HAMPTON BAY Greenfire GCi60-2 User manual

FPI FIREPLACE PRODUCTS INTERNATIONAL, LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
920-619 10.03.22
Greenre® GCi60-2
TECHNICAL MANUAL
Cast Iron
Pellet Insert
WARNING:
Improper installation, adjustment,
alteration, service or maintenance can
cause injury, property damage, or loss of
life. Refer to this manual. For assistance or
additional information consult an authorized
installer or service agency.
FOR YOUR SAFETY:
Do not store or use gasoline or other ammable
vapours and liquids in the vicinity of this or
any other appliance.
Installation and service must be performed
by an authorized installer or service agency.
Tested by:
Contact your building or fire officials about restrictions and installation
inspection requirements in your area.
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS
PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
IMPORTANT: SAVE THESE INSTRUCTIONS
French Manual: https://bit.ly/3eGZjtF
Manuel en Français : https://bit.ly/3eGZjtF

Hampton GCi60-2 Cast Pellet Insert Technical Manual
2
Safety Note: If this stove is not properly installed, a house re may result. For your safety,
follow the installation instructions, contact local building, re ocials, or authority having jurisdiction about
restrictions and installation inspection requirements in your area.
The authority having jurisdiction should be consulted before installation to determine the need to obtain a
permit.
Emissions and Efficiency: This manual describes the installation and operation of the Regency GCi60-2 pellet
heater. This heater is U.S. ENVIRONMENTAL PROTECTION AGENCY certified to comply with 2020 particulate
emission standards. Under specific test condition this heater has been shown to deliver heat at rates raging from:
7,817 - 38,437 Btu/hr
Efficiency: 78% (HHV)* (PFS TECO 21-703)
*When using 4’’ (102 mm) to 6’’ (152 mm) flue increaser. See technical manual for further information.
Note: The 78% (HHV) when tested was achieved burning wood pellets only.
FIRE EXTINGUISHER AND SMOKE DETECTION: All home with a pellet burning stove should have at
least one fire extinguisher in a central location known to all the household. Smoke detectors and carbon
monoxide detectors should be installed maintained in the room containing the stove. If it sounds the alarm,
correct the cause but do not deactivate. You may choose to relocate the smoke the smoke detection device
within the room; DO NOT REMOVE THE SMOKE OR CARBON MONOXIDE DETECTORS FROM THE
ROOM.
WARNING: This wood heater needs periodic inspection and repair for proper operation. It is against federal
regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual.
WARNING: This wood heater has a manufacturer set minimum low burn rate that must not be altered.
It is against federal regulations to alter this setting or other wise operate this wood heater in a manner
inconsistent with operating instructions in this manual.

Safety Warnings & Recommendations...................................................................4
Specifications......................................................................................................6
Rating Label & Location.................................................................................6
Specifications......................................................................................................7
Dimensions.................................................................................................. 7
Specifications................................................................................................7
Installation.........................................................................................................8
Deciding Where to Locate your Pellet Appliance .............................................8
Removing Pellet Stove From Pallet ................................................................8
Installing the Insert Frame & Levelling...........................................................9
Oversize Filler Panel (Part # GCI60-918).......................................................10
Thermostat Installation................................................................................10
Minimum Fireplace opening:.........................................................................11
Clearances to Combustibles..........................................................................11
Minimum Fireplace Opening .........................................................................11
Vent Termination Requirements.....................................................................12
Outside Fresh Air Connection........................................................................13
Exhaust And Fresh Air Intake Locations.........................................................13
Masonry Fireplace Installation ......................................................................14
Positive Flue Connection without a Full Reline (USA Only) ..............................15
Built-In Installation .....................................................................................16
Horizontal Exhaust Through Wall Installation ................................................17
Outside Vertical Installations .......................................................................19
Inside Vertical Installations .........................................................................20
Slider/Damper Set-Up .................................................................................21
Troubleshooting................................................................................................22
Wiring Diagram.................................................................................................26
Parts List..........................................................................................................27
Parts Diagram - Components.............................................................................30
Parts Diagram - Steel........................................................................................31
Warranty..........................................................................................................32
Table of Contents
Hampton GCi60-2 Cast Pellet Insert Technical Manual 3

Safety Warnings & Recommendations
*This manual is designed for the technician in conjunction with the owner’s manual.*
Please read this entire Technical Manual before installing or operating your Hampton Pellet Stove.
