (FF) to prevent
water from entering the switch housing and to reduce
the risk of re, electric shock, or other personal
injury.
I
FF
F
Attaching the fan blades
2
□Mount the fan blades (H) to the blade bracket (I) by aligning
the three key-slot holes in the blade (H) with the three posts
on the top of the blade brackets (I).
□Hold the blade (H) close to the blade bracket (I) and press
the blade (H) down rmly. Ensure the key-slot holes are
properly seated on the blade arm posts.
□While still holding the blade (H) down, rmly slide the blade
(H) away from the bracket(I) side until the blade (H) engages
in the locking mechanism .
□Make sure the locking mechanism at the rear of the blade
bracket (I) springs upward and butts against the edge of the
blade (H) indicating a secure connection.
□Visually inspect the top of the blade bracket (I) to ensure the
locking mechanism is securely in place.
□Repeat for the remaining blades (H).
H
I

13 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Assembly - Attaching the Light Kit
Attaching the light kit
1
□Remove the three screws (QQ) from the light kit tter
assembly (G).
□Remove the nial (GC) and glass bowl (GB) from the light
kit assembly (G).
□Connect the wires exiting the bottom of the motor
assembly (F) by connecting the molded adaptor plugs
together (blue to blue, white to white).
□Slide the light kit (G) into the switch housing and secure it
using the three screws (QQ) that were removed in the rst
step.
CAUTION: To reduce the risk of electric shock,
disconnect the electrical supply circuit to the fan
before installing the light kit.
Installing the bulbs and attaching the
glass bowl
2
□With power off, install the two bulbs (J) by twisting them
into the light bulb sockets.
□Position the glass bowl (GB) over the threaded nipple and
re-install the nial (GC).
□Attach the pull chain extensions (BB).
CAUTION: Make sure the power is off before attaching
or removing the glass bowl (GB).
CAUTION: Over lamping the fan will result in the fan
lights shutting down until the proper wattage bulbs
are installed. Reset the lights by turning off the power,
replacing the bulbs with the correct wattage bulbs, and
turn the power on.
GA
GB
GC
QQ
QQ
GA
GA
BB
GB
GC
J

14
Assembly - Assembling the Fan without the Light Kit
Attaching the switch cup cover
2
□Remove the three screws (QQ) from the switch cup cover (GE)
and save them.
□Align the three holes in the switch cup below the fan motor
assembly with the three holes in the switch cup cover (GE).
Make sure the notch the in switch cup cover (GE) clears the
reversing switch in the switch cup.
□Position the switch cup cover (GE) and re-install the three
screws that were removed in the rst step to secure the switch
cup cover (GE).
□Install plastic plug (GG) into hole of the switch cup cover (GE).
□Attach the pull chain extension (BB) to the fan pull chain.
NOTE: Notice the location of the fan’s reverse slide switch. This
is the switch used to change the fan’s directional rotation. For
more information on the operation of this switch, see Operating
Your Fan on page 12.
QQ
BB
GG
GE
Removing switch cup from glass bowl
1
□In order to use the fan without the light kit, remove the switch
cup cover (GE) from the top of the light kit tter assembly (G) by
removing the center hex nut (GD) inside the switch cup cover,
and then thread the switch cup cover off of the threaded nipple
on the top of the light kit tter assembly (G).
GD
GE

15 HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Operation
Turn on the power and check the operation of the fan. The pull
chain controls the fan speeds as follows:
1 pull - High, 2 pulls - Medium, 3 pulls - Low, 4 pulls - Off
The appropriate speed settings for warm or cool weather depends
on factors such as the room size, ceiling height, and number of
fans.
The fan is shipped from the factory with the reversing switch
positioned to circulate air downward. If airow is desired in the
opposite direction, turn your fan off and wait for the blades to stop
turning, then slide the reversing switch (XX) (located in switch cup)
to the opposite position, and turn the fan on again. The fan blades
will turn in the opposite direction and reverse airow.
Warm weather - (Forward) A downward airow creates a cooling
effect. This allows you to set your air conditioner on a warmer
setting without affecting your comfort.
Cool weather - (Reverse) An upward airow moves warm air off
of the ceiling. This allows you to set your heating unit on a cooler
setting without affecting your comfort.
NOTE: Wait for the fan to stop before reversing the direction of
blade rotation.
Warm weather
Cool weather
XX
XX

