HAMPTON BAY SW19129-A ORB User manual

SKU/Model : #XXXX/#SW19129-A ORB
#XXXX/#SW19129-A BN
EMBRY HILLS LED 42 INCH CEILING FAN

READ AND SAVE THESE INSTRUCTIONS.

42 in. xxxx’
Ladder
xxxx xxx xxx xxxx
xxxx xxx xxx xxxx
xxxx xxx xxx xxxx
xxxx xxx
xxx xxx
We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period
of lifetime after the date of purchase by the original purchaser. And we warrant the LED light kit to be free from defects in workmanship
and material present at time of shipment from the factory for a period of 3 years after the date of purchase by the original purchaser.
We also warrant that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the
time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. We agree to correct such
defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service,
you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility.
Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty.
Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding,
tarnishing or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain
amount of "wobble" is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the
warranty invalid. There is no other express warranty. We hereby disclaim any and all warranties, including but not limited to those of
merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be
disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special
damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do
not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
givesd specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior
warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

Fiber washer
15+1 spare
15+1 spare
MM
NN
Blade arm screw
Mounting plate screw (preassembled)
Light kit plate screw (preassembled)
MM
NN
10+1 spare

9W LED bulbs
M
L
Blade arm
Glass shade
Switch box
1
5
5
M
Light kit plate

MM
OO
FF
II
FF
GG
EE
GG
HH
Loosen the two set screws (II) from the coupling of the
fan motor assembly (H)
B
B
B
OO
OO
GG
II

PP
Hanging the fan motor assembly
to the mounting bracket
PP
F

the the
the
EB

in
Installing the canopy and canopy cover
JJ
JJ

AA
BB
Fastening the blades to the blade arms
Attach the fan blade (A) to the blade arm (I) by using the three blade screws (AA) and the three fiber washer (BB).
Tighten all blade screws (AA) and fiber washers (BB) securely.
Repeat same process for the other four blades (A).

Loose the five screws (QQ) and remove the five plastic blocks (RR) from the fan motor assembly (H) before attaching the blade
arm (I) to the fan motor assembly (H). Discard the five screws (QQ) and the five plastic blocks (RR).
Tighten the blade arm (I) onto the bottom of fan motor assembly (H) by using the two blade arm screws (CC). Repeat same
process for the other four blade arms (I).
QQ
RR
CC
I

Installing the switch box to the fan motor assembly
Remove one of the screws (KK) from the mounting plate of the fan motor assembly (H) and loosen the other two
screws (KK), but do not remove.
While holding the switch box (J) under your fan, firmly snap the wire connector plugs (SS) together.
Place the key holes
from the switch box (J) over the two screws (KK) previously loosened from the fan motor
assembly (H)
. Turn the switch box (J) until it locks at the narrow section of the key holes. Secure by tightening
the two screws (KK) previously loosened and the one screw (KK) previously removed.
KK
J
SS

Attaching the light kit plate to the the switch box
Remove one of the screws (LL) from the switch box (J) and loosen the other two screws (LL), but do not remove.
While holding the light kit plate (K) under your fan, snap the white connection plug from the switch box (J) to the
white connection plug from the light kit plate (K). Snap the black connection plug from the switch box (J) to the
black connection plug from the light kit plate (K).
Place the key holes
from the light kit plate (K) over the two screws (LL) previously loosened from tthe switch box (J).
Turn the light kit plate (K) until it locks at the narrow section of the key holes. Secure by tightening the two screws (LL)
previously loosened and the one screw (LL) previously removed.
CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan
Before Installing The Light Kit.
10
J
BLACK WHITE
K
LL

M
L
K
K
12
11
Install the 9W LED bulb (L) into the socket of
the light kit plate (K).
Installing the LED bulbs
16
Install the glass shade
Attach the glass shade (M) to the light kit plate (K) by
twisting tightly. (DO NOT OVERTIGHTEN)

UU VV
MM
WW
Reverse Function
The reverse switch (WW) is located on the surface of the switch box (J).
left
right
The 3-speed pull chain (UU)
The light kit pull chain (VV)
17
Attach the pull chain fobs (MM) to the chain on the light kit plate (K).

Balancing kit includes an
additional instruction manual within the packet.
10
18

Fiber washer
Flywheel screw
M
9W LED bulbs
M
L
Glass shade
19
Blade arm
Switch box
Light kit plate
MM
NN
MM
NN
Mounting plate screw (preassembled)
Light kit plate screw (preassembled)

CF542KP-01
HAMPTON BAY