Failure to follow these instructions may result in property damage, bodily injury or even death.
Any unauthorized modification of the appliance or use of replacement parts not recommended
by the manufacturer is prohibited. All national and local regulations shall be complied with when
operating this appliance.
Caution: Do not connect to any air distribution duct or system.
Warning: Never place wood, paper, furniture, drapes or other combustible materials within 48” (122cm) of the
front of the unit, 12” (30.5cm) from each side, and 3” (7.6cm) from the back of the unit. Do not let children or
pets touch it when it is hot.
To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation
instructions. A Hampton dealer will be happy to assist you in obtaining information with regards to your local
building codes and installation restrictions.
FIRE EXTINGUISHER AND SMOKE DETECTION: All homes with a pellet burning stove should have at
least one fire extinguisher in a central location known to all in the household. Smoke detectors should be
installed and maintained in the room containing the stove. If it sounds the alarm, correct the cause but do not
deactivate. You may choose to relocate the smoke detection devise within the room; DO NOT REMOVE THE
SMOKE DETECTOR FROM THE ROOM.
CHIMNEY OR RUN AWAY FIRE: Call local fire department (or dial 911). Close the draft fully. Extinguish the
fire in the burn pot liner with a cup of water and close the door. Examine the flue pipes, chimney, attic, and roof
of the house, to see if any part has become hot enough to catch fire. If necessary, spray with fire extinguisher
or water from the garden hose. IMPORTANT: Do not operate the stove again until you are certain the chimney
and its lining have not been damaged.
OPERATION: The door and ash drawer must be kept closed when the unit is in operation to prevent fume
spillage and for proper and safe operation of the pellet stove. Also ensure all gaskets on the door are checked
and replaced when necessary. Unit hot while in operation. Keep children, clothing and furniture away.
Contact may cause skin burns.
CAUTION: When operating during adverse weather, if the unit exhibits dramatic changes in combustion stop
using the unit immediately.
FUEL: This stove is designed and approved to only burn wood pellets of any quality, corn, wheat, and barley.
Dirty fuel will adversely affect the operation and performance of the unit and may void the warranty. Check with
your dealer for fuel recommendations. THE USE OF CORD WOOD IS PROHIBITED BY LAW. Do not burn
garbage or flammable fluids such as gasoline, naphtha or engine oil.
SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which will
collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house.
Frequently check your stove and adjust the slider/damper as needed to ensure proper combustion. See:
“Slider/damper Setting”.
CLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This will vary
due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect and clean the
exhaust vent semi-annually or every two tons of pellets.
The appliance, flue gas connector and the chimney flue require regular cleaning. Check them for blockage prior
to re-lighting after a prolonged shut down period.
ASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container of
ashes should be on a non-combustible surface, well away from all combustible materials pending final disposal.
If the ashes are disposed of by burial in soil or otherwise locally dispensed, they should be retained in the closed
container until all cinders have thoroughly cooled.
Hampton GCi60-2 Cast Pellet Insert Technical Manual
4

Safety Warnings & Recommendations
ELECTRICAL: The use of a surge protected power bar is highly recommended. The unit must be
grounded. The grounded electrical cord should be connected to a standard 110-120 volts (4.2 Amps), 60 hertz
electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power
cord must be purchased from the manufacturer or a qualified Hampton dealer. Be careful that the electrical cord
is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s maximum
power requirement is 504 watts.
GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with
broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an Hampton dealer.
Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot. To clean the
glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner, or take a damp paper
towel and dip into the fly ash. This is a very mild abrasive and will not damage the glass.
KEEP ASH PAN FREE OF RAW FUEL. DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A fire
in the ash pan may occur.