16
Troubleshooting
Problem Solution
The fan will not start. □Check the main and branch circuit fuses or breakers.
□Check the line wire connections to the fan and switch wire connections in the switch housing.
The fan is noisy. □Ensure all motor housing screws are snug.
□Ensure the screws that attach the fan blade bracket to the motor hub are tight.
□Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
□Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.
□If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light
bulbs are also secure.
□Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
□Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.
The fan wobbles. □Check that all blade and blade arm screws are secure.
□Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on
the ceiling above the tip of one of the blades. Measure from a point on the center of the blade to the point on the
ceiling. Rotate the fan until the next blade is positioned for measurement, and measure from the same point on
each blade to the ceiling. Repeat for each blade. Any measurement deviation should be within 1/8 in. Run the fan
for ten minutes. If the fan continues to wobble please contact Customer Service and a balancing kit will be sent
to you at no charge.
□Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade
attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
□Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage
the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the nish. The
plating is sealed with a lacquer to minimize discoloration or tarnishing.
□You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a
light application of shoe polish.
□You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.
WARNING: Make sure the power is off before cleaning
your fan.
Care and Cleaning

Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
Retain this manual for future use.

GUÍA DE USO Y MANTENIMIENTO
VENTILADOR DE TECHO PALMARIA DE 1,32 M
Artículo Núm. 1008 655 076
Modelo Núm. 92408
Modelo Núm. EF200S(X)-52
aprobado por UL
¿Preguntas, problemas, piezas faltantes? Antes de devolver a la tienda,
llama al servicio al cliente de Hampton Bay
entre 8 a.m. y 7 p.m. (Este), de lunes a viernes, o los sábados de 9 a.m. a 6 p.m. (Este).
1-855-HD-HAMPTON
HAMPTONBAY.COM
GRACIAS
Apreciamos la plena conanza que has depositado en Hampton Bay con la compra de este ventilador de techo. Nos esforzamos constantemente
por crear productos de calidad diseñados para tu hogar. Visítanos por Internet para ver nuestra línea completa de productos disponibles a n de
satisfacer tus necesidades de mejoras del hogar. ¡Gracias por elegir Hampton Bay!