INSTALLATION: Contact your local building or fire official to obtain a permit and any information on installation
restrictions and inspection requirements for your area.
Be sure to maintain the structural integrity of your home when passing a vent through walls, ceilings, or roofs,
and all construction meets local building codes. It is recommended that the unit be secured into its position
in order to avoid any displacement. This appliance must be installed on a floor with an adequate load bearing
capacity, if existing construction doesn’t meet load capacity, suitable measures (e.g. load distributing plate)
must be taken to achieve it.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
FRESH AIR: This unit uses large quantities of air for combustion; outside Fresh Air connection is strongly
recommended. Fresh Air must be connected to all units installed in Mobile and “Air Tight Homes” (R2000) or
where required by local codes.
Consider all large air moving devices when installing your unit and provide room air accordingly. NOTE:
Extractor fans when operating in the same room or space as the appliance may cause problems. Limited air for
combustion may result in poor performance, smoking and other side effects of poor combustion.
The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive chimney
pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash pan and
viewing door must be locked securely for proper and safe operation of the pellet stove.
Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper combustion air
is admitted to the combustion chamber. Setting the proper combustion air is achieved by adjusting the slider
damper located on the left side of the stove.
Soot or creosote may accumulate when the stove is operated under incorrect conditions such as an rich burn
(black tipped, lazy orange flames).
If you have any questions with regards to your stove or the above-mentioned information, please feel free to
contact your local dealer for further clarification and comments.
SINCE REGENCY FIREPLACE PRODUCTS LTD. HAS NO CONTROL OVER THE INSTALLATION OF
YOUR STOVE,REGENCY FIREPLACE PRODUCTS LTD. GRANTS NO WARRANTY IMPLIED OR STATED
FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE,REGENCY FIREPLACE
PRODUCTS LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
Hampton GCi60-2 Cast Pellet Insert Technical Manual 5

Specifications
rating label & location:
The rating label is located on the top of the hopper.
Figure 1: GCi60-2 Rating Label
Model / Modèle:
GCI60-2
Listed Room Heater, Pelletized Fuel Type (Appareil de chauffage à granules certifié) Input rating when using (Le chauffage d'énergie avec): Wood Pellets/Corn (Boulettes de bois/lMaïs) - 55,000BTU (16.1KW*hr) Wheat/Barley (Blé/l'Orge) - 53,000BTU (15.5KW*hr) Install and use only in accordance with the manufacturer's installation and operating instructions. Contact local building or fire officials about restrictions and installation inspection in your area. Do not connect this unit to a chimney flue serving another appliance. Inspect and clean exhaust venting system frequently. See local building code and manufacturer's instructions for precautions required for passing a chimney through a combustible wall or ceiling. ELECTRICAL RATING: 120 Volts, 60Hz, 4.2 Amps. Route Cord Away From Heater. For use with pelletized solid fuels - wood, corn, wheat, & barley only. Operate only with viewing door and ash removal door closed. Only replace glass with ceramic glass. Components required for installation: listed 4inch (100 mm) stainless steel chimney liner.
Installez et utilisez cet appareil seulement selon les instructions d'installation et d'opération du fabricant. Contactez les autorités locales de votre quartier concernant les restrictions et les inspections d'installation. Inspectez et nettoyez le système d'échappement fréquemment. Consultez les codes de bâtiment locaux et les instructions du fabricant pour les précautions à prendre lorsque une cheminée doit être installée au travers un mur ou un plafond combustible. CLASSEMENT ÉLECTRIQUE : 120 Volts, 60 Hz, 4.2 Amps. Placez le câble électrique loin de la chaleur. Utilisation avec granules - le bois, le maïs, le blé, & l'orge seulement. Utiliser seulement lorsque les portes avants et la porte du réceptacle de cendre sont fermées. Si une ou des vitres devaient être remplacées, utilisez seulement du verre céramique. Les composantes requises pour l'installation: une rêvetement de cheminée reprisé en acier inoxydable 4”.
DATE OF MANUFACTURE /
DATE DE FABRICATION:
J F M A M J J A S O N D 2022 2023 2024
CAUTION:
HOT WHILE IN OPERATION. DO
NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE
AWAY. CONTACT MAY CAUSE
BURNS. SEE NAMEPLATE AND
INSTRUCTIONS.
ATTENTION: L'APPAREIL EST CHAUD LORSQU'IL FONCTIONNE. NE PAS TOUCHER. GARDER LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES ÉLOIGNÉS DE L'APPAREIL EN MARCHE. UN CONTACT AVEC CELUI-CI POURRAIT RÉSULTER EN DES BRÛLURES. VEUILLEZ VOIR LA PLAQUE DU FABRICANT ET LES INSTRUCTIONS.
DO NOT REMOVE THIS LABEL /
NE RETIREZ PAS CETTE ÉTIQUETTE
Serial No. / No. De Serié:
To Start Stove: Select fuel type mode; PREMIUM PELLETS for superior quality pellet fuel, REGULAR PELLETS for all grades of wood pellets & MULTIFUEL for all other fuels. Press the ON / OFF button. For first time use, a small handful of pellets in the burn pot liner will speed up ignition.
A Sidewall to center of unit (
De la paroi au centre de l'unité)
24” (610 mm)
B Sidewall to surround panel (De la paroi à l'entoure le panneau) 2” (51 mm) C Bottom of unit to an unshielded 12” (305 mm) mantle (Le fond de l'unité à un manteau de cheminée non blindé) 33“ (838 mm) D Unit to top facing (protruding ¾” [19 mm]) (
De l'unité au sommet du parement)
0” (0 mm)
E Unit to side facing (protruding ¾” [19 mm]) (
De l'unité au côté du parement)
0” (0 mm)
F From door opening of unit to edge of floor protection (De la porte ouvrant au devant de protection de plancher) 6” (152 mm) G From side of unit to edge of floor protection (De l'ouverture de porte pour prendre parti de protection de plancher) 6” (152 mm)
C
A
E
B
D
Adjacent wall
GF
Combustible floors must be protected by a non-combustible material. - See Owners Manual. Le plancher combustible doit être protégé par un matériel incombustible. - Consultez le manual.
INSTALLED AS A FIREPLACE INSERT STOVE MODEL (FPI) / A INSTALLE COMME UN MODELE SUR PIED DE POELE. Minimum clearances to combustible materials./ Les dégagements minimums aux matériels combustibles:
This pellet heater needs periodic inspection and repair for proper operation. Consult the owner`s manual for further information. It is against federal regulations to operate this heater in a manner inconsistent with the operating instructions in the owner`s manual. U.S. ENVIRONMENTAL PROTECTION AGENCY Certied to comply with 2020 particulate emission standards. Under specic test conditions this heater has been shown to have a particulate emission level of 1.9 g/hr. Ce poêle à granulés besoins inspection périodique et la réparation pour un fonctionnement correct. Consultez le manuel d'owner`s pour plus d'informations. Il est contre les règlements fédéraux pour exploiter cette pastille chaue d'une manière incompatible avec les instructions de fonctionnement dans le manuel d'owner`s. Ce poêle répond aux normes limites d'émission de l'Environmental Protection Agency des États-Unis 2020. Dans des conditions de test spéciques, ce poêle a été montré pour avoir un niveau d'émission de particules de 1.9 g / h.