2
Tabla de contenido ..............................................................2
Información de seguridad...................................................2
Garantía................................................................................ 3
Preinstalación ......................................................................3
Instalación............................................................................6
Ensamblaje........................................................................... 7
Operación........................................................................... 12
Mantenimiento y limpieza.................................................13
Solución de problemas .....................................................13
1. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/
NFPA 70 y con los códigos eléctricos locales. La instalación eléctrica debe
hacerse por un electricista calicado con licencia.
2. La caja eléctrica y estructura de soporte tienen que montarse de forma segura
para poder sostener con conanza 35 lb (15.9 kg). Usa solo cajas eléctricas
aprobadas por UL y marcadas como “Apropiada para sostener ventiladores de
35 lb (15.9 kg) o menos”.
3. El ventilador tiene que montarse con separación mínima de 2.1 m entre el
borde trasero de las aspas y el piso.
4. No usar el interruptor de reversa mientras las aspas del ventilador estén en
movimiento. Tienes que apagar el ventilador y detener las aspas antes de
invertir su dirección de giro.
5. No coloques objetos en la trayectoria de las aspas.
6. Los diagramas eléctricos son solo para referencia. Los kits de luces no
empaquetados con el ventilador tienen que estar aprobados por UL y marcados
como apropiados para usar con el modelo de ventilador que estás instalando.
Los interruptores tienen que estar clasicados de uso general por UL. Para
ensamblar bien, consulta las instrucciones adjuntas a los kits de luces e
interruptores.
7. Después de concluir las conexiones eléctricas, debes voltear los conductores
empalmados hacia arriba y meterlos con cuidado en la caja eléctrica. Los
cables deben estar separados, con el cable a tierra y el conductor a tierra del
equipo hacia uno de los lados de la caja eléctrica y el conductor sin conexión a
tierra hacia el lado opuesto.
8. Antes de la instalación, todos los tornillos de jación tienen que comprobarse y
reajustarse donde sea necesario.
9. Adecuado para usar en lugares húmedos al instalarse en un circuito derivado
protegido por un interruptor diferencia (GFCI, por sus siglas en inglés). Usar solo
con kits de luces marcados como “Adecuados para uso en lugares húmedos".
ADVERTENCIA: Para reducir el riesgo de lesiones
personales, no dobles los soportes de las aspas
(también llamados “bridas”) durante ni después de
la instalación. No coloques objetos en la trayectoria
de las aspas.
ADVERTENCIA: Para reducir el riesgo de incendio o
descarga eléctrica, no utilices este ventilador con ningún
dispositivo de estado sólido para control de velocidad.
ADVERTENCIA: Quita los tapones de goma del motor
en la parte inferior del ventilador antes de instalar
las aspas o de vericar el motor.
ADVERTENCIA: Para evitar posible descarga eléctrica,
desconecta la electricidad en la caja principal de
fusibles antes de cablear. En caso de no tener suciente
conocimiento o experiencia sobre cableado eléctrico,
contactar a un electricista certicado.
Información de seguridad
Tabla de contenido
PRECAUCIÓN: Para reducir el riesgo de lesiones
personales hay que usar sólo los tornillos incluidos
con la caja eléctrica.
PRECAUCIÓN: Para evitar lesiones físicas o daños al
ventilador y otros artículos, ten cuidado al limpiarlo o
al trabajar cerca de él.
ADVERTENCIA: Para reducir el riesgo de incendio,
descarga eléctrica o lesiones, instala sólo en una
caja eléctrica clasicada como “apropiada para
sostener ventiladores de 35 lb (15.9 kg) o menos” y
usa sólo los tornillos incluidos con la caja eléctrica.
LEE Y GUARDA ESTAS INSTRUCCIONES.
ADVERTENCIA: Para disminuir los riesgos de
incendio, descarga eléctrica o lesiones personales,
no uses repuestos que no sean recomendados por
el fabricante (p. ej., piezas hechas en casa con una
impresora 3D).
Este equipo fue sometido a prueba y se determinó que cumple con los límites establecidos para un dispositivo digital Clase B según la Parte 15 de las Normas FCC. Estos límites fueron
establecidos para dar protección razonable contra la interferencia dañina en uso residencial. Este equipo genera, consume y puede irradiar energía de radiofrecuencia; si no se instala y
usa de acuerdo con las instrucciones, puede causar interferencia nociva a comunicaciones radiales. Sin embargo, no hay garantía de que no ocurrirá interferencia en cierta instalación
particular. Si este equipo causa interferencia perjudicial a la recepción de radio o televisión, que puede determinarse encendiendo y apagando el equipo, se recomienda al usuario tratar
de corregir la interferencia con una o más de las siguientes medidas:
– Reorientar o reubicar la antena receptora.
– Incrementar la distancia entre los equipos y el receptor.
– Conectar el equipo a un tomacorriente en circuito distinto del receptor.
– Pedir asistencia al concesionario o a un técnico de radio/TV con experiencia.
PRECAUCIÓN:
Los cambios o modicaciones sin aprobación expresa del responsable de este dispositivo podrían anular el derecho del usuario a operar el equipo.
Este dispositivo cumple con la Parte 15 de las Normas FCC. Su operación está sujeta a las dos condiciones siguientes: (1) Este dispositivo no debe causar interferencia dañina y (2) tiene
que aceptar cualquier interferencia recibida, incluyendo aquella que pudiera afectar su funcionamiento.
Parte responsable - Información de contacto en EE. UU.: King of Fans, Inc 1951 NW 22nd Street, Fort Lauderdale, FL 33311, [phone]