To Operate Stove: MANUAL MODE: When a fire has been established the stove settings are adjustable. / HIGH/LOW MODE: (Requires a thermostat) When the thermostat calls for heat the stove settings are adjustable. When the thermostat contacts open, the HEAT LEVEL and Fans will drop down to the LOW setting until the thermostat contacts close again. / AUTO/OFF MODE: (Requires a thermostat) When the thermostat contacts close, the unit will light automatically. Once up to temperature the stove settings are adjustable. When the thermostat contacts open, the stove will drop down to the LOW settings for 30 minutes. If within the 30 min the thermostat contacts close, the HEAT LEVEL will return to previous MANUAL setting or if the thermostat contacts remain open the stove begin its shutdown routine and it will restart when the thermostat closes. To Turn Off Stove: MANUAL and HI / LOW mode: Press the ON / OFF button AUTO / OFF mode: Turn the thermostat down or off. Pour démarrer le poêle: Choisir le mode pour le carburant ; PREMIUM PELLETS pour le carburant de boulette de qualité de superior, REGULAR PELLET pour tous degrés de boulettes de bois & MULTIFUEL pour tous autres carburants. Appuyer sur le bouton "ON/OFF". Pour l’usage de première fois, une petite poignée de boulettes dans le pot de brûlure hâtera l'allumage. Pour faire fonctionner le poêle : MODE MANUEL : Lorsque le feu est bien établi, les réglages peuvent être ajustés. / MODE "HIGH/LOW" : (Nécessite un thermostat) Lorsque le thermostat requière de la chaleur, les réglages peuvent être ajustés. Lorsque les contacts du thermostat ouvrent, le réglage du niveau de chaleur et les ventilateurs s'ajusteront au réglage " bas " jusqu'à ce que les contacts du thermostat se referment. / MODE "AUTO/OFF" : (Nécessite un thermostat) Lorsque les contacts du thermostat ferment, le poêle s'allumera automatiquement. Lorsque la température adéquate est atteinte, les réglages peuvent être ajustés. Lorsque les contacts du thermostat ouvrent, le poêle s'ajustera aux réglages "LOW" pendant 30 minutes. Si les contacts du thermostat sont fermés pendant ces 30 minutes, le réglage de niveau de chaleur retournera en réglages "MANUEL" ou si les contacts du thermostat restent ouverts, le poêle entamera le processus d'arrêt et il vouloir redémarrer lorsque les contacts du thermostat refermer. Pour éteindre le poêle : MODE MANUEL ET " HIGH/LOW " : Appuyer sur le bouton "ON/OFF". MODE "AUTO / OFF" : Régler le thermostat à la baisse ou éteignez le.
920-571
Certified for use in Canda & USA. Refer to
Intertek’s Directory of Building Products for
detailed information / Certifié pour installation au
Canada et aux Etats-Unis.Reportez-vous au
répertoire des produits de construction d'Intertek
pour des informations détaillées.
C#4001609
MANUFACTURED FOR /
FABRIQUE POUR:
PFS TECO REPORT #21-703
FPI Fireplace Products International Ltd.
Delta, BC, Canada
584
GCI60-00
GCI60 DECAL LOCATION
The GCi60-2 rating plate will be located on the underside of the
hopper lid. (See picture)
DO NOT REMOVE DECAL FROM UNIT.
Hampton GCi60-2 Cast Pellet Insert Technical Manual
6

Specifications
dimenSionS:
Input rating when using: Wood Pellets/Corn - 55,000BTU (16.1KW•hr) & Wheat/Barley - 53,000BTU (15.5KW•hr).
Table 1: GCi60-2 Specifications.
Description Fuel type
Residential Pellet Heater 6mm (¼”) dia. Pellets - wood, corn, wheat, & barley*
Voltage Current Max Power
110 - 120 V 4.2 Amps 504 Watts
Frequency Hopper Capacity Consumption on Low
60 Hz up to 60 lb (36.3 Kg) 1.5 lb/hr (0.68 Kg/hr)*
Testing Standard Weight (with full hopper) Consumption on High
ASTM 1509-04 500 lb (227 Kg) 6.5 lb/hr (2.95 Kg/hr)*
*Note: Consumption will vary with the type and quality of pellets / fuel used.
SpecificationS:
Regular Cast Faceplate Dimensions
33 ⁄
43 ⁄
40 ⁄
16 ⁄
24 ¾
26 ⁄
22 ⁄
11 ¾
12 ¾
33 ⁄
43 ⁄
40 ⁄
16 ⁄
24 ¾
26 ⁄
22 ⁄
11 ¾
12 ¾
50.000
38.000
Oversize Filler Panel Dimensions
Hampton GCi60-2 Cast Pellet Insert Technical Manual 7

Installation
deciding Where to locate your pellet appliance:
1. Unit must be installed in a masonry fireplace or as a built-in installation if there is no masonary fireplace
present.