3HAMPTONBAY.COM
Llame al 1-855-HD-HAMPTON para mayor asistencia.
Preinstalación
Garantía
ESPECIFICACIONES
HERRAMIENTAS NECESARIAS
NOTA: Estas medidas son aproximadas. No incluyen el
amperaje ni el vataje consumido por el kit de luces.
Destornillador
Phillips
Destornillador
plano
Llave ajus-
table
Cinta de
electricista Cortacables
Escalera de tijera
Tamaño Velocidad Voltios Amperios Vatios RPM CFM Peso
neto
Peso
bruto
Pies
cúbicos
1.32 m
Baja
Media
Alta
120
0.23
0.33
0.51
11.86
24.42
61.48
68
98
156
2098
3071
4962
18.97 lbs
(8.6 kg)
25.13 lb
(11.40 kg)
1,996 pies
cúbicos
El proveedor garantiza de por vida, a partir de la fecha de adquisición por el comprador original, que el motor del ventilador no presenta defectos de
fabricación ni de materiales al momento del envío desde la fábrica. El proveedor garantiza que el kit de luces, excluyendo cualquier vidrio, no tendrá
defectos de fabricación ni de material en el momento del envío desde la fábrica por un período de tres años después de la fecha de compra por
parte del comprador original. El proveedor también garantiza, por un año a partir de la fecha de adquisición por el comprador original, que ninguna
de las demás piezas del ventilador, excluyendo las aspas de vidrio o acrílico, presenta defectos de fabricación ni de materiales al momento del envío
desde la fábrica. Si el producto es devuelto, aceptamos reparar sus defectos sin cargo alguno o, a nuestra discreción, reemplazarlo por modelo
similar o superior. Para obtener servicio de garantía tiene que presentar una copia del recibo como comprobante de compra. Todos los costos de
retiro y reinstalación del producto correrán por cuenta del cliente. Los daños a cualquier pieza por accidente, instalación o uso inadecuado, o por
montar cualquier accesorio, no están cubiertos por esta garantía. Puesto que las condiciones climáticas pueden variar, esta garantía no cubre
ningún cambio del acabado en latón, como óxido, perforación, corrosión, manchas o descascaramiento. Este tipo de acabados en latón tiene una la
vida útil prolongada si se lo protege contra las condiciones climáticas cambiantes. Cierta “oscilación” es normal y no debe considerase un defecto.
Cualquier servicio prestado por personal no autorizado invalidará la garantía. No hay ninguna otra garantía expresa. Por este medio y en el alcance
permitido por la ley, Hampton Bay queda exonerado de toda garantía, incluso, pero sin limitarse a ellas, aquellas de comercialización e idoneidad
para un n determinado. La duración de cualquier garantía implícita que no pueda exonerarse se limita al plazo especicado en la garantía explícita.
Algunos estados no permiten limitaciones sobre la duración de las garantías implícitas, así que es posible que la limitación anterior no se aplique
en su caso. El minorista no será responsable por daños incidentales, emergentes ni especiales derivados del uso o funcionamiento del producto,
excepto en los casos en los que la ley así lo disponga. Algunos estados no permiten excluir ni limitar daños directos o indirectos, así que es posible
que la limitación o exclusión anterior no se aplique en este caso. Esta garantía le otorga derechos legales especícos y es posible que también
goce de otros derechos que varían de un estado a otro. Esta garantía sustituye a todas las garantías anteriores. Los costos de envío en cualquier
devolución de productos como parte de un reclamo de garantía corren por cuenta del cliente.
Comuníquese con el equipo de servicio al cliente al teléfono 1-855-HD-HAMPTON o visite www.HamptonBay.com.