2. Do not install the stove in a bedroom or room where people sleep in.
3. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat
circulation.
4. Check clearances to combustibles and for the least amount of interference to house framing, plumbing,
wiring, etc.
5. You can vent the stove with approved flex pipe.
6. This unit uses large quantities of air for combustion; outside Fresh Air connection is strongly
recommended. Fresh Air must be connected to all units installed in Mobile and “Air Tight Homes”
(R2000) or where required by local codes.
7. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be
obtained from a ventilated crawlspace.
8. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest
electrical outlet.
removing pellet Stove from pallet:
1. Remove the wooden crating surrounding the unit.
2. Remove the cast top, cast sides, cast front, and the cast ash shelf.
3. Unclip the unit from the
lower frame.
4. Slide the unit forward and
then out.
5. Remove the two top bolts
on the pallet mounting
plates as shown in Fig. 3.
6. Remove entire frame as
one piece.
Figure 3: Mounting Plates securing stove to pallet
Hampton GCi60-2 Cast Pellet Insert Technical Manual
8

Installation
Figure 4: GCI60 Frame.
inStalling the inSert frame & levelling:
Warning: Careless installation is the major cause of safety hazards. Check all local building and safety
codes before installation of unit.
1. Mount Surround Panel to Insert Frame.
2. Place the Insert Frame into the fireplace cavity.
3. Adjust the four levelling bolts until the frame is level. If the fireplace has an un-level surface which
exceeds the length of the bolts, masonry bricks may be placed under the frame.
4. Once level, position the Insert Frame in the fireplace cavity so that the Surround Panel is flush with
the front of the fireplace.
5. Adjust the top anchor bolts to secure it to the lintel. Ready-rod may be substituted if the bolts are not
long enough.
E
DETAIL E
SCALE 1 : 8
Levelling Bolts
Anchor Bolts
NOTE: Surround Panel
removed for clarity
NOTE: Installer must attach the metal “replace altered” tag using screws or nails to the replace, in
a location readily visible should the replace insert be removed, if the replace has been modied to
accomodate the GCI60.
Hampton GCi60-2 Cast Pellet Insert Technical Manual 9

Installation
overSize filler panel (part # gci60-918):
1. If installing the Oversize Filler Panel (50”W x 38”H), do so before sliding unit into place.
2. Secure the filler panel to the backside of the cast faceplate using the 10 x #8 - 32 x 3/8” Thread Rolling
Screws.
[
7KUHDG5ROOLQJ6FUHZV
;
*&,)LOOHU3DQHO[
)LOOHU3DQHOLVVHFXUHGWR
WKHFDVWVXUURXQGXVLQJ
WHQ[77RU[
WKUHDGUROOLQJVFUHZV
5(9
*&,)LOOHU3DQHO,QVWDOODWLRQ
7+,6'5$:,1*,67+(3523(57<2)6+(5:22',1'8675,(6/7'$1'0$<127%(&23,('5(352'8&('2527+(5:,6(',6&/26(':,7+2877+(35,25$33529$/2)6+(5:22',1'8675,(6/7'
6KHUZRRG,QGXVWULHV/WG
+($775($70(17
6&$/(127726&$/(
),1,6+
3DUW'HVFULSWLRQ
6+((7 2)
thermoStat inStallation:
1. Install the wall thermostat (millivolt rated thermostat
recommended, or a 12/24 Volt rated thermostat set to
millivolts) in a location that is not too close to the unit
but will effectively heat the desired area.
2. Connect the Thermostat or Timer to the thermostat
wires on the unit. (Fig. 4)
If the heat in the room becomes too great, the high limit
switch may turn the stove off and the switch will have to
be manually reset. To reset the high limit switch:
-open the hopper lid
-remove plug under control panel
-use screwdriver to press down on the button on top of
the snap disk switch
Figure 4: Thermostat connection wires.
Hampton GCi60-2 Cast Pellet Insert Technical Manual
10